Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Modeling the dc superconducting quantum interference device coupled to the multiturn input coil

Keiji Enpuku, Keiji Yoshida

Published May 15, 1991• 34 citations
Publisher

Abstract

In order to study the effect of a multiturn input coil on superconducting quantum interference device (SQUID) characteristics, the radio frequency (rf) properties of the coupling circuit between the SQUID coil and the input coil are studied. For the measurement of rf properties of the coupling circuit, the so-called expanded model of the coupling circuit using normal metals was adopted, which is shown to be very useful for this purpose. It is shown that the SQUID coil cannot be expressed by a simple inductance when the SQUID coil is coupled to the input coil, i.e., many resonant structures are observed in rf properties of the coupling circuit. It is also shown that the damping resistance is useful in suppressing the resonant structures. Using the experimental results, a circuit model of the SQUID coupled to the multiturn input coil is proposed.

DOI
10.1063/1.347576

Related papers

Washer Resonances of DC Superconducting Quantum Interference Device Coupled to Multiturn Input Coil

Keiji Enpuku

Properties of washer resonances in dc superconducting quantum interference devices (SQUIDs) coupled to a multiturn input coil have been studied using an expanded model of the coupled SQUID. The condition of resistances required to suppress the washer resonance is clarified. In the coupled SQUID, junction shunt resistances should be determined by taking into account this condition in addition to the conventional condition βc<1, where βc is the McCumber parameter. In the case of small junction capacitances, it is shown that the washer resonance limits the value of junction shunt resistances, and prevents the use of large resistances given by βc<1. In order to solve this problem, a new washer geometry of the SQUID is proposed. From the experiment using the expanded model of the new washer, it is shown that the new washer can control the washer resonances, and enables the use of large resistance in the coupled SQUID. Therefore, the new washer will be useful for the improvement of the performance of the coupled SQUID.

Japanese Journal of Applied Physics•Sep 1, 1993•9 citations

Effect of capacitive feedback on the characteristics of direct current superconducting quantum interference device coupled to a multiturn input coil

Tadashi Minotani, Keiji Enpuku, Y. Kuroki

Distortion of voltage versus flux (V–Φ) relation of a dc superconducting quantum interference device (SQUID) coupled to a multiturn input coil is studied. First, resonant behavior of the coupled SQUID due to the so-called input coil resonance is clarified. It is shown that large rf noise flux is produced by the input coil resonance. This rf flux is added to the SQUID, and results in large rf voltage across the SQUID. In the case where parasitic capacitance exists between the input coil and the ground of the SQUID, this rf voltage produces the rf flux again, i.e., a feedback loop for the rf flux is formed. Taking into account this capacitive feedback, we study the V–Φ relation of the coupled SQUID. Numerical simulation shows that the V–Φ relation is distorted considerably by the feedback mechanism. The simulation result explains well the experimental V–Φ relation of the coupled SQUID. The combination of the input coil resonance with the capacitive feedback is the most likely mechanism for the distorted V–Φ curve of the coupled SQUID. The condition for occurrence of the distorted V–Φ curve due to the capacitive feedback is also obtained, and methods to prevent degradation are discussed.

Journal of Applied Physics•Jul 1, 1997•15 citations

Array of Superconducting Quantum Interference Devices with Multiturn Input Coil

T. Morooka, Hiroaki Myoren, S. Takada +1 more

Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.

Japanese Journal of Applied Physics•May 1, 2004•3 citations

Input impedance of an amplifier based on a dc superconducting quantum interference device

Claude Hilbert, John L. Clarke

The measured input impedance of an amplifier involving a coil tightly coupled to a dc superconducting quantum interference device (SQUID) is found to depend on the current and flux biases of the SQUID. Variations in the input inductance arise from the reflected dynamic inductance of the SQUID, and are in reasonable agreement with the predictions of an analog simulator. Variations in the input resistance, on the other hand, arise from feedback between the output of the SQUID and the input circuit, and are in approximate agreement with the predictions of a simple model.

Applied Physics Letters•Oct 1, 1984•15 citations

Superconducting multiturn flux transformers for radio frequency superconducting quantum interference devices

H. R. Yi, Y. Zhang, Jürgen Schubert +3 more

This article describes three planar layouts of superconducting multiturn flux transformers integrated with a coplanar resonator for radio frequency (rf) superconducting quantum interference device (SQUID) magnetometers. The best magnetic field noise values of 22 and 11.5 fT/Hz1/2 in the white noise regime were obtained for the layout with two input coils and the layout with the labyrinth resonator, respectively. Excess low-frequency noise (about 200 fT/Hz1/2 at 10 Hz) was present. Computer simulation showed that the loss in this trilayer system was dominated by the high loss tangent of the dielectric film used for the separation of the upper and lower superconducting films. The rf coupling coefficient krf between the resonator and the flip-chip-coupled SQUID was also estimated. The values krf2≈14×10−3 obtained for the layout with two input coils, and krf2≈45×10−3 for the layout with the labyrinth resonator were considerably higher than the typical value of krf2≈7×10−3 for the single-layer coplanar resonator. These high coupling coefficients have compensated the somewhat degraded unloaded quality factor of the resonator, thus securing the optimum operation of the rf SQUID.

Journal of Applied Physics•Nov 15, 2000•7 citations

Radio frequency pumped superconducting quantum interference devices with two quantization loops

G.S. Krivoy, H. Koch

Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.

Journal of Applied Physics•Aug 15, 1993•16 citations
In order to study the effect of a multiturn input coil on superconducting quantum interference device (SQUID) characteristics, the radio frequency (rf) properties of the coupling circuit between the SQUID coil and the input coil are studied. For the measurement of rf properties of the coupling circuit, the so-called expanded model of the coupling circuit using normal metals was adopted, which is shown to be very useful for this purpose. It is shown that the SQUID coil cannot be expressed by a simple inductance when the SQUID coil is coupled to the input coil, i.e., many resonant structures are observed in rf properties of the coupling circuit. It is also shown that the damping resistance is useful in suppressing the resonant structures. Using the experimental results, a circuit model of the SQUID coupled to the multiturn input coil is proposed.
Properties of washer resonances in dc superconducting quantum interference devices (SQUIDs) coupled to a multiturn input coil have been studied using an expanded model of the coupled SQUID. The condition of resistances required to suppress the washer resonance is clarified. In the coupled SQUID, junction shunt resistances should be determined by taking into account this condition in addition to the conventional condition βc<1, where βc is the McCumber parameter. In the case of small junction capacitances, it is shown that the washer resonance limits the value of junction shunt resistances, and prevents the use of large resistances given by βc<1. In order to solve this problem, a new washer geometry of the SQUID is proposed. From the experiment using the expanded model of the new washer, it is shown that the new washer can control the washer resonances, and enables the use of large resistance in the coupled SQUID. Therefore, the new washer will be useful for the improvement of the performance of the coupled SQUID.
Distortion of voltage versus flux (V–Φ) relation of a dc superconducting quantum interference device (SQUID) coupled to a multiturn input coil is studied. First, resonant behavior of the coupled SQUID due to the so-called input coil resonance is clarified. It is shown that large rf noise flux is produced by the input coil resonance. This rf flux is added to the SQUID, and results in large rf voltage across the SQUID. In the case where parasitic capacitance exists between the input coil and the ground of the SQUID, this rf voltage produces the rf flux again, i.e., a feedback loop for the rf flux is formed. Taking into account this capacitive feedback, we study the V–Φ relation of the coupled SQUID. Numerical simulation shows that the V–Φ relation is distorted considerably by the feedback mechanism. The simulation result explains well the experimental V–Φ relation of the coupled SQUID. The combination of the input coil resonance with the capacitive feedback is the most likely mechanism for the distorted V–Φ curve of the coupled SQUID. The condition for occurrence of the distorted V–Φ curve due to the capacitive feedback is also obtained, and methods to prevent degradation are discussed.
Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.
The measured input impedance of an amplifier involving a coil tightly coupled to a dc superconducting quantum interference device (SQUID) is found to depend on the current and flux biases of the SQUID. Variations in the input inductance arise from the reflected dynamic inductance of the SQUID, and are in reasonable agreement with the predictions of an analog simulator. Variations in the input resistance, on the other hand, arise from feedback between the output of the SQUID and the input circuit, and are in approximate agreement with the predictions of a simple model.
This article describes three planar layouts of superconducting multiturn flux transformers integrated with a coplanar resonator for radio frequency (rf) superconducting quantum interference device (SQUID) magnetometers. The best magnetic field noise values of 22 and 11.5 fT/Hz1/2 in the white noise regime were obtained for the layout with two input coils and the layout with the labyrinth resonator, respectively. Excess low-frequency noise (about 200 fT/Hz1/2 at 10 Hz) was present. Computer simulation showed that the loss in this trilayer system was dominated by the high loss tangent of the dielectric film used for the separation of the upper and lower superconducting films. The rf coupling coefficient krf between the resonator and the flip-chip-coupled SQUID was also estimated. The values krf2≈14×10−3 obtained for the layout with two input coils, and krf2≈45×10−3 for the layout with the labyrinth resonator were considerably higher than the typical value of krf2≈7×10−3 for the single-layer coplanar resonator. These high coupling coefficients have compensated the somewhat degraded unloaded quality factor of the resonator, thus securing the optimum operation of the rf SQUID.
Conventional rf SQUIDs (superconducting quantum interference devices) consist of a superconducting loop interrupted by one weak link, and when read out via a tank circuit they produce output signals in the order of a few tens of microvolts. When the single weak link is replaced by a dc SQUID (a superconducting loop with two junctions) a so-called double quantization loop SQUID is formed. In this paper it is shown theoretically, and supported experimentally with thin-film devices of three different designs, that the general behaviour can be explained by a simplified picture of the fixed critical current of the single junction of the rf SQUID being replaced by an effective critical current of a dc SQUID loop that is varied by the applied magnetic flux (i.e., we have a rf SQUID with a variable β parameter). A more detailed analysis of the experimental data and the theory of this novel device reveals its interesting nonlinear character and shows the deviations from this simple picture. It is demonstrated experimentally that output signals in the order of ≥1 mV can be obtained with a suitable read-out mode for the tank circuit, a clear advantage when compared to conventional rf SQUIDs. With respect to dc SQUIDs, the coupling to integrated planar input coils will be unproblematic since no microwave resonances should occur in the structures.