An increase in bias currents supplied to single-flux-quantum (SFQ) circuits is a rising problem in building large-scale integrated SFQ circuits, because the magnetic fields generated by bias currents and ground return currents affect the circuit operation. Current recycling technique, which can drastically reduce the total bias current of SFQ circuits, is expected to be a very effective solution for large-scale SFQ circuits. To realize the current recycling technique, signal transmission between SFQ logic circuits located on different ground planes is required. Two types of inductively coupled pulse transfer circuits were examined in this study. One is composed of a simple JTL driver and a DC-SQUID receiver whose junctions are slightly under-damped to enhance the magnetic sensitivity of the SQUID. The other circuit is composed of an SFQ driver based on a delay flip-flop (DFF) and a SQUID receiver. The advantage of the DFF-based circuit is that the coupling time between the driver and the receiver can be increased to ensure appropriate switching in the receiver junction. Two types of transfer circuits were implemented using the SRL 2.5 kA/cm2Nb process and their correct operation was experimentally confirmed. Circuit structures for effective coupling of the SFQ pulse transfer were also investigated. It was shown that a ground plane boundary should be separated from a ground plane hole underneath coupling inductors to obtain high coupling factors.
An increase in bias currents supplied to single-flux-quantum (SFQ) circuits is a rising problem in building large-scale integrated SFQ circuits, because the magnetic fields generated by bias currents and ground return currents affect the circuit operation. Current recycling technique, which can drastically reduce the total bias current of SFQ circuits, is expected to be a very effective solution for large-scale SFQ circuits. To realize the current recycling technique, signal transmission between SFQ logic circuits located on different ground planes is required. Two types of inductively coupled pulse transfer circuits were examined in this study. One is composed of a simple JTL driver and a DC-SQUID receiver whose junctions are slightly under-damped to enhance the magnetic sensitivity of the SQUID. The other circuit is composed of an SFQ driver based on a delay flip-flop (DFF) and a SQUID receiver. The advantage of the DFF-based circuit is that the coupling time between the driver and the receiver can be increased to ensure appropriate switching in the receiver junction. Two types of transfer circuits were implemented using the SRL 2.5 kA/cm2Nb process and their correct operation was experimentally confirmed. Circuit structures for effective coupling of the SFQ pulse transfer were also investigated. It was shown that a ground plane boundary should be separated from a ground plane hole underneath coupling inductors to obtain high coupling factors.
The practical implementation of RSFQ technology in most digital electronics application areas requires much more complexity than the presently developed circuits. There are two important issues in building large-scale RSFQ circuits: 1) the recycling of the bias currents and 2) the transfer of SFQ pulses between circuits located far apart. RSFQ circuits are well known to operate with DC current bias. Even though the DC current biasing is more forgiving than the problematic AC biasing, it can still be a big concern when the circuit size becomes large. Dramatic reduction of the total bias current can be achieved by biasing several RSFQ circuits in series, where each circuit is positioned on a separate ground plane. In this work, we have used magnetically coupled Josephson transmission lines as inputs and outputs of an isolated shift register to show the feasibility of using the concept of serial biasing in current recycling. The circuit was simulated, fabricated with Nb technology, and tested at a temperature of 4.2 K. Test results show that SFQ pulses were transferred into the shift register built on a separate ground plane, clocked through it, and sent out back to the circuit on the original ground plane. We also studied on how to transfer SFQ pulses over an extended length, an important issue in building large RSFQ circuits. We have designed the circuits to test our microstrip line and multichip module approaches. We designed, optimized, fabricated and tested the circuits. Test results show that SFQ pulses can be successfully transmitted over an extensive distance in a chip and between chips.
Current recycling is an essential technique for realizing large-scale integrated single-flux-quantum circuits, since it can reduce bias current supply from several amperes to hundreds of milliamperes. Recently, there have been two reports proposing current recycling techniques. However, the fluctuation of global bias current, due to the switching of Josephson junctions, was not considered in these reports. Moreover, junctions cannot be grounded at the same point due to the use of isolated ground planes. In this paper, we propose a modified version of the current recycling technique using capacitive grounding, which will solve all these issues. We present an optimized driver and receiver for this technique. We have verified its workability and evaluated its characteristics by using several simulated tests, including evaluating bias set-up time, evaluating the relation of ground capacitance and signal capacitance to global bias margin, verifying its workability in a more complicated circuit, and performing high-speed test at frequencies up to 80 Gbps.
We propose an inductance-load-biasing method in order to reduce power consumption of rapid single flux quantum (SFQ) logic circuits. The main idea arises from the fact that a current source can be made of a large inductor accompanied by a large flux. In our proposal, the current source is composed of a large inductor L b , a small resistor R b and a small voltage source V b . Computer simulations of inductance-load-biased Josephson transmission lines (JTLs) show that an SFQ pulse propagates correctly when L b is large enough even if R b is very small. In order to implement the inductance-load-biased JTL, we have made two different layouts: one uses a large bias inductance L b of a typical stripline structure on a ground plane which occupies a rather large area; the other uses L b in the shape of a coplanar stripline, which costs a smaller area.
As single flux quantum (SFQ) circuit complexities scale, larger bias currents are required. The large current produces excessive heat and greatly complicates the design process. Current recycling offers a solution by reducing the required bias current through serially biased circuit blocks. Serial biasing is typically achieved in homogeneous SFQ systems where similar bias currents are required in similar circuits. Each of these homogeneous circuits is often placed on different ground planes and serially biased to reuse the bias currents. To address heterogeneous circuits with varying bias current requirements, a novel serial biasing technique is proposed. An interface between the ground planes with unequal bias current is presented that exhibits a current balancing capability. The interface supplies additional current before passing the current to the next ground plane. The ground planes are arranged in ascending order of bias current to manage the complexity of these heterogeneous circuits. Using a one bit SFQ full adder as an example, the proposed approach demonstrates several key benefits: a 49% reduction in the number of driver-receiver pairs, a 6.5% reduction in power dissipation, and a 35% reduction in bias current across a heterogeneous SFQ circuit placed on three isolated ground planes. The performance, bias current margins, and methods for current reduction are also discussed, showcasing the effectiveness of current recycling in improving the efficiency of complex heterogeneous SFQ systems.
High-frequency input signals from room-temperature microwave sources present a major bottleneck for scaling qubit numbers in universal quantum computers. To address this challenge, we previously developed a superconducting single-flux quantum (SFQ) qubit control circuit (SQCC) capable of generating precise SFQ pulse sequences using only DC bias. This approach eliminates traditional microwave signal chains and enables scalable, low-loss DC-based interconnects. However, as the number of SQCCs increases, the total required bias current grows linearly, leading to significant cable-induced thermal dissipation that limits scalability. In this work, we propose and implement an architecture using recycled bias current to scale up multiple SQCCs (RB-MSQCC). Theoretical analysis indicates that the recycling method can reduce thermal load by a factor of 100 to 1000 compared to conventional biasing. A key enabler of this architecture is a custom-designed driver-receiver pair (DRP) cell, which supports SFQ signal transmission across isolated ground planes using the SIMIT Nb03 process. Based on this, we demonstrate a 4-bit RB-MSQCC prototype. Experimental results confirm stable SFQ pulse generation across all four channels, with output frequencies ranging from 3.42 to 5.27 GHz, consistent with prior results (2.40-8.11 GHz). These findings validate the feasibility and robustness of the proposed scheme under current fabrication constraints. Our study offers both theoretical and experimental support for scalable, energy-efficient SFQ-based qubit control, representing a critical step toward large-scale superconducting quantum processors.
The supply of bias current is one of the key problems to be overcome for fully operational large-scale SFQ circuits. Large currents cause various undesirable effects that degrade circuit operation. The magnetic field induced by a large DC bias current affects the operation of several SFQ cells, even with a microstrip-line structure applied for the bias lines. In this paper, experimental results using SQUIDs show that bias-line shielding is the most effective way to reduce the effect of the DC bias current. The operating margins of SFQ cells were also found to be sensitive to the current in the ground plane. The location of a ground bonding should be close to the point of current injection if we wish to avoid undesirable diffusion of current through the ground plane. We confirmed the effectiveness of bias-line shielding and of the location of ground bonding with a circuit composed of about 500 junctions.