Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

IF impedance and mixer gain of NbN hot electron bolometers

J. Kooi, J. J. A. Baselmans, Merlijn Hajenius, J. R. Gao, T. M. Klapwijk, Pieter Dieleman, Andrey M. Baryshev, Gert J. de Lange

Published Feb 15, 2007• 36 citations
Publisher

Abstract

The intermediate frequency (IF) characteristics, the frequency dependent IF impedance, and the mixer conversion gain of a small area hot electron bolometer (HEB) have been measured and modeled. The device used is a twin slot antenna coupled NbN HEB mixer with a bridge area of 1×0.15μm2, and a critical temperature of 8.3K. In the experiment the local oscillator frequency was 1.300THz, and the (IF) 0.05–10GHz. We find that the measured data can be described in a self-consistent manner with a thin film model presented by Nebosis et al. [Proceedings of the Seventh International Symposium on Space Terahertz Technology, Charlottesville, VA, 1996 (unpublished), pp. 601–613], that is based on the two temperature electron-phonon heat balance equations of Perrin-Vanneste [J. Phys. (Paris) 48, 1311 (1987)]. From these results the thermal time constant, governing the gain bandwidth of HEB mixers, is observed to be a function of the electron-phonon scattering time, phonon escape time, and the electron temperature. From the developed theory the maximum predicted gain bandwidth for a NbN HEB is found to be 5.5–6GHz. In contrast, the gain bandwidth of the device under discussion was measured to be ∼2.3GHz which, consistent with the outlined theory, is attributed to a somewhat low critical temperature and nonoptimal film thickness (6nm).

DOI
10.1063/1.2400086

Related papers

IF Impedance and Mixer Gain of Hot-Electron Bolometers and the Perrin-Varmeste Two Temperature Model

J. Kooi, J. J. A. Baselrnans, J. R. Gao +5 more

We have measured the frequency dependent IF impedance and mixer conversion gain of a small area NbN hot electron bolometer (HEB). The device used is a twin slot antenna coupled NbN HEB mixer with a bridge area of 1 x 0.15 mm, and a critical temperature of 8.3K. In the experiment the local oscillator (LO) frequency was 1.300 THz, and the intermediate frequency (IF) 0.05-10 GHz. We find that the measured data can be described in a self consistent manner with a thin film model presented by Nebosis, Semenov, Gousev, and Renk, that is based on the two temperature electron-phonon heat balance equations of Perrin-Vanneste. From these results the thermal time constant, governing the gain bandwidth of HEB mixers, is observed to not only be a function of the electron-phonon scattering time and phonon escape time, but also a function of electron temperature. The latter is due to the temperature dependence of the electron and phonon specific heat. Because hot electron bolometers nominally operate at, or slightly above, the critical temperature (TO of the superconducting film, where local resistivity as a function of electron temperature is largest, it follows that the critical temperature of the film plays an important role in determining the FMB mixer gain bandwidth. For an NbN based hot electron bolometer, the maximum predicted gain bandwidth is approximately 5.5 GHz, given a film thickness of 3.5 nm and a Tc=12K.

•Jan 1, 2006•0 citations

IF Impedance and Mixer Gain of Phonon Cooled Hot-Electron Bolometers and the Perrin-Vanneste Two Temperature Model

J. Kooi, J. J. A. Baselmans, J. R. Gao +6 more

We have measured the IF impedance and mixer gain bandwidth of a small area phonon cooled hot-electron bolometer in the 0.05-10 GHz range under a variety of bias and LO pumping level conditions. The device used is a twin slot antenna coupled NbN HEB mixer, with a bridge area of 1 μm x 0.15 μm, and a critical temperature of 8.3 K. We model the HEB IF impedance following the work of Nebosis, Semenov, Gousev, and Renk, from now on refered to as the ”NSGR” model. This model is based on the two-temperature model of Perrin-Vanneste, and is found to accurately describe the measured data at different bias and LO pump levels. Three fitting parameters are used in the NSGR model to describe the frequency dependent modulation of the electron temperature; the electron-phonon interaction time τeph, the phonon escape time (into the substrate) τes, and the ratio of the electron and phonon specific heat capacity ce/cph. The described time constants and temperature dependent heat capacity ratio obtained from fitting the model to the measured data agrees well with those reported on for thin NbN films in literature. Using an expression for mixer gain from the NSGR model, but modified to take additional parasitic loss and the complex voltage reflection between mixer and IF load impedance into account, we find when we use the impedance fit parameters τeph, τes, ce/cph, an excellent agreement between measured and modeled HEB conversion gain. Keywords— IF Impedance, phonon cooled hot electron bolometer (pHEB), two-temperature model, ”hot” electrons, Perrin-Vanneste, NSGR model, electron temperature modulation, electron-phonon interaction time, phonon escape time, electro-thermal feedback, complex impedance, HEB mixer conversion gain.

•Jan 1, 2005•3 citations

Large Bandwidth of NbN Phonon-Cooled Hot-Electron Bolometer Mixers

Serguei Cherednichenko, Pavel A. Yagoubov, K. Ilin +2 more

The bandwidth of NbN phonon-cooled hot electron bolometer mixers has been systematically investigated with respect to the film thickness and film quality variation. The films, 2.5 to 10 nm thick, were fabricated on sapphire substrates using DC reactive magnetron sputtering. All devices consisted of several parallel strips, each 1 μ wide and 2 μ long, placed between Ti-Au contact pads. To measure the gain bandwidth we used two identical BWOs operating in the 120-140 GHz frequency range, one functioning as a local oscillator and the other as a signal source. The majority of the measurements were made at an ambient temperature of 4.2 K with optimal LO and DC bias. The maximum 3 dB bandwidth (about 4 GHz) was achieved for the devices made of films which were 2.5-3.5 nm thick, had a high critical temperature, and high critical current density. A theoretical analysis of bandwidth for these mixers based on the two-temperature model gives a good description of the experimental results if one assumes that the electron temperature is equal to the critical temperature.

European Microwave Conference (EuMC)•Sep 1, 1997•27 citations

Comparative Study of the Bandwidth of Phonon-Cooled NbN Hot-Electron Bolometers in Submillimeter and Optical Wavelength Ranges

K. Ilin, Serguei Cherednichenko, Gregory N Gol'tsman +2 more

We report the results of the bandwidth measurements of NbN hot-electron bolometers, perfomied in the terahertz frequency domain at 140 GHz and 660 GHz and in time domain in the optical range at the wavelength of 395 nm.. Our studies were done on 3.5-nm-thick NbN films evaporated on sapphire substrates and patterned into ilin-size microbridges. In order to measure the gain bandwidth, we used two identical BWOs (140 or 660 GHz), one functioning as a local oscillator and the other as a signal source. The bandwidth we achieved was 3.5-4 GHz at 4.2 K with the optimal LO and DC biases. Time-domain measurements with a resolution below 300 fs were performed using an electro-optic sampling system, in the temperature range between 4.2 K to 9 K at various values of the bias current and optical power. The obtained response time of the NbN hot-electron bolometer to —100fs-wide Ti:sapphire laser pulses was about 27 ps, what corresponds to the 5.9 GHz gain bandwidth. Introduction The bandwidth of hot-electron bolometer (HEB) mixers has reached values which are record for bolometers. The gain bandwidth for phonon-cooled NbN HEB mixers of 4 GHz for 140 GHz and 650 GHz frequencies [1, 2] and the noise bandwidth of 8 GHz for 650 GHz [2] have been demonstrated. For diffusion-cooled Nb HEB mixers, the bandwidth has reached 6 GHz, when measured at 20--40 GHz [3]. However, there is a definite practical interest to even further extend the bandwidth of these devices. The possibilities of the HEB mixer technology in this direction are far from being exhausted. For example, the future of the NbN HEB technology requires that critical temperature Tc > 10 K and critical current density j c > 10 6 Akm at 4.2 K are simultaneously obtained for d < 3 nm-thick films M. The reduction of the optimal power of the local oscillator PLID below 100 nW leads to the decrease of the device length down to L < 0.2 pm, which, in turn, should bring an additional cooling channel for hot electrons—diffusion into metal contacts and a further bandwidth extension.

Softwaretechnik-Trends•Mar 1, 1998•0 citations

Heterodyne measurements of a NbN superconducting hot electron mixer at terahertz frequencies

Pavel A. Yagoubov, M. Kroug, H. Merkel +6 more

The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•6 citations

Performance of NbN phonon-cooled hot-electron bolometric mixer at Terahertz frequencies

Pavel A. Yagoubov, M. Kroug, H. Merkel +6 more

The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The results of the DSB noire temperature are: 1300 K at 650 GHz, 4700 K at 2.5 TBz and 10000 K at 3.12 THz. The RF bandwidth of the receiver is at least 2.5 THz. The amount of LO power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain is measured to be -9 dB, the total conversion gain -14 dB.

IEEE International Conference on Terahertz Electronics (THz)•Nov 27, 2002•1 citation
The intermediate frequency (IF) characteristics, the frequency dependent IF impedance, and the mixer conversion gain of a small area hot electron bolometer (HEB) have been measured and modeled. The device used is a twin slot antenna coupled NbN HEB mixer with a bridge area of 1×0.15μm2, and a critical temperature of 8.3K. In the experiment the local oscillator frequency was 1.300THz, and the (IF) 0.05–10GHz. We find that the measured data can be described in a self-consistent manner with a thin film model presented by Nebosis et al. [Proceedings of the Seventh International Symposium on Space Terahertz Technology, Charlottesville, VA, 1996 (unpublished), pp. 601–613], that is based on the two temperature electron-phonon heat balance equations of Perrin-Vanneste [J. Phys. (Paris) 48, 1311 (1987)]. From these results the thermal time constant, governing the gain bandwidth of HEB mixers, is observed to be a function of the electron-phonon scattering time, phonon escape time, and the electron temperature. From the developed theory the maximum predicted gain bandwidth for a NbN HEB is found to be 5.5–6GHz. In contrast, the gain bandwidth of the device under discussion was measured to be ∼2.3GHz which, consistent with the outlined theory, is attributed to a somewhat low critical temperature and nonoptimal film thickness (6nm).
We have measured the frequency dependent IF impedance and mixer conversion gain of a small area NbN hot electron bolometer (HEB). The device used is a twin slot antenna coupled NbN HEB mixer with a bridge area of 1 x 0.15 mm, and a critical temperature of 8.3K. In the experiment the local oscillator (LO) frequency was 1.300 THz, and the intermediate frequency (IF) 0.05-10 GHz. We find that the measured data can be described in a self consistent manner with a thin film model presented by Nebosis, Semenov, Gousev, and Renk, that is based on the two temperature electron-phonon heat balance equations of Perrin-Vanneste. From these results the thermal time constant, governing the gain bandwidth of HEB mixers, is observed to not only be a function of the electron-phonon scattering time and phonon escape time, but also a function of electron temperature. The latter is due to the temperature dependence of the electron and phonon specific heat. Because hot electron bolometers nominally operate at, or slightly above, the critical temperature (TO of the superconducting film, where local resistivity as a function of electron temperature is largest, it follows that the critical temperature of the film plays an important role in determining the FMB mixer gain bandwidth. For an NbN based hot electron bolometer, the maximum predicted gain bandwidth is approximately 5.5 GHz, given a film thickness of 3.5 nm and a Tc=12K.
We have measured the IF impedance and mixer gain bandwidth of a small area phonon cooled hot-electron bolometer in the 0.05-10 GHz range under a variety of bias and LO pumping level conditions. The device used is a twin slot antenna coupled NbN HEB mixer, with a bridge area of 1 μm x 0.15 μm, and a critical temperature of 8.3 K. We model the HEB IF impedance following the work of Nebosis, Semenov, Gousev, and Renk, from now on refered to as the ”NSGR” model. This model is based on the two-temperature model of Perrin-Vanneste, and is found to accurately describe the measured data at different bias and LO pump levels. Three fitting parameters are used in the NSGR model to describe the frequency dependent modulation of the electron temperature; the electron-phonon interaction time τeph, the phonon escape time (into the substrate) τes, and the ratio of the electron and phonon specific heat capacity ce/cph. The described time constants and temperature dependent heat capacity ratio obtained from fitting the model to the measured data agrees well with those reported on for thin NbN films in literature. Using an expression for mixer gain from the NSGR model, but modified to take additional parasitic loss and the complex voltage reflection between mixer and IF load impedance into account, we find when we use the impedance fit parameters τeph, τes, ce/cph, an excellent agreement between measured and modeled HEB conversion gain. Keywords— IF Impedance, phonon cooled hot electron bolometer (pHEB), two-temperature model, ”hot” electrons, Perrin-Vanneste, NSGR model, electron temperature modulation, electron-phonon interaction time, phonon escape time, electro-thermal feedback, complex impedance, HEB mixer conversion gain.
The bandwidth of NbN phonon-cooled hot electron bolometer mixers has been systematically investigated with respect to the film thickness and film quality variation. The films, 2.5 to 10 nm thick, were fabricated on sapphire substrates using DC reactive magnetron sputtering. All devices consisted of several parallel strips, each 1 μ wide and 2 μ long, placed between Ti-Au contact pads. To measure the gain bandwidth we used two identical BWOs operating in the 120-140 GHz frequency range, one functioning as a local oscillator and the other as a signal source. The majority of the measurements were made at an ambient temperature of 4.2 K with optimal LO and DC bias. The maximum 3 dB bandwidth (about 4 GHz) was achieved for the devices made of films which were 2.5-3.5 nm thick, had a high critical temperature, and high critical current density. A theoretical analysis of bandwidth for these mixers based on the two-temperature model gives a good description of the experimental results if one assumes that the electron temperature is equal to the critical temperature.
We report the results of the bandwidth measurements of NbN hot-electron bolometers, perfomied in the terahertz frequency domain at 140 GHz and 660 GHz and in time domain in the optical range at the wavelength of 395 nm.. Our studies were done on 3.5-nm-thick NbN films evaporated on sapphire substrates and patterned into ilin-size microbridges. In order to measure the gain bandwidth, we used two identical BWOs (140 or 660 GHz), one functioning as a local oscillator and the other as a signal source. The bandwidth we achieved was 3.5-4 GHz at 4.2 K with the optimal LO and DC biases. Time-domain measurements with a resolution below 300 fs were performed using an electro-optic sampling system, in the temperature range between 4.2 K to 9 K at various values of the bias current and optical power. The obtained response time of the NbN hot-electron bolometer to —100fs-wide Ti:sapphire laser pulses was about 27 ps, what corresponds to the 5.9 GHz gain bandwidth. Introduction The bandwidth of hot-electron bolometer (HEB) mixers has reached values which are record for bolometers. The gain bandwidth for phonon-cooled NbN HEB mixers of 4 GHz for 140 GHz and 650 GHz frequencies [1, 2] and the noise bandwidth of 8 GHz for 650 GHz [2] have been demonstrated. For diffusion-cooled Nb HEB mixers, the bandwidth has reached 6 GHz, when measured at 20--40 GHz [3]. However, there is a definite practical interest to even further extend the bandwidth of these devices. The possibilities of the HEB mixer technology in this direction are far from being exhausted. For example, the future of the NbN HEB technology requires that critical temperature Tc > 10 K and critical current density j c > 10 6 Akm at 4.2 K are simultaneously obtained for d < 3 nm-thick films M. The reduction of the optimal power of the local oscillator PLID below 100 nW leads to the decrease of the device length down to L < 0.2 pm, which, in turn, should bring an additional cooling channel for hot electrons—diffusion into metal contacts and a further bandwidth extension.
The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.
The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The results of the DSB noire temperature are: 1300 K at 650 GHz, 4700 K at 2.5 TBz and 10000 K at 3.12 THz. The RF bandwidth of the receiver is at least 2.5 THz. The amount of LO power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain is measured to be -9 dB, the total conversion gain -14 dB.