Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1009.0167 · Superconductor Science and Technology

Aluminum hard mask technique for the fabrication of high quality submicron Nb/Al–AlOx/Nb Josephson junctions

Ch Kaiser, J M Meckbach, K S Ilin, Jürgen Lisenfeld, R Schäfer, A V Ustinov, M Siegel

Published Dec 23, 2010• 18 citations
arXivHTMLPDF

Abstract

We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.

DOI
10.1088/0953-2048/24/3/035005

Related papers

Fabrication of high-quality submicron Nb/Al-AlO x /Nb tunnel junctions

Haifeng Yu, Cao Wen-Hui, Zhu Xiao-Bo +6 more

Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.

Chinese Physics B•Aug 1, 2008•7 citations

Nb/AlOx/Nb Josephson Tunnel Junctions Using Electron Beam Evaporation

Atsuki Inoue, Akiyoshi Nakayama, Yoichi Okabe

Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.

Japanese Journal of Applied Physics•Jul 1, 1988•10 citations

High quality refractory Josephson tunnel junctions utilizing thin aluminum layers

Michael Gurvitch, M. A. Washington, Harold A. Huggins

Preparation of high quality all-refractory Josephson tunnel junctions based on Nb/Al-oxide-Nb and Nb/Al-oxide-Al/Nb structures is reported. Critical currents up to 1300 A/cm2 and Vm values up to 35 mV were obtained. The specific capacitance of these junctions is 0.06±0.02 pF/μm2. Junctions were fabricated using standard photolithography and a new plasma etching process coupled with anodization of Nb.

Applied Physics Letters•Mar 1, 1983•567 citations

Overlap junctions for high coherence superconducting qubits

Xian Wu, J. L. Long, H. S. Ku +3 more

Fabrication of sub-micron Josephson junctions is demonstrated using standard processing techniques for high-coherence, superconducting qubits. These junctions are made in two separate lithography steps with normal-angle evaporation. Most significantly, this work demonstrates that it is possible to achieve high coherence with junctions formed on aluminum surfaces cleaned in situ with Ar milling before the junction oxidation. This method eliminates the angle-dependent shadow masks typically used for small junctions. Therefore, this is conducive to the implementation of typical methods for improving margins and yield using conventional CMOS processing. The current method uses electron-beam lithography and an additive process to define the top and bottom electrodes. Extension of this work to optical lithography and subtractive processes is discussed.

arXiv:1705.08993•Applied Physics Letters•Jul 17, 2017•50 citations

Nb/AlOx/Nb trilayer process for the fabrication of submicron Josephson junctions and low-noise dc SQUIDs

Manjul Bhushan, E. M. Macedo

A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.

Applied Physics Letters•Mar 25, 1991•43 citations

Fabrication process of superconducting integrated circuits with submicron Nb/AlO x /Nb junctions using electron-beam direct writing technique

Masahiro Aoyagi, Hiroshi Nakagawa

For enhancing operating speed of a superconducting integrated circuit (IC), the device size must be reduced into the submicron level. For this purpose, we have introduced electron beam (EB) direct writing technique into the fabrication process of a Nb/AlOx/Nb Josephson IC. A two-layer (PMMA/(alpha) M-CMS) resist method called the portable conformable mask (PCM) method was utilized for having a high aspect ratio. The electron cyclotron resonance (ECR) plasma etching technique was utilized. We have fabricated micron or submicron-size Nb/AlOx/Nb Josephson junctions, where the size of the junction was varied from 2 micrometer to 0.5 micrometer at 0.1 micrometer intervals. These junctions were designed for evaluating the spread of the junction critical current. We achieved minimum-to-maximum Ic spread of plus or minus 13% for 0.81-micrometer-square (plus or minus 16% for 0.67-micrometer-square) 100 junctions spreading in 130- micrometer-square area. The size deviation of 0.05 micrometer was estimated from the spread values. We have successfully demonstrated a small-scale logic IC with 0.9-micrometer-square junctions having a 50 4JL OR-gate chain, where 4JL means four junctions logic family. The circuit was designed for measuring the gate delay. We obtained a preliminary result of the OR- gate logic delay, where the minimum delay was 8.6 ps/gate.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 7, 1997•2 citations
We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.
Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.
Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.
Fabrication of sub-micron Josephson junctions is demonstrated using standard processing techniques for high-coherence, superconducting qubits. These junctions are made in two separate lithography steps with normal-angle evaporation. Most significantly, this work demonstrates that it is possible to achieve high coherence with junctions formed on aluminum surfaces cleaned in situ with Ar milling before the junction oxidation. This method eliminates the angle-dependent shadow masks typically used for small junctions. Therefore, this is conducive to the implementation of typical methods for improving margins and yield using conventional CMOS processing. The current method uses electron-beam lithography and an additive process to define the top and bottom electrodes. Extension of this work to optical lithography and subtractive processes is discussed.
A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.
For enhancing operating speed of a superconducting integrated circuit (IC), the device size must be reduced into the submicron level. For this purpose, we have introduced electron beam (EB) direct writing technique into the fabrication process of a Nb/AlOx/Nb Josephson IC. A two-layer (PMMA/(alpha) M-CMS) resist method called the portable conformable mask (PCM) method was utilized for having a high aspect ratio. The electron cyclotron resonance (ECR) plasma etching technique was utilized. We have fabricated micron or submicron-size Nb/AlOx/Nb Josephson junctions, where the size of the junction was varied from 2 micrometer to 0.5 micrometer at 0.1 micrometer intervals. These junctions were designed for evaluating the spread of the junction critical current. We achieved minimum-to-maximum Ic spread of plus or minus 13% for 0.81-micrometer-square (plus or minus 16% for 0.67-micrometer-square) 100 junctions spreading in 130- micrometer-square area. The size deviation of 0.05 micrometer was estimated from the spread values. We have successfully demonstrated a small-scale logic IC with 0.9-micrometer-square junctions having a 50 4JL OR-gate chain, where 4JL means four junctions logic family. The circuit was designed for measuring the gate delay. We obtained a preliminary result of the OR- gate logic delay, where the minimum delay was 8.6 ps/gate.