Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Low Temperature Physics

Design and fabrication of thin-film resistive SQUIDs

G.S. Krivoy, C. A�mann, M. Peters, H. Koch

Published Apr 1, 1995• 9 citations
Publisher
DOI
10.1007/bf00753623

Related papers

The fabrication and characterization of nano-SQUIDs based on Nb thin films

Xixi Liu, Xiaoyu Liu, Hao Wang +2 more

Physica C Superconductivity•May 18, 2015•8 citations

The design, construction and operation of practical thin film superconducting quantum interference devices (SQUIDs)

David Hutson

•Jan 1, 1987•0 citations

An all thin film resistive dc SQUID

S. Menkel, C. Aßmann, G.S. Krivoy +1 more

Czechoslovak Journal of Physics•May 1, 1996•4 citations

An all thin-film resistive DC SQUID-a current-controlled oscillator

G.S. Krivoy, H. Koch

An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.

Superconductor Science and Technology•Oct 1, 1992•14 citations

Nb-Oxide-Pb Tunnel Junctions Fabricated Using CF4 Cleaning Process. (III) Preparation of Planar dc SQUID

Yujiro Katoh, H. Asano, K. Tanabe +1 more

This paper discusses the preparation of thin-film planar dc superconducting quantum interference devices (SQUIDs). Nb-oxide-Pb tunnel junctions fabricated using CF4 cleaning process (CFCP) and Pd thin-film shunt resistor were employed. It was demonstrated that the two junctions in a SQUID have symmetrical and wellcontrolled junction parameters. Pd adhesion with oxidized Si could be improved by ultrathin Zr underlayers. The Pd films allowed good controt of the sheet resistance. The SQUIDs are very reliable in regard to room-temperature storage and thermal cycling.

Japanese Journal of Applied Physics•Oct 1, 1987•2 citations

Investigation of the design of a digital SQUID sensor

Friedrich Uhlmann, St Lange, M. Khabipov +1 more

Physica C Superconductivity•Nov 1, 1999•7 citations
An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.
This paper discusses the preparation of thin-film planar dc superconducting quantum interference devices (SQUIDs). Nb-oxide-Pb tunnel junctions fabricated using CF4 cleaning process (CFCP) and Pd thin-film shunt resistor were employed. It was demonstrated that the two junctions in a SQUID have symmetrical and wellcontrolled junction parameters. Pd adhesion with oxidized Si could be improved by ultrathin Zr underlayers. The Pd films allowed good controt of the sheet resistance. The SQUIDs are very reliable in regard to room-temperature storage and thermal cycling.