Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Optimization of superconducting microstrip interconnects for rapid single-flux-quantum circuits

M R Rafique, Irina Kataeva, Henrik Engseth, Michael A. Tarasov, Anna Kidiyarova-Shevchenko

Published Jun 20, 2005• 13 citations
Publisher

Abstract

In this paper, issues related to the optimization of superconducting passive interconnects are discussed. Results of the microwave optimization of bends, via connections and crossings of superconducting microstrip lines (SMSLs) are reported. The optimum design of the SMSL cross gives more than 95% of transmission and can be well used in a two-bus cross design with up to 14 signal wires. The results have been confirmed by time-domain simulations and measurements.

DOI
10.1088/0953-2048/18/8/007

Related papers

Interconnect Routing for Large-Scale RSFQ Circuits

Tahereh Jabbari, Gleb Krylov, Stephen R. Whiteley +3 more

The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.

IEEE Transactions on Applied Superconductivity•Mar 4, 2019•88 citations

Design and testing of high-speed interconnects for superconducting multi-chip modules

S Narayana, V K Semenov, Y A Polyakov +2 more

Superconducting single flux quantum (SFQ) circuits can process information at extremely high speeds, in the range of hundreds of GHz. SFQ circuits are based on Josephson junction cells for switching logic and ballistic transmission for transferring SFQ pulses. Multi-chip modules (MCMs) are often used to implement larger complex designs, which cannot be fit onto a single chip. We have optimized the design of wideband interconnects for transferring signals and SFQ pulses between chips in flip-chip MCMs and evaluated the importance of several design parameters such as the geometry of bump pads on chips, length of passive microstrip lines (MSLs) and number of corners in MSLs as well as flux trapping and fabrication effects on the operating margins of the MCMs. Several test circuits have been designed to evaluate the above mentioned features and fabricated in the framework of a 4.5 kA cm −2 HYPRES process. The MCM bumps for electrical connections have been deposited using a wafer-level electroplating process. We have found that, at the optimized configuration, the maximum operating frequency of the MCM test circuit, a ring oscillator with chip-to-chip connections, approaches 100 GHz and is not noticeably affected by the presence of MCM interconnects, decreasing by only about 3% with respect to the same circuit with no inter-chip connections.

arXiv:1206.6120•Superconductor Science and Technology•Aug 30, 2012•31 citations

Flexible Superconducting Passive Interconnects with 50-Gb/s Signal Transmissions in Single-Flux-Quantum Circuits

Takahiro Yamada, Hirofumi Ryoki, Akira Fujimaki +1 more

We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.

Japanese Journal of Applied Physics•Feb 1, 2006•21 citations

A design approach to passive interconnects for single flux quantum logic circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +1 more

We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•53 citations

Design and Investigation of Gate-to-Gate Passive Interconnections for SFQ Logic Circuits

Y. Hashimoto, Shinichi Yorozu, Y. Kameda +3 more

We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.

IEEE Transactions on Applied Superconductivity•Sep 1, 2005•19 citations

Repeater Insertion in SFQ Interconnect

Tahereh Jabbari, Gleb Krylov, Stephen R. Whiteley +2 more

Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.

IEEE Transactions on Applied Superconductivity•Jun 9, 2020•58 citations
In this paper, issues related to the optimization of superconducting passive interconnects are discussed. Results of the microwave optimization of bends, via connections and crossings of superconducting microstrip lines (SMSLs) are reported. The optimum design of the SMSL cross gives more than 95% of transmission and can be well used in a two-bus cross design with up to 14 signal wires. The results have been confirmed by time-domain simulations and measurements.
The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.
Superconducting single flux quantum (SFQ) circuits can process information at extremely high speeds, in the range of hundreds of GHz. SFQ circuits are based on Josephson junction cells for switching logic and ballistic transmission for transferring SFQ pulses. Multi-chip modules (MCMs) are often used to implement larger complex designs, which cannot be fit onto a single chip. We have optimized the design of wideband interconnects for transferring signals and SFQ pulses between chips in flip-chip MCMs and evaluated the importance of several design parameters such as the geometry of bump pads on chips, length of passive microstrip lines (MSLs) and number of corners in MSLs as well as flux trapping and fabrication effects on the operating margins of the MCMs. Several test circuits have been designed to evaluate the above mentioned features and fabricated in the framework of a 4.5 kA cm −2 HYPRES process. The MCM bumps for electrical connections have been deposited using a wafer-level electroplating process. We have found that, at the optimized configuration, the maximum operating frequency of the MCM test circuit, a ring oscillator with chip-to-chip connections, approaches 100 GHz and is not noticeably affected by the presence of MCM interconnects, decreasing by only about 3% with respect to the same circuit with no inter-chip connections.
We have developed a very flexible wiring technique of passive transmission lines (PTLs) in single-flux-quantum (SFQ) circuits. For high flexibility, we introduced two types of wiring structures of strip lines (SLs) and microstrip lines (MSLs) using the fabrication process which has four metal layers. The SLs and MSLs are realized using the second and fourth metal layers as signal lines, respectively, from the bottom (the other two metal layers are used as ground planes). We also introduced via-holes for transmission between the SL and MSL. For solving the problem of impedance mismatch on complicated discontinuous sections such as joints [between the driver(receiver) and the end of SLs(MSLs)] and via-holes, we optimized the structures of these discontinuous sections and evaluated propagation properties to ensure high-speed transmission of SFQ pulses. We tested the transmission of SFQ pulses through SLs/MSLs including more than 50 via-holes, one of the most complicated lines in actual designs. We confirmed the good propagation properties of SFQ pulses up to 50 Gb/s with sufficiently wide bias margins of ±20% to be used in practical designs.
We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.
We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.
Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.