Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Cryogenic direct current superconducting quantum interference device readout circuit

Michael Mück, Matthias Korn, Chas Mugford, Jan B. Kycia

Published Jun 27, 2005• 4 citations
Publisher

Abstract

We have designed and tested a superconducting quantum interference device (SQUID) readout circuit, which can be operated at liquid helium temperatures. Although room-temperature SQUID electronics perform well, it is sometimes desirable to keep the wires between SQUID, readout electronics, and feedback coil as short as possible to minimize phase shifts and time delays. Cooling the readout circuit to low temperatures can also decrease its thermal noise. Our readout circuit uses conventional ac-flux modulation, which significantly reduces low frequency excess noise and drift in the preamplifier. In this case, simple complementary metal–oxide–semiconductor circuits with low power dissipation can be used as amplifier, phase-sensitive detector and integrator. The power dissipation of the complete readout is less than 15mW at 5V supply voltage.

DOI
10.1063/1.1947880

Related papers

High-TC rf superconducting quantum interference device readout with a cryogenic preamplifier

Dongfeng He, M. Tachiki, Hideo Itozaki

A high-TC rf superconducting quantum interference device (SQUID) readout with a cryogenic preamplifier was developed. The noise figure of the preamplifier at 350MHz was about 0.92dB at room temperature and 0.35dB at 77K. For a high-TC yttrium barium copper oxide rf SQUID coupled with a lumped element tank circuit with a resonant frequency of about 360MHz, the white flux noise was about 25μΦ0∕√Hz and 22μΦ0∕√Hz when the preamplifier was at room temperature and at 77K, respectively. The flux noise was only reduced by about 12% using the cryogenic preamplifier. As the thermal noise of the SQUID and the noise generated by the tank circuit are already higher than the preamplifier noise, cooling the preamplifier has only a small effect of the system noise, when the SQUID is operated at 77K. Lower operating temperatures, e.g., when using a SQUID made from MgB2, might justify the use of a cooled preamplifier.

Review of Scientific Instruments•Jun 1, 2006•0 citations

Improved dc SQUID read-out electronics with low 1/f noise preamplifier

D. Drung

An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.

Review of Scientific Instruments•Nov 1, 1997•43 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•76 citations

Investigation and optimization of low-frequency noise performance in readout electronics of dc superconducting quantum interference device

Jing Bo Zhao, Yi Zhang, Yong-Ho Lee +1 more

We investigated and optimized the low-frequency noise characteristics of a preamplifier used for readout of direct current superconducting quantum interference devices (SQUIDs). When the SQUID output was detected directly using a room-temperature low-voltage-noise preamplifier, the low-frequency noise of a SQUID system was found to be dominated by the input current noise of the preamplifiers in case of a large dynamic resistance of the SQUID. To reduce the current noise of the preamplifier in the low-frequency range, we investigated the dependence of total preamplifier noise on the collector current and source resistance. When the collector current was decreased from 8.4 mA to 3 mA in the preamplifier made of 3 parallel SSM2220 transistor pairs, the low-frequency total voltage noise of the preamplifier (at 0.1 Hz) decreased by about 3 times for a source resistance of 30 Ω whereas the white noise level remained nearly unchanged. Since the relative contribution of preamplifier's input voltage and current noise is different depending on the dynamic resistance or flux-to-voltage transfer of the SQUID, the results showed that the total noise of a SQUID system at low-frequency range can be improved significantly by optimizing the preamplifier circuit parameters, mainly the collector current in case of low-noise bipolar transistor pairs.

Review of Scientific Instruments•May 1, 2014•19 citations

Investigation of silicon field-effect transistors in cryogenic amplifiers for radio frequency superconducting quantum interference devices

T. Becker, Michael Mück, Christoph Heiden

We have prepared n-channel silicon field-effect transistors, which are capable of working at liquid helium temperatures (4.2 K) and used them in cooled preamplifiers for rf superconducting quantum interference device (SQUID) readout electronics. All metallizations of these transistors were made of niobium, to study the possibility of a further integration of a SQUID and FET on the same chip. Using the FETs in a cooled preamplifier together with a rf SQUID gradiometer, the flux noise of the system could be reduced by a factor of 3 compared to a room temperature low noise preamplifier. We have also performed calculations of a possible increase of the substrate temperature due to the power dissipation of the FET and have measured the cross talk between FET and SQUID.

Review of Scientific Instruments•May 1, 1995•0 citations

Use of super Schottky diodes in a cryogenic radio frequency superconducting quantum interference device readout

Michael Mück, Th. Becker, Christoph Heiden

We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.

Applied Physics Letters•Jan 16, 1995•2 citations
We have designed and tested a superconducting quantum interference device (SQUID) readout circuit, which can be operated at liquid helium temperatures. Although room-temperature SQUID electronics perform well, it is sometimes desirable to keep the wires between SQUID, readout electronics, and feedback coil as short as possible to minimize phase shifts and time delays. Cooling the readout circuit to low temperatures can also decrease its thermal noise. Our readout circuit uses conventional ac-flux modulation, which significantly reduces low frequency excess noise and drift in the preamplifier. In this case, simple complementary metal–oxide–semiconductor circuits with low power dissipation can be used as amplifier, phase-sensitive detector and integrator. The power dissipation of the complete readout is less than 15mW at 5V supply voltage.
A high-TC rf superconducting quantum interference device (SQUID) readout with a cryogenic preamplifier was developed. The noise figure of the preamplifier at 350MHz was about 0.92dB at room temperature and 0.35dB at 77K. For a high-TC yttrium barium copper oxide rf SQUID coupled with a lumped element tank circuit with a resonant frequency of about 360MHz, the white flux noise was about 25μΦ0∕√Hz and 22μΦ0∕√Hz when the preamplifier was at room temperature and at 77K, respectively. The flux noise was only reduced by about 12% using the cryogenic preamplifier. As the thermal noise of the SQUID and the noise generated by the tank circuit are already higher than the preamplifier noise, cooling the preamplifier has only a small effect of the system noise, when the SQUID is operated at 77K. Lower operating temperatures, e.g., when using a SQUID made from MgB2, might justify the use of a cooled preamplifier.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
We investigated and optimized the low-frequency noise characteristics of a preamplifier used for readout of direct current superconducting quantum interference devices (SQUIDs). When the SQUID output was detected directly using a room-temperature low-voltage-noise preamplifier, the low-frequency noise of a SQUID system was found to be dominated by the input current noise of the preamplifiers in case of a large dynamic resistance of the SQUID. To reduce the current noise of the preamplifier in the low-frequency range, we investigated the dependence of total preamplifier noise on the collector current and source resistance. When the collector current was decreased from 8.4 mA to 3 mA in the preamplifier made of 3 parallel SSM2220 transistor pairs, the low-frequency total voltage noise of the preamplifier (at 0.1 Hz) decreased by about 3 times for a source resistance of 30 Ω whereas the white noise level remained nearly unchanged. Since the relative contribution of preamplifier's input voltage and current noise is different depending on the dynamic resistance or flux-to-voltage transfer of the SQUID, the results showed that the total noise of a SQUID system at low-frequency range can be improved significantly by optimizing the preamplifier circuit parameters, mainly the collector current in case of low-noise bipolar transistor pairs.
We have prepared n-channel silicon field-effect transistors, which are capable of working at liquid helium temperatures (4.2 K) and used them in cooled preamplifiers for rf superconducting quantum interference device (SQUID) readout electronics. All metallizations of these transistors were made of niobium, to study the possibility of a further integration of a SQUID and FET on the same chip. Using the FETs in a cooled preamplifier together with a rf SQUID gradiometer, the flux noise of the system could be reduced by a factor of 3 compared to a room temperature low noise preamplifier. We have also performed calculations of a possible increase of the substrate temperature due to the power dissipation of the FET and have measured the cross talk between FET and SQUID.
We describe the fabrication and characterization of super Schottky diodes which are used in the cryogenic part of a 3 GHz radio frequency superconducting quantum interference device (rf SQUID) readout electronics. The diodes were prepared on silicon wafers with an n-doping level of 5×1024 m−3. They exhibited sensitivities of 1500 V−1 at 4.2 K, and a noise equivalent power of 2×10−15 W/√Hz was measured at 2.1 GHz. Using planar niobium 3 GHz rf SQUIDs and a cooled rf amplifier, experiments have been performed to investigate the feasibility of these super Schottky diodes for demodulation of the SQUID rf signal voltage. A simple cryogenic rf SQUID readout, employing two transistors and one super Schottky diode is described and investigated. Flux noise measurements in an open loop have been performed using this readout.