A promising application of a single-flux quantum (SFQ) circuit is read-out circuitry for a multi-channel superconductive sensor array. In such applications, the SFQ read-out circuit is expected to operate outside a magnetic shield. We investigated an SFQ circuit structure, which is tolerant to an external magnetic field, using the AIST 2.5kA/cm2 Nb standard 2 process, which has four Nb wiring layers including the ground plane. By covering the entire circuit using an upper Nb wiring layer called the control (CTL) layer, the influences of the external magnetic field on the SFQ circuit operation can be avoided. We experimentally evaluated the sheet inductance of the wiring layer underneath the CTL shielding layer to design a magnetic-field-tolerant SFQ circuit. We implemented and measured test circuits comprising toggle flip-flops (TFFs) to evaluate their magnetic field tolerances. The operating margin and maximum operating frequency of the designed TFF did not deteriorate with increases in the magnetic field applied to the test circuit, whereas the operating margin of the conventional TFF was reduced by applying the magnetic field. We have also demonstrated the high-speed operation of the designed TFF operated in an unshielded environment at a frequency of up to 120GHz with a wide operating margin.
A promising application of a single-flux quantum (SFQ) circuit is read-out circuitry for a multi-channel superconductive sensor array. In such applications, the SFQ read-out circuit is expected to operate outside a magnetic shield. We investigated an SFQ circuit structure, which is tolerant to an external magnetic field, using the AIST 2.5kA/cm2 Nb standard 2 process, which has four Nb wiring layers including the ground plane. By covering the entire circuit using an upper Nb wiring layer called the control (CTL) layer, the influences of the external magnetic field on the SFQ circuit operation can be avoided. We experimentally evaluated the sheet inductance of the wiring layer underneath the CTL shielding layer to design a magnetic-field-tolerant SFQ circuit. We implemented and measured test circuits comprising toggle flip-flops (TFFs) to evaluate their magnetic field tolerances. The operating margin and maximum operating frequency of the designed TFF did not deteriorate with increases in the magnetic field applied to the test circuit, whereas the operating margin of the conventional TFF was reduced by applying the magnetic field. We have also demonstrated the high-speed operation of the designed TFF operated in an unshielded environment at a frequency of up to 120GHz with a wide operating margin.
An on-chip magnetic shielding technique was characterized on several DC-SQUIDs to prepare the next generation of complex digital RSFQ circuits designed by the FLUXONICS foundry. The maximal frequency of operation of a toggle flip-flop cell was used as a criteria to validate the concept. It goes from a simulated value of 52 GHz (46 ± 2 GHz experimentally), for a McCumber parameter βc= 1 with JC= 1 kA/cm2 in the absence of external magnetic field, down to 29 GHz in the presence of an external field of 88 μT. The shielding technique consists of surrounding a circuit by one or several superconducting niobium loops with the same layers as for the SFQ circuit. The loops are connected to the ground plane with vias. It is shown experimentally that the local magnetic field is reduced by a factor of 4 for the best shielded configuration, which limits the reduction of the maximal frequency of operation in presence of external magnetic field.
We has designed, fabricated, and measured a Single flux quantum (SFQ) toggle flip-flop (TFF). The TFF is widely used in superconductive digital electronics circuits. Many digital devices, such as frequency counter, counting ADC and program counter be used TFF Specially, a program counter may be constructed based on TFF We have designed the newly TFF and obtained high bias margins on test. In this work, we used two circuit simulation tools, WRspice and Julia, as circuit optimization tools. We used XIC for a layout tool. Newly designed TFF had minimum bias margins of +/- and maximum bias margins of +/-(enhanced from +/- ). The designed circuits were fabricated by using Nb technology The test results showed that the re-optimized TFF operated correctly on 100kHz and had a very wide bias margins of +/- .
We report on the functionality of a Nb-based superconducting single flux quantum (SFQ) toggle flip-flop (TFF) circuit, comprising a complementary superconductor–ferromagnet–superconductor (SFS) Josephson π-junction. The SFS junction was used as a phase shifting element inserted in the storage loop of the TFF. The fabricated circuits demonstrated correct functionality with the operation parameter ranges of ± 20%. The application of SFS π-junctions makes the SFQ circuits very compact, may substantially improve their stability, and may also be suitable for integration with Josephson quantum circuits (qubits).
The operating margins of unshielded SFQ circuits are influenced by external magnetic fields, and earlier research showed experimental results of operating region versus bias current for circuits with in-plane and perpendicularly applied magnetic fields. Here, we report a method that can be used to analyze shields to protect SFQ circuits from external magnetic fields. To validate the approach, we investigated a grid-patterned shield of varying spacing. The analysis was done with cell layouts made according to the Hypres' 4.5 kA/cm2process, in which the top-most layer, M3, was used to implement the shields. It was calculated that a grid shield of 2.5 μm grid bar width and spacing of 5 μm offered a good compromise at both providing shielding and causing a relatively small drift in circuit inductance. In order to make SFQ circuits more tolerant to magnetic fields, we have simulated with circuit parameter alterations to realize the best bias and higher operating held margins, due to external magnetic fields. The external magnetic fields are modeled through three orthogonal coils that generate roughly a uniform magnetic held density throughout the cell under test.
ENGLISH ABSTRACT: Single Flux Quantum (SFQ) based electronic circuits are susceptible to failure if exposed to external magnetic fields, even in very small quantities. Operating margins of SFQ circuits have shown to decrease significantly in the presence of magnetic fields as small as 5 μT. This challenge makes SFQ circuits infeasible for the normal environment in which other technologies, such as CMOS, operate. Sources of magnetic fields include SFQ circuit’s own bias lines, the Earth, which can produce magnetic fields up to 65 μT and any other electromagnetic interference sources. Without protective measures, most SFQ circuits cannot work in the open environment. \nBy using the tools available in the inductance extraction tool, InductEx, a method for projecting uniform magnetic fields, of varying orientations on SFQ cells, strides have been made to make SFQ circuits more tolerant to magnetic fields. On-chip analysis of SFQ cells was done in the presence of magnetic fields from the x, y and z orientations. In addition, by varying currents in 3-D coils, the orientation of the magnetic fields can be varied. This way, it is now possible to analyse bias, parameter and operating field margins of SFQ cells in any direction of the magnetic field. \nTwo on-chip shielding solutions were analysed and developed. The conventional continuous superconductor \nlayer shield, dubbed the solid shield, and the grid shield. The grid shield resembles a Faraday \ncage and it is implemented by laying out bars of 2.5 μm width using the topmost layer in the Hypres0 \n4.5 kA/cm2 process. The solid shield is more effective against perpendicular (z-directed) magnetic fields \nthan against those in-plain (x and y-directed). In addition, the solid shield’s inclusion in SFQ cells results \nin the reduction of circuit inductance by up to 25 %. The grid shield is a very effective approach against \nin-plane magnetic fields. However, its effectiveness is inversely proportional to the spacing between grid \nbars. Compared to the solid shield, the grid shield has less effect on circuit inductance with a typical \nreduction of 8 % at a grid bar spacing of 5 μm. The large reduction in inductance can be overcome \nby making the inductors thinner and shorter. Shielding effectiveness of on-chip shields is enhanced by \nmaking ground contact vias from the shield layer to the ground plane. So far, uniformly grounded shields \nhave shown to be the most effective approach. \nThe solid shield improved the operating field margin of a DFF cell against a z-directed magnetic field \nfrom 30 μT to 531 μT, while the grid shield, of 5 μm grid spacing, improved the margins from 68 μT \nto 290 μT against an x-directed magnetic field. In the DC-SFQ cell, the operating field margin was \nimproved with a solid shield from 47 μT to 464 μT, against a z-directed magnetic field, while with a \ngrid shield, the improvement was from 211 μT to 381 μT, against an x-directed fields. \nTo further enhance the magnetic field tolerance of SFQ circuits, design tenets that target specific components, \nsuch as inductors, were analysed. Thin and narrow inductors have shown less coupling to \nexternal magnetic fields. In addition, moats have shown to influence OFM results depending on the \norientation of magnetic fields. \nThis work has delivered design and analysis methods for magnetic field tolerant SFQ circuits.
The authors report the design, fabrication, and test results of single flux quantum (SFQ) toggle flip flop circuits. These circuits, investigated as building blocks of an HTS counting ADC, feature a directly coupled readout junction stack similar to those used in LTS RSFQ circuits. The directly coupled circuit delivers higher readout voltage, hence potentially higher operating speed than magnetically coupled alternatives. The circuits were fabricated using two multilayer HTS SNS junction integrated circuit technologies (one at Northrop Grumman and the other at TRW) featuring three YBCO depositions. Initial testing demonstrated toggling of a T-flip flop in response to SFQ pulses generated by integrated dc/SFQ converters. The readout voltage is shown to approach 40% of the junction I/sub C/R/sub N/ product, and as high as 100 /spl mu/V at 65K. Test results are compared with predicted fabrication process parameter requirements. To increase margins and tolerance to process parameter variations, improvements to the design have been made using JSpice and MALT.