Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Large Signal Amplitude and Bias Range of Cascade Switch Superconducting Nanowire Single Photon Detectors

Mikkel Ejrnaes, A. Casaburi, Orlando Quaranta, S. Marchetti, Alessandro Gaggero, F. Mattioli, Roberto Leoni, S. Pagano, Roberto Cristiano

Published Jun 1, 2009• 8 citations
Publisher

Abstract

Cascade switch superconducting nanowire single photon detectors has been fabricated of ultrathin NbN films deposited by DC-magnetron sputtering at room temperature on MgO substrates. Detectors using 4 to 24 nanowires in parallel, having an area coverage of 5times mum2and a filling factor of 40%, have been investigated. Signal amplitudes increase with the number of parallel nanowires and reaches 12.3 mV with a signal noise of 20 muV. The range of bias currents where the detectors emit signal pulses also increase with the number of parallel nanowires and exceeds the nanowire critical current.

DOI
10.1109/tasc.2009.2019034

Related papers

Superconducting single photon detectors based on parallel NbN nanowires

Mikkel Ejrnaes, A. Casaburi, S. Pagano +4 more

Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 29, 2011•0 citations

A cascade switching superconducting single photon detector

Mikkel Ejrnaes, Roberto Cristiano, Orlando Quaranta +6 more

We have realized superconducting single photon detectors with reduced inductance and increased signal pulse amplitude. The detectors are based on a parallel connection of ultrathin NbN nanowires with a common bias inductance. When properly biased, an absorbed photon induces a cascade switch of all the parallel wires generating a signal pulse amplitude of 2mV. The parallel wire configuration lowers the detector inductance and reduces the response time well below 1ns.

Applied Physics Letters•Dec 24, 2007•122 citations

Superconducting single photon detectors based on multiple cascade switches of parallel NbN nanowires

Roberto Cristiano, Mikkel Ejrnaes, A. Casaburi +4 more

Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 30, 2011•2 citations

High efficiency NbN nanowire superconducting single photon detectors fabricated on MgO substrates from a low temperature process

Francesco Marsili, David Bitauld, Andrea Fiore +5 more

We demonstrate high-performance nanowire superconducting single photon detectors (SSPDs) on bN thin films grown at a temperature compatible with monolithic integration. NbN films ranging from 150 nm to 3 nm in thickness were deposited by dc magnetron sputtering on MgO substrates at 400 degrees C SSPDs were fabricated on high quality NbN films of different thickness (7 to 3 nm) deposited under optimal conditions. Electrical and optical characterizations were performed on the SSPDs. The highest QE value measured at 4.2K is 20% at 1300 nm.

arXiv:0712.3295•Optics Express•Jan 1, 2008•64 citations

NbN nanowire superconducting single photon detectors fabricated on MgO substrates

Francesco Marsili, David Bitauld, Alessandro Gaggero +6 more

High sensitivity ultrafast nanowire superconducting single photon detectors (SSPD) in the near infrared wavelength range have been fabricated with ultrathin (3.5nm) NbN films grown on R-plane sapphire substrates by dc reactive magnetron sputtering in Ar+N2mixture. These results show for the first time that high performance NbN SSPDs can be realized on different substrates and at lower deposition temperature than previously reported, and opens the way to integration with advanced solid state optical structures. SSPDs have been fabricated by a two mask process using electron beam lithography and reactive ion etching on 3.5nm thick NbN films deposited under optimal conditions on MgO.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2007•0 citations

Large sensitive-area NbN nanowire superconducting single-photon detectors fabricated on single-crystal MgO substrates

Shigehito Miki, Mikio Fujiwara, Masahide Sasaki +5 more

We report on the performance of large area NbN nanowire superconducting single-photon detectors (SSPDs). 20×20μm2 area SSPDs with 80 and 100nm linewidths and 50% fill factor were fabricated in 4-nm-thick NbN films grown on single-crystal MgO substrates. The high quality of the devices was verified by electrical and optical testing and compares favorably to measurements of 10×10μm2 area SSPDs. Measurements of kinetic inductance versus bias current indicate that the constriction density is low. The fiber-coupled detection efficiency of the devices was 0.4%–3.5% at 100Hz dark count rate.

Applied Physics Letters•Feb 11, 2008•119 citations
Cascade switch superconducting nanowire single photon detectors has been fabricated of ultrathin NbN films deposited by DC-magnetron sputtering at room temperature on MgO substrates. Detectors using 4 to 24 nanowires in parallel, having an area coverage of 5times mum2and a filling factor of 40%, have been investigated. Signal amplitudes increase with the number of parallel nanowires and reaches 12.3 mV with a signal noise of 20 muV. The range of bias currents where the detectors emit signal pulses also increase with the number of parallel nanowires and exceeds the nanowire critical current.
Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.
Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation.
We demonstrate high-performance nanowire superconducting single photon detectors (SSPDs) on bN thin films grown at a temperature compatible with monolithic integration. NbN films ranging from 150 nm to 3 nm in thickness were deposited by dc magnetron sputtering on MgO substrates at 400 degrees C SSPDs were fabricated on high quality NbN films of different thickness (7 to 3 nm) deposited under optimal conditions. Electrical and optical characterizations were performed on the SSPDs. The highest QE value measured at 4.2K is 20% at 1300 nm.
High sensitivity ultrafast nanowire superconducting single photon detectors (SSPD) in the near infrared wavelength range have been fabricated with ultrathin (3.5nm) NbN films grown on R-plane sapphire substrates by dc reactive magnetron sputtering in Ar+N2mixture. These results show for the first time that high performance NbN SSPDs can be realized on different substrates and at lower deposition temperature than previously reported, and opens the way to integration with advanced solid state optical structures. SSPDs have been fabricated by a two mask process using electron beam lithography and reactive ion etching on 3.5nm thick NbN films deposited under optimal conditions on MgO.
We report on the performance of large area NbN nanowire superconducting single-photon detectors (SSPDs). 20×20μm2 area SSPDs with 80 and 100nm linewidths and 50% fill factor were fabricated in 4-nm-thick NbN films grown on single-crystal MgO substrates. The high quality of the devices was verified by electrical and optical testing and compares favorably to measurements of 10×10μm2 area SSPDs. Measurements of kinetic inductance versus bias current indicate that the constriction density is low. The fiber-coupled detection efficiency of the devices was 0.4%–3.5% at 100Hz dark count rate.