Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Controlling the Interface Properties of Submicrometric Nb/A– $\hbox{AlO}_{\rm x}$–Nb Josephson Junctions

V. Lacquaniti, Natascia De Leo, Matteo Fretto, Cristina Cassiago, Roberto Rocci, A. Sosso, Mikhail A. Belogolovskii

Published Nov 7, 2014• 4 citations
Publisher

Abstract

Submicron Josephson devices are of a particular interest to the emerging field of quantum information, nanosized superconducting quantum interference devices (nano-SQUID) fabrication, AC voltage synthesis circuits for quantum metrology, etc. In this paper, we report on the development of our technology for producing non-hysteretic Nb/A-AlOx-Nb four-layered junctions with a diverse range of submicron dimensions, based on the focused ion beam (FIB) sculpting technique. We observed essential modifications of the main electrical characteristics as a result of the shrinking of the junction area, and relate them to the changes of the buried Nb/Al interface. We show that the electrical parameters-versus-temperature dependence can provide information on the quality of the junction interfaces. This aspect could be useful to better control of the entire fabrication process, allowing a further large-scale integration of Josephson nanodevices with improved transport characteristics.

DOI
10.1109/tasc.2014.2367232

Related papers

Transport properties of nanoscale Nb and NbN Josephson junctions fabricated by focused-ion-beam milling

Kazuaki Matsuba, 道生 渡部, Jaw-Shen Tsai

We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.

Journal of Applied Physics•Apr 1, 2008•2 citations

Realization of superconducting quantum devices based on tunnel Josephson junctions by micro and nanofabrication techniques

Maria De Leo

This PhD Thesis is focused on the realization of superconducting quantum devices based on overdamped Nb/Al-AlOx/Nb SNIS (Superconductor - Normal metal - Insulator - Superconductor) tunneling Josephson junctions, interesting for several application fields (voltage metrology, digital electronics, radiation sensors, nanoSQUID, etc.). The challenges faced by quantum electronics and metrology are directing the new generations of devices towards smaller dimensions and higher levels of integration. Taking into account this requirement, the fabrication of SNIS-based devices has been addressed on downscaling the junction dimensions form the micro to the nanoscale. In particular, the effective area of junctions has been reduced exploiting three different lithographic techniques: the optical lithography to realize SNISs for a micrometer resolution, the Electron Beam Lithography (EBL) at the subµm and, finally, the Focused Ion Beam (FIB) sculpting method to achieve nanometer sizes. Specifically, prototypes have been realized exploiting the thin film technology, to guarantee a good control of electrical parameters of junctions, a higher reproducibility of their current-voltage I-V characteristics, and an accurate dimension control. Reliable and simpler fabrication processes have been implemented and validated, and the device downscaling was pursued without affecting the fundamental properties of SNIS junctions such as the non hysteretic I-V response and the skill on generating quantised voltage steps under radiofrequency irradiation. This work has thereby led to the definition and validation of a new generation of devices and processes down to the nanometer scale, and these approaches represent precious experiences of nanofabrication valuable for new research activities and projects

•Jan 1, 2013•0 citations

Sub-Micron SNIS Josephson Junctions for Metrological Application

Natascia De Leo, Matteo Fretto, A. Sosso +3 more

The overdamped Nb/Al-AlOx/Nb superconductor-normal metal-insulator-superconductor SNIS Josephson junctions recently developed at INRIM exhibit high values of critical current density and characteristic voltage, making these devices appealing both for metrology and digital electronics. High current densities could allow reduction of junction size, increasing the integration level. In this work authors present first results concerning the realization of sub-μm SNIS including a nanolithographic technique (Electron Beam Lithography, EBL) into the conventional process, to reduce junction dimensions. Fabrication and electrical parameters have been evaluated considering the scaling of the areas of junctions, furthermore RF and temperature behaviour have been studied.

Physics Procedia•Jan 1, 2012•4 citations

Fabrication and characterization of high-quality Nb/Al-AlO x /Nb cross-type Josephson tunnel junctions utilising CMP-based planarisation techniques

Alexander Stoll, Andreas Reifenberger, Daniel Hengstler +2 more

Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.

arXiv:2609.08569•Superconductor Science and Technology•Nov 10, 2026•0 citations

Fabrication of Nb/Al(AlOx)/Nb DC SQUID by focused ion beam sculpturing

Yuvaraj, D., Gil Bachar, Oren Suchoi +2 more

Highly reproducible Nb/Al(AlOx)/Nb Josephson junction based direct current superconducting quantum interference devices (DC SQUID) were fabricated by three dimensional etching using focused ion beam. Hysteretic and non-hysteretic DC SQUID with critical current ranging from 25 to 1100 microampere were fabricated by varying the Al barrier and oxygen exposure time. The fabricated DC SQUIDs have shown periodic flux dependence with high modulation factor reaching a value of 92% at 4.2 K.

arXiv:1107.0635•Jul 4, 2011•4 citations

Characteristics of focused ion beam nanoscale Josephson devices

L Hao, David Cox, John C. Gallop

The requirements of quantum metrology and nanoscience are driving the need for single-particle detection capability across a wide variety of physics areas, including quantum information processing, single-photon detection, nanoelectromechanical systems, nanomagnetism and spintronics. The single particles to be detected include atoms, molecules, photons, spins and even phonons, in the future. Nanoscale superconducting quantum interference devices (nanoSQUIDs) represent a new manifestation of an old but exciting superconducting technology which addresses some of these requirements. In this paper we describe a straightforward approach to fabricating Nb microbridge weak links using combined optical lithography and focused ion beams which may be used to fabricate nanoSQUIDs. The devices show non-hysteretic current?voltage characteristics and demonstrate very low noise, even at operating temperatures above 4.2?K. To improve our understanding of the superconducting properties of the Josephson microbridge/nanobridge junctions which have proved very successful in realizing low noise nanoSQUIDs we have carried out a combination of investigations. These include cryogenic resistance versus temperature (R(T)) and current?voltage characteristic measurements, atomic force microscope scans, controlled gallium (Ga) ion milling and implantation, and ion beam track modelling of these Josephson devices and Nb thin films.

Superconductor Science and Technology•May 14, 2009•22 citations
Controlling the Interface Properties of Submicrometric Nb/A– AlOx\hbox{AlO}_{\rm x}AlOx​–Nb Josephson Junctions
Submicron Josephson devices are of a particular interest to the emerging field of quantum information, nanosized superconducting quantum interference devices (nano-SQUID) fabrication, AC voltage synthesis circuits for quantum metrology, etc. In this paper, we report on the development of our technology for producing non-hysteretic Nb/A-AlOx-Nb four-layered junctions with a diverse range of submicron dimensions, based on the focused ion beam (FIB) sculpting technique. We observed essential modifications of the main electrical characteristics as a result of the shrinking of the junction area, and relate them to the changes of the buried Nb/Al interface. We show that the electrical parameters-versus-temperature dependence can provide information on the quality of the junction interfaces. This aspect could be useful to better control of the entire fabrication process, allowing a further large-scale integration of Josephson nanodevices with improved transport characteristics.
We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.
This PhD Thesis is focused on the realization of superconducting quantum devices based on overdamped Nb/Al-AlOx/Nb SNIS (Superconductor - Normal metal - Insulator - Superconductor) tunneling Josephson junctions, interesting for several application fields (voltage metrology, digital electronics, radiation sensors, nanoSQUID, etc.). The challenges faced by quantum electronics and metrology are directing the new generations of devices towards smaller dimensions and higher levels of integration. Taking into account this requirement, the fabrication of SNIS-based devices has been addressed on downscaling the junction dimensions form the micro to the nanoscale. In particular, the effective area of junctions has been reduced exploiting three different lithographic techniques: the optical lithography to realize SNISs for a micrometer resolution, the Electron Beam Lithography (EBL) at the subµm and, finally, the Focused Ion Beam (FIB) sculpting method to achieve nanometer sizes. Specifically, prototypes have been realized exploiting the thin film technology, to guarantee a good control of electrical parameters of junctions, a higher reproducibility of their current-voltage I-V characteristics, and an accurate dimension control. Reliable and simpler fabrication processes have been implemented and validated, and the device downscaling was pursued without affecting the fundamental properties of SNIS junctions such as the non hysteretic I-V response and the skill on generating quantised voltage steps under radiofrequency irradiation. This work has thereby led to the definition and validation of a new generation of devices and processes down to the nanometer scale, and these approaches represent precious experiences of nanofabrication valuable for new research activities and projects
The overdamped Nb/Al-AlOx/Nb superconductor-normal metal-insulator-superconductor SNIS Josephson junctions recently developed at INRIM exhibit high values of critical current density and characteristic voltage, making these devices appealing both for metrology and digital electronics. High current densities could allow reduction of junction size, increasing the integration level. In this work authors present first results concerning the realization of sub-μm SNIS including a nanolithographic technique (Electron Beam Lithography, EBL) into the conventional process, to reduce junction dimensions. Fabrication and electrical parameters have been evaluated considering the scaling of the areas of junctions, furthermore RF and temperature behaviour have been studied.
Abstract Josephson tunnel junctions (JJs) are the fundamental building blocks of today's most advanced superconducting electronic components, such as qubits and superconducting quantum interference devices (SQUIDs). Given the ongoing demand for scalability of these devices on the wafer-scale, it is crucial to control the fabrication process as precisely as possible to ensure uniform quality and reproducibility. Today, window-type JJs are often used in the production of DC SQUIDs and while they are reliable and reproducible, they suffer from alignment inaccuracies caused by photolithography and unavoidable parasitic capacitances, thus limiting the energy sensitivity of DC SQUIDs. These problems can be circumvented by producing JJs with cross-type geometry, which allows for smaller junction areas and eliminates parasitic capacitances. Here we discuss the fabrication of Nb/Al-AlO x /Nb-based cross-type JJs, where the trilayer is embedded in sputter-deposited SiO 2 to allow for planarisation of structures and to ensure reliable insulation of the sidewalls of the bottom electrode. Instead of lift-off processes that can require processing times of several hours and potentially produce residual dielectric features along the structure edges that might compromise subsequent layers, we use chemical-mechanical polishing (CMP) for the removal of excess SiO 2 . This reduces the duration of the planarization step from hours to minutes and yields smooth, uniform surfaces with a within-wafer non-uniformity of below 5%. The resulting process achieves a junction yield above 90% across 3 inch wafers. In addition, we discuss the influence of fabrication details on the quality and electrical properties of our JJs with different junction areas down to 1 µm × 1 µm distributed across the wafer and extract the junction specific quality parameters from their IV -characteristics. Across the junctions, the spreads are approximately 1% for gap voltage, below 3% for critical current, below 4% for the subgap-to-normal resistance ratio, and below 1% for characteristic voltage.
The requirements of quantum metrology and nanoscience are driving the need for single-particle detection capability across a wide variety of physics areas, including quantum information processing, single-photon detection, nanoelectromechanical systems, nanomagnetism and spintronics. The single particles to be detected include atoms, molecules, photons, spins and even phonons, in the future. Nanoscale superconducting quantum interference devices (nanoSQUIDs) represent a new manifestation of an old but exciting superconducting technology which addresses some of these requirements. In this paper we describe a straightforward approach to fabricating Nb microbridge weak links using combined optical lithography and focused ion beams which may be used to fabricate nanoSQUIDs. The devices show non-hysteretic current?voltage characteristics and demonstrate very low noise, even at operating temperatures above 4.2?K. To improve our understanding of the superconducting properties of the Josephson microbridge/nanobridge junctions which have proved very successful in realizing low noise nanoSQUIDs we have carried out a combination of investigations. These include cryogenic resistance versus temperature (R(T)) and current?voltage characteristic measurements, atomic force microscope scans, controlled gallium (Ga) ion milling and implantation, and ion beam track modelling of these Josephson devices and Nb thin films.