Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Instrumentation and Measurement

All-niobium process for Josephson series array circuits

Se Il Park, Kyu‐Tae Kim, Rae Duk Lee

Published Apr 1, 1995• 7 citations
Publisher

Abstract

We have developed a new fabrication process for integrated Nb/Al/sub 2/O/sub 3//Nb Josephson series arrays using the selective niobium anodization process (SNAP), the image reversal technique (IRT) and lift-off. To avoid chaotic behavior, the critical current of the array was decreased by post-fabrication annealing or the in situ multilayer oxidation process. In the frequency range 70-100 GHz, the array containing 2520 junctions produced stable quantized voltage steps up to 2 V with step widths of 40-100 /spl mu/A and stability times of more than 4 h.>

DOI
10.1109/19.377821

Related papers

A high quality 1-V Josephson series array developed at KRISS

Se II Park, Kyu‐Tae Kim, Rae Duk Lee

By combining the selective niobium anodization process (SNAP) and the image reversal technique (IRT) a new fabrication process of integrated Josephson series array has been developed at KRISS. The array containing 2520 Nb/Al/sub 2/O/sub 3//Nb tunnel junctions produced stable quantized voltage steps up to 2 V with stability times of more than 5-h.>

Conference on Precision Electromagnetic Measurements•Dec 17, 2002•0 citations

Development of Nb/Al-oxide/Nb Josephson junction array at KRISS (voltage standard)

Se II Park, Kyu-Tae Kim, Yong Ho Lee +1 more

By using the selective niobium anodization process (SNAP) an all refractory 210-junction array was fabricated at KRISS. The array consists of Nb/Al-oxide/Nb junctions that have A=20 mu m*40 mu m. V/sub g/=2.8 mV, an average critical current approximately=650 mu A, and the spread of critical currents approximately=+or-5%. When operated at 94 GHz, the array generated zero-crossing steps up to 240 mV with stability times of more than 1 h.>

IEEE Transactions on Instrumentation and Measurement•Apr 1, 1993•5 citations

Development and investigation of Nb-Al-oxide-Nb Josephson junction arrays [voltage standard application]

A.F. Bochanov, V.D. Gelikonova, Alexander M. Klushin +2 more

An array of 3072 Josephson junctions Nb-AlO/sub x/-Nb is developed at IEM "KVARZ". Some preliminary results of an investigation of I-V curves under microwave irradiation in the 70 GHz frequency band are given. Zero current quantized voltage steps are displayed up to 450 mV with an amplitude >100 /spl mu/A. An improvement of the fabrication process, which is in progress, will enable to increase quantized voltage steps region up to 1 V.>

Conference on Precision Electromagnetic Measurements•Dec 17, 2002•0 citations

Development and investigation of Nb-Al-oxide-Nb Josephson Junction arrays

A.F. Bochanov, V.D. Gelikonova, Alexander M. Klushin

An array of 3072 Josephson junctions Nb - AlO{sub x} - Nb is developed at IEM {open_quotes}KVARZ{close_quotes}. Some preliminary results of an investigation of IV curves under microwave irradiation in the 70 GHz frequency band are given. Zero current quantized voltage steps are displayed up to 450 mV with an amplitude > 100 {mu}A. An improvement of the fabrication process, which is in progress, will enable to increase quantized voltage steps region up to IV.

•Dec 31, 1994•0 citations

Nb/AlOx/Nb Josephson Tunnel Junctions Using Electron Beam Evaporation

Atsuki Inoue, Akiyoshi Nakayama, Yoichi Okabe

Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.

Japanese Journal of Applied Physics•Jul 1, 1988•10 citations

SNAP structures with Nb-AlO/sub x/-Nb junctions for MM-wave receivers

An. B. Ermakov, V. P. Koshelets, I. L. Serpuchenko +3 more

High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>

IEEE Transactions on Magnetics•Mar 1, 1989•7 citations
We have developed a new fabrication process for integrated Nb/Al/sub 2/O/sub 3//Nb Josephson series arrays using the selective niobium anodization process (SNAP), the image reversal technique (IRT) and lift-off. To avoid chaotic behavior, the critical current of the array was decreased by post-fabrication annealing or the in situ multilayer oxidation process. In the frequency range 70-100 GHz, the array containing 2520 junctions produced stable quantized voltage steps up to 2 V with step widths of 40-100 /spl mu/A and stability times of more than 4 h.>
Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.
High-quality small-area Nb-AlO/sub x/-Nb junctions have been fabricated by the selective niobium anodization process (SNAP). The influence of the preparation conditions on the junction properties were investigated. Numerical calculations based on I-V (current-voltage) characteristics measured by a data acquisition system were used to simulate the mixer performance. It has been shown that the knee-shaped structure on the I-V curve of refractory material junctions significantly affects the signal properties of the mixer. The signal and noise properties for different types of integrated SIS (superconductor-insulator-superconductor) mixing elements have been investigated experimentally in the frequency range of 37-53 GHz; the mixer conversion loss was as low as 4 dB at 45 GHz. The mixing elements consist of an odd number of SIS junctions connected in series for RF and in parallel for DC biasing. The DC bias wiring and IF (intermediate frequency) filters of these structures were designed to provide tuning out of junction capacitance and thin-film-electrode inductance.>