Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Circuits

RSFQ DC to SFQ converter with reduced Josephson current density

Valeri Mladenov

Published Jul 23, 2007• 0 citations
OpenAlex

Abstract

Abstract:- In this paper we consider the Rapid Single-Flux Quantum (RSFQ) circuits with reduced Josephson current density and especially deal with one of the basic building blocks of these electronics- the DC to SFQ converter. For future promising RSFQ applications the critical current of the Josephson junctions should be reduced (by reduction of Josephson current density) to several µA, resulting into values of the interferometer’s inductance of several hundreds of pH. Such large inductances cannot be efficiently realized and we utilize an approach for substitution of inductances by arrays of classical Josephson junctions operating in nonswitching mode. We investigate the classical DC to SFQ converter and based on the utilized approach we design a new schematic with reduced Josephson current density. The circuit is optimized with respect to yield and fabrication margins of the design parameters. Key-Words:- Superconductivity, Rapid Single-Flux Quantum (RSFQ) electronics, Josephson junction, DC to SFQ converter. 1

Related papers

Phase-Drop Realization Within RSFQ Digital Circuits With Reduced Josephson Current Density

Boyko Dimov, Thomas Ortlepp, Friedrich Uhlmann

Within the classical Rapid Single-Flux Quantum (RSFQ) digital designs, the superconductive phase dropping necessary for the optimal SFQ data processing is realized with short sections of transmission lines serving as lumped inductances. This approach meets several hard restrictions about some promising future RSFQ applications requiring a drastic reduction of the junctions' critical currents. In this paper, we analyse these restrictions, and present an alternative and experimentally verified technique for superconductive phase dropping, which is compatible with any RSFQ fabrication technology. This technique provides compact and robust RSFQ digital circuits with highly improved fabrication yield.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•4 citations

SFQ Bias for SFQ Digital Circuits

Vasili K. Semenov, Evan B. Golden, Sergey K. Tolpygo

Superconductor electronics fabrication technology developed at MIT Lincoln Laboratory enables the development of VLSI digital circuits with millions of Josephson junctions per square centimeter. However, conventional DC and multi-phase AC biasing techniques already encounter serious challenges for scaling circuits above several hundred thousand junctions. In this work, we propose a novel AC-based biasing scheme for RSFQ-type logic families requiring DC bias. The major step toward this scheme is a superconducting AC/DC rectifier which we introduced at ASC 2014. We proposed to connect the rectifiers to “payload cells” via superconducting inductors with large inductance in order to reduce parasitic effects of flux quantization. Recently, we discovered that this powering scheme works even better at a much lower value of the inductance, when it is just sufficient to hold only one or two flux quanta in the inductive loop between the converter and the payload. In this case, flux quantization in the loop becomes beneficial because the value of current fed into the payload is defined by the value of the coupling inductance. Therefore, our AC/SFQ converter powers the payload cell by single flux quanta rather than by DC current. Such mode of operation is extremely energy efficient because energy is used only to recover the flux quantum consumed by the cell during the logic operation. We present designs of AC/SFQ converters comprising an AC/DC rectifier and a current conditioning circuit which we termed an SFQ filter. We also present test results and demonstrate AC/SFQ powering a payload circuit using circuits fabricated in a new, 150-nm node of Lincoln Laboratory fabrication technology using self-shunted Nb/AlOx-Al/Nb Josephson junctions with 600 μA/μm2critical current density and 200 nm minimum linewidth of inductors.

arXiv:2012.12405•IEEE Transactions on Applied Superconductivity•Mar 18, 2021•15 citations

RSFQ circuitry realized in a SINIS technology process

M. Khabipov, D Balashov, F.-I. Buchholz +2 more

We have developed integrated circuits in rapid single flux quantum (RSFQ) impulse logic based on intrinsically shunted tunnel junctions as the active circuit elements. The circuits have been fabricated using superconductor-insulator-normalconductor-insulator-superconductor (SINIS) multilayer technology. The paper presents experimental results of the operation of various RSFQ circuits realized in different designs and layouts. The circuits comprise dc/SFQ and SFQ/dc converters, Josephson transmission lines (JTLs), T-flipflops, and analog key components. Functionality has been proved; the circuits have been found to operate correctly in switching. The circuits investigated have a critical current density of j/sub C/=400 A/cm/sup 2/ and a characteristic voltage of V/sub C/=165 /spl mu/V, the area of the smallest junction is A=24 /spl mu/m/sup 2/. The junctions exhibit nearly hysteresis-free current-voltage characteristics (hysteresis: less than 7%), the intra-wafer parameter spread for j/sub C/ is below /spl plusmn/8%. The margins of the bias current I/sub b/ of the circuits have been experimentally determined and found to be larger than /spl plusmn/24%. At preset, constant values of I/sub b/, the range of a separate bias current I/sub bsw/ fed to a switching stage integrated between two segments of JTL's is fully covered by the operation margins which are larger than /spl plusmn/56%.

IEEE Transactions on Applied Superconductivity•Jan 1, 1999•15 citations

Rapid single-flux quantum logic using π-shifters

Alexey Vladimirovich Ustinov, V. K. Kaplunenko

We have found that the size of some rapid single-flux quantum (RSFQ) logic cells based on conventional 0-type Josephson junctions can be significantly reduced by using a π-type junction as a phase shifter in passive (nonswitching) mode. In comparison with the recently suggested active (switching) π-junctions mode, the passive mode offers much greater operation margins for their critical current Icπ. This gives π-junctions a chance to be implemented in RSFQ designs in the near future. As an example, we have simulated the operation of a toggle flip flop with zero-geometrical inductance of the fluxon storage loop. Simulations show that the parametric inductance of the π-junction and its normal resistance Rn form a low-pass filter, which sets the low limit for π-junctions IcπRn product, but offers a wide range of variations of the other parameters. The possible reduction of RSFQ cell size by using π-junctions opens the way to scale superconducting logic circuits down to the submicron dimensions.

Journal of Applied Physics•Oct 3, 2003•131 citations

AC Biased SFQ Clock Splitters for Current Mitigation

Tejumadejesu Oluwadamilare, Eby G. Friedman

High current requirements in single flux quantum (SFQ) circuits pose scalability challenges, contributing to issues such as high thermal loads, static power dissipation, and increased sensitivity to flux trapping under non-ideal shielding or cool down conditions. AC biasing, successfully used in other superconductive logic families, has been integrated into rapid single flux quantum (RSFQ) circuits and typically includes AC-to-DC converters, introducing area and complexity overhead. This work proposes an alternative method for applying AC biasing to existing RSFQ circuits using inductively coupled bias junctions, eliminating the need for AC-to-DC converters. This approach also combines resistive DC biasing with inductive AC biasing, reducing static power dissipation. The proposed approach targets clock splitters, which are significant contributors to on-chip current demand, achieving an average 94% reduction in splitter current and a 62% reduction in overall system current with a Josephson junction overhead of 6.5%. The technique is compatible with conventional RSFQ system architectures and logic families while significantly enhancing energy efficiency and scalability.

IEEE Transactions on Applied Superconductivity•Nov 5, 2025•0 citations

Design and Fabrication of Low-Power Single-Flux-Quantum Circuits Toward Quantum Bit Control

Masamitsu Tanaka, Yoshihiro Kitagawa, T. Satoh +1 more

We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm$^{2}$to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.

IEEE Transactions on Applied Superconductivity•Mar 2, 2023•15 citations
Abstract:- In this paper we consider the Rapid Single-Flux Quantum (RSFQ) circuits with reduced Josephson current density and especially deal with one of the basic building blocks of these electronics- the DC to SFQ converter. For future promising RSFQ applications the critical current of the Josephson junctions should be reduced (by reduction of Josephson current density) to several µA, resulting into values of the interferometer’s inductance of several hundreds of pH. Such large inductances cannot be efficiently realized and we utilize an approach for substitution of inductances by arrays of classical Josephson junctions operating in nonswitching mode. We investigate the classical DC to SFQ converter and based on the utilized approach we design a new schematic with reduced Josephson current density. The circuit is optimized with respect to yield and fabrication margins of the design parameters. Key-Words:- Superconductivity, Rapid Single-Flux Quantum (RSFQ) electronics, Josephson junction, DC to SFQ converter. 1
Within the classical Rapid Single-Flux Quantum (RSFQ) digital designs, the superconductive phase dropping necessary for the optimal SFQ data processing is realized with short sections of transmission lines serving as lumped inductances. This approach meets several hard restrictions about some promising future RSFQ applications requiring a drastic reduction of the junctions' critical currents. In this paper, we analyse these restrictions, and present an alternative and experimentally verified technique for superconductive phase dropping, which is compatible with any RSFQ fabrication technology. This technique provides compact and robust RSFQ digital circuits with highly improved fabrication yield.
Superconductor electronics fabrication technology developed at MIT Lincoln Laboratory enables the development of VLSI digital circuits with millions of Josephson junctions per square centimeter. However, conventional DC and multi-phase AC biasing techniques already encounter serious challenges for scaling circuits above several hundred thousand junctions. In this work, we propose a novel AC-based biasing scheme for RSFQ-type logic families requiring DC bias. The major step toward this scheme is a superconducting AC/DC rectifier which we introduced at ASC 2014. We proposed to connect the rectifiers to “payload cells” via superconducting inductors with large inductance in order to reduce parasitic effects of flux quantization. Recently, we discovered that this powering scheme works even better at a much lower value of the inductance, when it is just sufficient to hold only one or two flux quanta in the inductive loop between the converter and the payload. In this case, flux quantization in the loop becomes beneficial because the value of current fed into the payload is defined by the value of the coupling inductance. Therefore, our AC/SFQ converter powers the payload cell by single flux quanta rather than by DC current. Such mode of operation is extremely energy efficient because energy is used only to recover the flux quantum consumed by the cell during the logic operation. We present designs of AC/SFQ converters comprising an AC/DC rectifier and a current conditioning circuit which we termed an SFQ filter. We also present test results and demonstrate AC/SFQ powering a payload circuit using circuits fabricated in a new, 150-nm node of Lincoln Laboratory fabrication technology using self-shunted Nb/AlOx-Al/Nb Josephson junctions with 600 μA/μm2critical current density and 200 nm minimum linewidth of inductors.
We have developed integrated circuits in rapid single flux quantum (RSFQ) impulse logic based on intrinsically shunted tunnel junctions as the active circuit elements. The circuits have been fabricated using superconductor-insulator-normalconductor-insulator-superconductor (SINIS) multilayer technology. The paper presents experimental results of the operation of various RSFQ circuits realized in different designs and layouts. The circuits comprise dc/SFQ and SFQ/dc converters, Josephson transmission lines (JTLs), T-flipflops, and analog key components. Functionality has been proved; the circuits have been found to operate correctly in switching. The circuits investigated have a critical current density of j/sub C/=400 A/cm/sup 2/ and a characteristic voltage of V/sub C/=165 /spl mu/V, the area of the smallest junction is A=24 /spl mu/m/sup 2/. The junctions exhibit nearly hysteresis-free current-voltage characteristics (hysteresis: less than 7%), the intra-wafer parameter spread for j/sub C/ is below /spl plusmn/8%. The margins of the bias current I/sub b/ of the circuits have been experimentally determined and found to be larger than /spl plusmn/24%. At preset, constant values of I/sub b/, the range of a separate bias current I/sub bsw/ fed to a switching stage integrated between two segments of JTL's is fully covered by the operation margins which are larger than /spl plusmn/56%.
We have found that the size of some rapid single-flux quantum (RSFQ) logic cells based on conventional 0-type Josephson junctions can be significantly reduced by using a π-type junction as a phase shifter in passive (nonswitching) mode. In comparison with the recently suggested active (switching) π-junctions mode, the passive mode offers much greater operation margins for their critical current Icπ. This gives π-junctions a chance to be implemented in RSFQ designs in the near future. As an example, we have simulated the operation of a toggle flip flop with zero-geometrical inductance of the fluxon storage loop. Simulations show that the parametric inductance of the π-junction and its normal resistance Rn form a low-pass filter, which sets the low limit for π-junctions IcπRn product, but offers a wide range of variations of the other parameters. The possible reduction of RSFQ cell size by using π-junctions opens the way to scale superconducting logic circuits down to the submicron dimensions.
High current requirements in single flux quantum (SFQ) circuits pose scalability challenges, contributing to issues such as high thermal loads, static power dissipation, and increased sensitivity to flux trapping under non-ideal shielding or cool down conditions. AC biasing, successfully used in other superconductive logic families, has been integrated into rapid single flux quantum (RSFQ) circuits and typically includes AC-to-DC converters, introducing area and complexity overhead. This work proposes an alternative method for applying AC biasing to existing RSFQ circuits using inductively coupled bias junctions, eliminating the need for AC-to-DC converters. This approach also combines resistive DC biasing with inductive AC biasing, reducing static power dissipation. The proposed approach targets clock splitters, which are significant contributors to on-chip current demand, achieving an average 94% reduction in splitter current and a 62% reduction in overall system current with a Josephson junction overhead of 6.5%. The technique is compatible with conventional RSFQ system architectures and logic families while significantly enhancing energy efficiency and scalability.
We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm2^{2}2to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.