Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Design and performance of a velocity-matched broadband optical modulator with superconducting electrodes

Keiji Yoshida, T. Uchida, S. Nishioka, Y. Kanda, Satoshi Kohjiro

Published Jun 1, 1999• 2 citations
Publisher

Abstract

The performance of a LiNbO/sub 3/ optical modulator employing superconducting electrodes as a transmission line for a traveling-wave signal has been studied theoretically as well as experimentally. In the case of velocity matching between signal and optical waves using a shielding plane on top of a coplanar waveguide, numerical calculations of the attenuation constants of both superconducting and normal-conducting transmission lines indicate that the performance of the optical modulator can be far superior to that using normal-metals with respect to the figure of merit of bandwidth/driving-voltage. Microwave operation of a velocity-matched traveling-wave-type optical modulator with superconductor electrodes (NbN) has been successfully demonstrated. In the frequency range between dc and 26.5 [GHz] it is shown that the obtained modulation depth is in good agreement with the theoretically expected one.

DOI
10.1109/77.783764

Related papers

Design and performance of superconducting circuits for LiNbO/sub 3/ optical modulator and switch

Keiji Yoshida, Y. Kanda, H. Yoshihara +3 more

The design and performance of a LiNbO/sub 3/ optical modulator and switch, which employ superconducting circuits, have been studied. Based on a novel design method of the booster circuit using superconducting coplanar waveguide transmission lines, we designed a voltage amplifier with center frequency of 10 GHz, bandwidth of 5 MHz, and the voltage gain of 33 dB using an electromagnetic wave simulator. We also designed a high speed optical switch combining optical directional coupler and Mach-Zehnder interferometer. A preliminary experiment with YBCO electrode on MgO substrate flip-chip-bonded on LiNbO/sub 3/ optical waveguide has been made.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•10 citations

Theory of multiwave mixing within the superconducting kinetic-inductance traveling-wave amplifier

Robert P. Erickson, David P. Pappas

Traveling-wave parametric amplifiers may be fabricated from superconducting films that exhibit highly nonlinear kinetic inductance. The coplanar waveguide of such a microwave device, extending to a meter or more in length but compacted to reside on a chip of the order of a square centimeter, is engineered with periodic variations in its width. These width variations, or loadings, alter the dispersion characteristics of a nonlinear current propagating along the waveguide, changing its group velocity and modulation behavior. A strong pump and a small signal injected into one end of the waveguide mix parametrically in the presence of the nonlinear kinetic inductance. Engineered dispersion induces the favorable conditions of overall phase matching, leading to generation of idler products as well as signal amplification of wide bandwidth, high dynamic range, and low noise, making the device of particular use in quantum computing and photon detection. The authors present a theoretical framework in which signal gain may be calculated solely from loading design. This involves construction of a metamaterial band theory of the engineered dispersion, which is used as a basis to describe the mixing of nonlinear traveling waves.

arXiv:1612.00365•Physical review. B./Physical review. B•Mar 6, 2017•38 citations

Theory of Superconductive Traveling-Wave Photodetectors

Behnood G. Ghamsari, A. Hamed Majedi

This paper studies the theory of traveling-wave photodetection in superconductive multilayer optical waveguides, as a general platform for ultrafast, ultrasensitive, and ultralow-noise optoelectronics. The kinetic inductance theory of superconductive thin films and the modified transmission line theory are employed to investigate the distributed photodetection and signal generation mechanisms in superconductive traveling-wave devices. A general model for calculation of the optical responsivity of superconductive traveling-wave photodetectors is developed and operation regimes of interest are highlighted. Moreover, the inclusion of a photoconductive layer in the device structure and some important loading schemes are discussed and their effects on the device performance, such as quantum efficiency and electrical bandwidth, are addressed.

IEEE Transactions on Applied Superconductivity•Dec 1, 2008•13 citations

Experimental Characterization of Optically Tunable High-Temperature Superconducting Microwave Resonators and Delay Lines

Haig A. Atikian, Behnood G. Ghamsari, A. Hamed Majedi

This paper reports the design, fabrication, and measurements of optically tunable superconducting microwave resonators and delay lines. The devices are comprised of superconducting coplanar waveguide (CPW) transmission lines fabricated from a 100 nm-thick YBCO film, interrupted by 3- and 5-m YBCO meander structures of the same thickness on top of an LAO substrate. The CPW is tested at 77 K up to a frequency of 50 GHz, where it exhibits a transmission loss of about 0.12 dB/mm. The measurements are done in a cryogenic microwave probe station, where all the calibrations have been performed at 77 K. It has been observed that the resonance frequencies of the superconducting resonators can be changed by more than 2 GHz under the optical illumination at a wavelength of 1550 nm. The delay lines also exhibit a phase retardation of up to 90 at the same operating conditions.

IEEE Transactions on Microwave Theory and Techniques•Oct 27, 2010•13 citations

Evaluation of Attenuation Constants of Superconducting NbN Coplanar Waveguides

Hirotake Yamamori, Akira Shoji

Attenuation constants of superconducting NbN coplanar waveguides (CPWs) have been evaluated by measuring their transmission coefficients and reflection coefficients with a network analyzer. It has been found that the attenuation constant of NbN CPWs rapidly increases when their thicknesses are reduced below the penetration depth (300 nm). It has also been found that the experimentally measured attenuation constants of NbN CPWs coincide well with the numerically calculated ones.

Japanese Journal of Applied Physics•Jul 1, 2005•1 citation

Broadband tuneable travelling wave parametric multiplier based on high-gap superconducting thin film

Boon-Kok Tan, Nikita S. Klimovich, Peter K. Day

The well-established technology of the superconducting quantum parametric amplifier (SPA) can be reconfigured to perform functions beyond amplification, such as frequency multiplication, by utilising the low-noise, low-loss superconducting nonlinear transmission line. This versatile technology holds potential for various applications, including ‘pumping’ a millimetre (mm) or sub-mm wave heterodyne mixer or driving a high-frequency SPA. Its significance lies in the ability to incorporate a high-purity signal source into the cryogenic stage alongside the primary detector, thereby eliminating noise associated with room temperature sources. Additionally, there is potential for on-chip integration with the detector circuit, leading to a more compact architecture. This manuscript details the design of a travelling-wave parametric multiplier (TWPaM) that exploits the nonlinear wave-mixing mechanism to enhance the third harmonic growth from a strong pump tone injected into the travelling wave parametric amplifier (TWPA)-like device. While this functionality has been demonstrated previously, it exhibited narrowband performance. In this manuscript, we present our approach to designing a dispersion engineering scheme that enables the generation of broadband tunable tripler tones with high conversion efficiency. We showcase our design methodology using a niobium titanium nitride (NbTiN) high-gap thin-film transmission line as an example. Our presentation includes the theoretical model governing the physics of higher harmonics generation, emphasising phase-matching conditions that allow for broadband operation while suppressing unwanted modes. Although the ultimate aim is to develop a mm/sub-mm TWPaM, we aim to demonstrate the feasibility of their operation with a scaled microwave design in this manuscript. We will show that we can theoretically achieve close to 35% conversion efficiency across approximately 60% operational bandwidth.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jun 14, 2024•0 citations
The performance of a LiNbO/sub 3/ optical modulator employing superconducting electrodes as a transmission line for a traveling-wave signal has been studied theoretically as well as experimentally. In the case of velocity matching between signal and optical waves using a shielding plane on top of a coplanar waveguide, numerical calculations of the attenuation constants of both superconducting and normal-conducting transmission lines indicate that the performance of the optical modulator can be far superior to that using normal-metals with respect to the figure of merit of bandwidth/driving-voltage. Microwave operation of a velocity-matched traveling-wave-type optical modulator with superconductor electrodes (NbN) has been successfully demonstrated. In the frequency range between dc and 26.5 [GHz] it is shown that the obtained modulation depth is in good agreement with the theoretically expected one.
The design and performance of a LiNbO/sub 3/ optical modulator and switch, which employ superconducting circuits, have been studied. Based on a novel design method of the booster circuit using superconducting coplanar waveguide transmission lines, we designed a voltage amplifier with center frequency of 10 GHz, bandwidth of 5 MHz, and the voltage gain of 33 dB using an electromagnetic wave simulator. We also designed a high speed optical switch combining optical directional coupler and Mach-Zehnder interferometer. A preliminary experiment with YBCO electrode on MgO substrate flip-chip-bonded on LiNbO/sub 3/ optical waveguide has been made.
Traveling-wave parametric amplifiers may be fabricated from superconducting films that exhibit highly nonlinear kinetic inductance. The coplanar waveguide of such a microwave device, extending to a meter or more in length but compacted to reside on a chip of the order of a square centimeter, is engineered with periodic variations in its width. These width variations, or loadings, alter the dispersion characteristics of a nonlinear current propagating along the waveguide, changing its group velocity and modulation behavior. A strong pump and a small signal injected into one end of the waveguide mix parametrically in the presence of the nonlinear kinetic inductance. Engineered dispersion induces the favorable conditions of overall phase matching, leading to generation of idler products as well as signal amplification of wide bandwidth, high dynamic range, and low noise, making the device of particular use in quantum computing and photon detection. The authors present a theoretical framework in which signal gain may be calculated solely from loading design. This involves construction of a metamaterial band theory of the engineered dispersion, which is used as a basis to describe the mixing of nonlinear traveling waves.
This paper studies the theory of traveling-wave photodetection in superconductive multilayer optical waveguides, as a general platform for ultrafast, ultrasensitive, and ultralow-noise optoelectronics. The kinetic inductance theory of superconductive thin films and the modified transmission line theory are employed to investigate the distributed photodetection and signal generation mechanisms in superconductive traveling-wave devices. A general model for calculation of the optical responsivity of superconductive traveling-wave photodetectors is developed and operation regimes of interest are highlighted. Moreover, the inclusion of a photoconductive layer in the device structure and some important loading schemes are discussed and their effects on the device performance, such as quantum efficiency and electrical bandwidth, are addressed.
This paper reports the design, fabrication, and measurements of optically tunable superconducting microwave resonators and delay lines. The devices are comprised of superconducting coplanar waveguide (CPW) transmission lines fabricated from a 100 nm-thick YBCO film, interrupted by 3- and 5-m YBCO meander structures of the same thickness on top of an LAO substrate. The CPW is tested at 77 K up to a frequency of 50 GHz, where it exhibits a transmission loss of about 0.12 dB/mm. The measurements are done in a cryogenic microwave probe station, where all the calibrations have been performed at 77 K. It has been observed that the resonance frequencies of the superconducting resonators can be changed by more than 2 GHz under the optical illumination at a wavelength of 1550 nm. The delay lines also exhibit a phase retardation of up to 90 at the same operating conditions.
The well-established technology of the superconducting quantum parametric amplifier (SPA) can be reconfigured to perform functions beyond amplification, such as frequency multiplication, by utilising the low-noise, low-loss superconducting nonlinear transmission line. This versatile technology holds potential for various applications, including ‘pumping’ a millimetre (mm) or sub-mm wave heterodyne mixer or driving a high-frequency SPA. Its significance lies in the ability to incorporate a high-purity signal source into the cryogenic stage alongside the primary detector, thereby eliminating noise associated with room temperature sources. Additionally, there is potential for on-chip integration with the detector circuit, leading to a more compact architecture. This manuscript details the design of a travelling-wave parametric multiplier (TWPaM) that exploits the nonlinear wave-mixing mechanism to enhance the third harmonic growth from a strong pump tone injected into the travelling wave parametric amplifier (TWPA)-like device. While this functionality has been demonstrated previously, it exhibited narrowband performance. In this manuscript, we present our approach to designing a dispersion engineering scheme that enables the generation of broadband tunable tripler tones with high conversion efficiency. We showcase our design methodology using a niobium titanium nitride (NbTiN) high-gap thin-film transmission line as an example. Our presentation includes the theoretical model governing the physics of higher harmonics generation, emphasising phase-matching conditions that allow for broadband operation while suppressing unwanted modes. Although the ultimate aim is to develop a mm/sub-mm TWPaM, we aim to demonstrate the feasibility of their operation with a scaled microwave design in this manuscript. We will show that we can theoretically achieve close to 35% conversion efficiency across approximately 60% operational bandwidth.