Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

An all thin-film resistive DC SQUID-a current-controlled oscillator

G.S. Krivoy, H. Koch

Published Oct 1, 1992• 14 citations
Publisher

Abstract

An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.

DOI
10.1088/0953-2048/5/10/009

Related papers

Thin-film resistive SQUIDS

G.S. Krivoy, H. Koch

Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•4 citations

Tunable narrow-linewidth oscillations and current-voltage characteristics of a resistive dc SQUID

J. M. V. Verschueren, A. A. Uiterwaal, Rob W. van der Heijden +1 more

The output voltage of a dc superconducting quantum interference device (SQUID) containing a resistive section Rs oscillates at a frequency νq =Vs/ φ0 (φ0=flux quantum) when a current controlled voltage Vs is maintained across Rs. These oscillations have been observed from ∼10−1 to 1011 Hz, using Rs values ranging from ∼10−10 to ∼10−3 Ω in low inductance (∼10−10 H) point contact SQUID loops. At high frequencies, they manifest themselves in the dc current-voltage characteristics by inducing extra current steps.

Applied Physics Letters•Jul 15, 1983•12 citations

All-Nb low-noise dc SQUID with 1-μm tunnel junctions

Richard F. Voss, Robert B. Laibowitz, Stanley I. Raider +1 more

Tunnel-junction dc SQUIDs are being fabricated from Nb films using electron-beam lithography to define linewidths as small as 0.5 μm. The barriers in the Nb-NbOx-Nb junctions are grown in an oxygen plasma discharge, and the Pd2Si resistive shunts are formed by annealing Pd on the Si substrates. These devices have excellent storage and recycling properties. At a measurement frequency of 40 kHz, a SQUID with an inductance of about 1 nH, a critical current of about 4 μA, and a parallel shunt resistance of about 15 Ω had an intrinsic energy resolution of 2.5×10−32 J Hz−1 at 4.2 K and 1.1×10−32 J Hz−1 at 1.6 K, in good agreement with a model of the dc SQUID.

Journal of Applied Physics•Apr 1, 1980•30 citations

Tunable HTS rf Josephson-effect oscillator based on YBCO-Au-YBCO resistive SQUID

L Hao, D.A. Peden, John C. Gallop +1 more

We report the successful realization of a resistively shunted two-junction high temperature superconducting (HTS) SQUID in which the heterodyne signal generated between the two YBCO grain-boundary junctions is accurately controlled in the range of 1–50 MHz by adjustment of the bias current in the milliampere range through a thin-film on-chip YBCO-Au-YBCO shunt resistor (∼25 μΩ). Oscillations in the temperature range 20–60 K and signal powers up to 2 nW in a 20 kHz bandwidth have been recorded.

Superconductor Science and Technology•Nov 21, 2001•5 citations

A broadband picovoltmeter based on the direct current superconducting quantum interference device with additional positive feedback

Vladimir Polushkin, D. Drung, H. Koch

A picovoltmeter working at 4.2 K and based on a direct current superconducting quantum interference device (dc SQUID) with additional passive positive feedback for investigating the properties of superconducting thin films, Josephson junctions, and SQUIDs has been developed. It has a large small-signal bandwidth fm≂800 kHz, a slew rate of ≂38 mV/s, a dynamic range of 146 dB, and a voltage resolution of 5 pV/Hz1/2 for a signal source impedance Rs=0 Ω. The noise temperature is ≂0.6 K for Rs=1 Ω. In this article the dynamics and noise properties of the instrument are discussed.

Review of Scientific Instruments•Sep 1, 1994•18 citations

Low noise DC SQUIDs fabricated in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology

M. B. Ketchen, Manjul Bhushan, Steven B. Kaplan +1 more

The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations
An all thin-film resistive SQUID with two Josephson tunnel junctions has been designed, fabricated and studied. As well as the two junctions, this device consists of a low ohmic (1.9*10 -6 Omega ) resistive part connected by superconducting leads to both junctions in a loop with very low ( approximately 10 -11 H) inductance. A direct current flowing through the resistive part fixes the voltage difference between the two Josephson junctions that are additionally fed by a bias current. The voltage difference is converted into a signal frequency that can be picked up from the SQUID with a conversion factor of ( phi o ) -1 =483.6 MHz mu V -1 , defined only by the electron charge and Planck's constant. An output signal level (peak-to-peak) of about 50 mu V has been obtained. The low frequency range (below 100 kHz) of the output signal frequency has been investigated. The possibilities of considerably extending this frequency range are also discussed.
Different all thin-film partly resistive superconducting quantum interference devices (RSQUIDs) for noise thermometry in the liquid helium temperature range were designed and investigated. Three different types of RSQUID were realised: (i) dc RSQUID, (ii) rf RSQUID, and (iii) RSQUID with two quantization loops (double RSQUID). Shunted tunnel junctions were used as weak links. The resistive parts have been made as a Cu thin film combined with Nb thin films either as a sandwich or a planar element. The devices using a rf pump have integrated rf coupling coils. Resistances of the resistive parts in the range from 2.69 /spl mu//spl Omega/ to 246 /spl mu//spl Omega/ were obtained. The output signal was /spl ap/50 /spl mu/V for the dc RSQUIDs, up to 80 /spl mu/V for the rf RSQUIDs, and up to 1.2 mV for the double RSQUIDs. The linear dependences of the output signal frequency versus a dc current passed through the resistive part were observed up to 40 MHz. The double RSQUIDS described have a clear advantage in the output signal compared to the other RSQUIDs.>
The output voltage of a dc superconducting quantum interference device (SQUID) containing a resistive section Rs oscillates at a frequency νq =Vs/ φ0 (φ0=flux quantum) when a current controlled voltage Vs is maintained across Rs. These oscillations have been observed from ∼10−1 to 1011 Hz, using Rs values ranging from ∼10−10 to ∼10−3 Ω in low inductance (∼10−10 H) point contact SQUID loops. At high frequencies, they manifest themselves in the dc current-voltage characteristics by inducing extra current steps.
Tunnel-junction dc SQUIDs are being fabricated from Nb films using electron-beam lithography to define linewidths as small as 0.5 μm. The barriers in the Nb-NbOx-Nb junctions are grown in an oxygen plasma discharge, and the Pd2Si resistive shunts are formed by annealing Pd on the Si substrates. These devices have excellent storage and recycling properties. At a measurement frequency of 40 kHz, a SQUID with an inductance of about 1 nH, a critical current of about 4 μA, and a parallel shunt resistance of about 15 Ω had an intrinsic energy resolution of 2.5×10−32 J Hz−1 at 4.2 K and 1.1×10−32 J Hz−1 at 1.6 K, in good agreement with a model of the dc SQUID.
We report the successful realization of a resistively shunted two-junction high temperature superconducting (HTS) SQUID in which the heterodyne signal generated between the two YBCO grain-boundary junctions is accurately controlled in the range of 1–50 MHz by adjustment of the bias current in the milliampere range through a thin-film on-chip YBCO-Au-YBCO shunt resistor (∼25 μΩ). Oscillations in the temperature range 20–60 K and signal powers up to 2 nW in a 20 kHz bandwidth have been recorded.
A picovoltmeter working at 4.2 K and based on a direct current superconducting quantum interference device (dc SQUID) with additional passive positive feedback for investigating the properties of superconducting thin films, Josephson junctions, and SQUIDs has been developed. It has a large small-signal bandwidth fm≂800 kHz, a slew rate of ≂38 mV/s, a dynamic range of 146 dB, and a voltage resolution of 5 pV/Hz1/2 for a signal source impedance Rs=0 Ω. The noise temperature is ≂0.6 K for Rs=1 Ω. In this article the dynamics and noise properties of the instrument are discussed.
The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.