Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Communications Magazine

Superconductor digital RF development for software radio

DARREN K. BROCK, Oleg A. Mukhanov, José M. de la Rosa

Published Jan 1, 2001• 44 citations
Publisher

Abstract

We review a new "direct digitization" approach for "digital RF" architectures for software radio. Although direct digitization usually implies the simultaneous digitization of all channels in a particular band at a downconverted IF, we use this term to refer exclusively to the direct digitization of all bands, from near DC to RF. Furthermore, we present results on band selection and digitization of RF signals directly at the carrier frequency with high resolution. These novel approaches are enabled by a superconductor analog-to-digital converter technology using an ultra-fast IC logic known as Rapid Single Flux Quantum (RSFQ) logic, with performance capable of enabling envisioned software radios.

DOI
10.1109/35.900649

Related papers

Superconductor Microelectronics: A Digital RF Technology for Software Radios

DARREN K. BROCK

This chapter contains sections titled: Introduction Superconductivity and the Josephson Effect Established Applications of Superconductors Emerging Applications - Software Defined Radio Rapid Single Flux Quantum Digital Logic Circuit Characteristics Example RSFQ Logic Gate - RS Flip Flop RSFQ Data Converters RSFQ Scaling theory Cryogenic Aspects Superconductor SDR for Commercial Applications Superconductors in Wireless Communications Advantages of Superconductor Receivers Trends in Spread Spectrum Communications High Power Amplifier Linearization Digital RF Transceiver Superconductor SDR for Military Applications Co-Site Interference Digitally Dehopping Spread Spectrum Signals Satellite Communications Accommodating New Waveforms Massive Time Multiplexing Conclusions Acknowledgements References

Wiley eBooks•May 15, 2002•2 citations

Superconductor Digital-RF Receiver Systems

Oleg A. Mukhanov, Dmitri E. Kirichenko, I. V. Vernik +12 more

Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ∼30GHz clock frequencies.

IEICE Transactions on Electronics•Mar 1, 2008•129 citations

High Performance HF-VHF All Digital RF Receiver Tested at 20 GHz Clock Frequencies

Anna De Escobar, Richard Hitt, Oleg A. Mukhanov +1 more

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz

IEEE Military Communications Conference (MILCOM)•Oct 1, 2006•7 citations

Superconductor analog-to-digital converters

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +1 more

Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.

Proceedings of the IEEE•Sep 20, 2004•182 citations

Superconductor Digital-RF Transceiver Components

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +3 more

Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.

•Jan 1, 2006•7 citations

The Testing of Superconductive ADCs in a Software-Defined Radio Base Stations

Abhishek Arun, Hans G. Kerkhoff, Marcel H.H. Weusthof

Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external

•Nov 29, 2001•1 citation
We review a new "direct digitization" approach for "digital RF" architectures for software radio. Although direct digitization usually implies the simultaneous digitization of all channels in a particular band at a downconverted IF, we use this term to refer exclusively to the direct digitization of all bands, from near DC to RF. Furthermore, we present results on band selection and digitization of RF signals directly at the carrier frequency with high resolution. These novel approaches are enabled by a superconductor analog-to-digital converter technology using an ultra-fast IC logic known as Rapid Single Flux Quantum (RSFQ) logic, with performance capable of enabling envisioned software radios.
This chapter contains sections titled: Introduction Superconductivity and the Josephson Effect Established Applications of Superconductors Emerging Applications - Software Defined Radio Rapid Single Flux Quantum Digital Logic Circuit Characteristics Example RSFQ Logic Gate - RS Flip Flop RSFQ Data Converters RSFQ Scaling theory Cryogenic Aspects Superconductor SDR for Commercial Applications Superconductors in Wireless Communications Advantages of Superconductor Receivers Trends in Spread Spectrum Communications High Power Amplifier Linearization Digital RF Transceiver Superconductor SDR for Military Applications Co-Site Interference Digitally Dehopping Spread Spectrum Signals Satellite Communications Accommodating New Waveforms Massive Time Multiplexing Conclusions Acknowledgements References
Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ∼30GHz clock frequencies.
Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz
Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.
Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.
Software-Defined Radio (SDR), as explained in [1], is a promising concept for the wireless communication industry since the entire transceiver function can be implemented in software, avoiding the replacement of hardware each time the system has to be upgraded. However, the practical implementation of such a system is depended on the hardware, which consists of precise, ultra highspeed electronic devices such as Analog-to-Digital Converters (ADCs). The present state-of-the-art semiconductor ADCs cannot be used for the implementation of SDR in the near future [2]. Some of the factors that hamper the implementation are the requirements of very high speed of a few tens of GHz and the high resolution (e.g. 16 bits) at these speeds. On the other hand, using the Low-Temperature Superconducting (LTS) technology [3], which relays on the quantum mechanical property of superconductors, very high-speed electronic devices with the accuracy of a flux quantum, can be constructed. In a closed superconducting loop, the magnetic flux can exist only in discrete quantized amounts equal to the multiples of the magnetic flux quantum, φ0 = h/2e ~ 2.07x10 Wb. The theoretical speed limit of such a Rapid Single Flux Quantum (RSFQ) device is close to 1 THz [4]. These RSFQ circuits are the fastest of all devices built in any known technology. The basic building block of an RSFQ circuit is the Josephson Junction (JJ), which is formed when two superconductors are separated by an interface. Since RSFQ circuits work at extremely high speeds, testing and verification of such a device is a difficult and challenging task. Direct testing at these speeds is not possible at this moment. Furthermore, the costs of the equipment required for such tests would be extremely high. Hence methods have to be developed to reduce the requirements of external