Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

A 100 GHz SIS mixer of Nb/Al-AlOx/Nb junctions

Junji Inatani, Takashi Kasuga, Akira Sakamoto, Hiroyuki Iwashita, Satoshi Kodaira

Published Mar 1, 1987• 19 citations
Publisher

Abstract

We have made an all-refractory SIS mixer with four Nb/Al-AlOx/Nb junctions connected in series. The mixer is designed to operate at 80-120 GHz. The area of each junction is 2.5 × 2.5 μm2. Both these SIS junctions and a mm-wave choke filter are fabricated on a crystalline quartz substrate. These Nb/Al-AlOx/Nb junctions have shown ideal dc-characteristics and clear photon-assisted tunneling steps. RF measurements were made with a mixer mount which had two mechanical tuners. The conversion loss was less than 9 dB for 75-95 GHz. The minimum value was 8 dB. This value will be drastically improved by optimizing the normal resistance of the SIS junctions.

DOI
10.1109/tmag.1987.1065164

Related papers

Very high-current-density Nb/AlN/Nb tunnel junctions for low-noise submillimeter mixers

Jonathan H. Kawamura, David Miller, Jian Chen +4 more

We have fabricated and tested submillimeter-wave superconductor–insulator–superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc≈30 kA cm−2). The junctions have low-resistance-area products (RNA≈5.6 Ω μm2), good subgap-to-normal resistance ratios Rsg/RN≈10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that ωRNC=1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX=110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits.

Applied Physics Letters•Apr 10, 2000•55 citations

Capability of a MM-wave mixer with Nb/Al-AlOx/Nb SIS junction

Takashi Kasuga, Masato Tsuboi, Junji Inatani +2 more

Characteristics of a millimeter-wave mixer with Nb/Al-AlOx/Nb SIS junction were calculated along the 3-port mixer treatment. Signal and intermediate frequency dependences are obtained. The results show that the mixer has conversion gain between signal frequencies of 30 and 250 GHz. Intermediate frequency up to 10 GHz can be used in the USB mode.

IEEE Transactions on Magnetics•Mar 1, 1987•2 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations

A 345 GHz waveguide mixer using an array of four Nb-Al-Al2O3-Nb SIS junctions

Cornelia E. Honingh, M. M. T. M. Dierichs, H. Schaeffer +2 more

An array of four Nb-Al-Al 2 O 3 -Nb SIS junctions in series is used as the mixing element in a waveguide mixer at 345 GHz. The area of one junction is 4 mu m 2 and its normal state resistance is about 12 Omega , yielding at 345 GHz, omega RC approximately 5. The receiver noise temperature below 550 K is between 330 and 375 GHz with best results around 350 K measured with a hot- and cold-load calibration. The conversion loss calculated from the hot/cold measurements ranges from 10.5 to 12.5 dB. The mixer noise temperature is around 200 K, with an instantaneous bandwidth of 2 GHz.

Superconductor Science and Technology•Nov 1, 1991•1 citation

High quality Ta/PbBi tunnel junctions for 85-110 GHz SIS mixer experiments

G.J. Cui, Dean W. Face, Elie K. Track +4 more

We report on the fabrication of small area (1-6 μm2), high critical current density (103-104A/cm2) Ta/Ta oxide/ Pb0.9Bi0.1SIS tunnel junctions and six junction series arrays designed for use as broadband SIS quasiparticle mixers as 85-110 GHz. These junctions have small subgap leakage currents (1 to 5%), and a "sharp" current rise of width ΔV ∼30-50 μV at the sum gap voltage. An RF filter is fabricated on the substrate along with the junctions. The impedance of this filter combined with the junction capacitance is designed to provide a broadband RF match to the mixer over the entire frequency range. A sliding backshort is the only mechanical tuning element. The single junctions as well as arrays are fabricated with a window geometry on fused quartz substrates. The fused quartz substrates require the deposition of a thin amorphous Ge layer which is conducting as room temperature to avoid charging effects during the ion-beam processing steps. Preliminary measurements at 85- 100 GHz show a relatively low gain (-6.9 dB) compared to the performance expected for junctions of this quality. Model calculations suggest that the low gain arises from errors in the implementation of the RF filter design; this can be improved in future work.

IEEE Transactions on Magnetics•Mar 1, 1987•7 citations

SIS Junctions for Millimeter and Submillimeter Wave Mixers

Takashi Noguchi, Toyoaki Suzuki, Tomonori Tamura

We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.

IEICE Transactions on Electronics•Jan 1, 2012•2 citations
We have made an all-refractory SIS mixer with four Nb/Al-AlOx/Nb junctions connected in series. The mixer is designed to operate at 80-120 GHz. The area of each junction is 2.5 × 2.5 μm2. Both these SIS junctions and a mm-wave choke filter are fabricated on a crystalline quartz substrate. These Nb/Al-AlOx/Nb junctions have shown ideal dc-characteristics and clear photon-assisted tunneling steps. RF measurements were made with a mixer mount which had two mechanical tuners. The conversion loss was less than 9 dB for 75-95 GHz. The minimum value was 8 dB. This value will be drastically improved by optimizing the normal resistance of the SIS junctions.
We have fabricated and tested submillimeter-wave superconductor–insulator–superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc≈30 kA cm−2). The junctions have low-resistance-area products (RNA≈5.6 Ω μm2), good subgap-to-normal resistance ratios Rsg/RN≈10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that ωRNC=1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX=110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
An array of four Nb-Al-Al 2 O 3 -Nb SIS junctions in series is used as the mixing element in a waveguide mixer at 345 GHz. The area of one junction is 4 mu m 2 and its normal state resistance is about 12 Omega , yielding at 345 GHz, omega RC approximately 5. The receiver noise temperature below 550 K is between 330 and 375 GHz with best results around 350 K measured with a hot- and cold-load calibration. The conversion loss calculated from the hot/cold measurements ranges from 10.5 to 12.5 dB. The mixer noise temperature is around 200 K, with an instantaneous bandwidth of 2 GHz.
We report on the fabrication of small area (1-6 μm2), high critical current density (103-104A/cm2) Ta/Ta oxide/ Pb0.9Bi0.1SIS tunnel junctions and six junction series arrays designed for use as broadband SIS quasiparticle mixers as 85-110 GHz. These junctions have small subgap leakage currents (1 to 5%), and a "sharp" current rise of width ΔV ∼30-50 μV at the sum gap voltage. An RF filter is fabricated on the substrate along with the junctions. The impedance of this filter combined with the junction capacitance is designed to provide a broadband RF match to the mixer over the entire frequency range. A sliding backshort is the only mechanical tuning element. The single junctions as well as arrays are fabricated with a window geometry on fused quartz substrates. The fused quartz substrates require the deposition of a thin amorphous Ge layer which is conducting as room temperature to avoid charging effects during the ion-beam processing steps. Preliminary measurements at 85- 100 GHz show a relatively low gain (-6.9 dB) compared to the performance expected for junctions of this quality. Model calculations suggest that the low gain arises from errors in the implementation of the RF filter design; this can be improved in future work.
We have developed a process for the fabrication of high-quality Nb/AlOx/Nb tunnel junctions with small area and high current densities for the heterodyne mixers at millimeter and submillimeter wavelengths. Their dc I-V curves are numerically studied, including the broadening of quasiparticle density of states resulting from the existence of an imaginary part of the gap energy of Nb. We have found both experimentally and numerically that the subgap current is strongly dependent on bias voltage at temperatures below 4.2K unlike the prediction of the BCS tunneling theory. It is shown that calculated dc I-V curves taking into account the complex number of the gap energy agree well with those of Nb/AlOx/Nb junctions measured at temperatures from 0.4 to 4.2K. We have successfully built receivers at millimeter and submillimeter wavelengths with the noise temperature as low as 4 times the quantum photon noise, employing those high-quality Nb/AlOx/Nb junctions. Those low-noise receivers are to be installed in the ALMA (Atacama Large Millimeter/Submillimeter Array) telescope and they are going into series production now.