Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Effect of capacitive feedback on the characteristics of direct current superconducting quantum interference device coupled to a multiturn input coil

Tadashi Minotani, Keiji Enpuku, Y. Kuroki

Published Jul 1, 1997• 15 citations
Publisher

Abstract

Distortion of voltage versus flux (V–Φ) relation of a dc superconducting quantum interference device (SQUID) coupled to a multiturn input coil is studied. First, resonant behavior of the coupled SQUID due to the so-called input coil resonance is clarified. It is shown that large rf noise flux is produced by the input coil resonance. This rf flux is added to the SQUID, and results in large rf voltage across the SQUID. In the case where parasitic capacitance exists between the input coil and the ground of the SQUID, this rf voltage produces the rf flux again, i.e., a feedback loop for the rf flux is formed. Taking into account this capacitive feedback, we study the V–Φ relation of the coupled SQUID. Numerical simulation shows that the V–Φ relation is distorted considerably by the feedback mechanism. The simulation result explains well the experimental V–Φ relation of the coupled SQUID. The combination of the input coil resonance with the capacitive feedback is the most likely mechanism for the distorted V–Φ curve of the coupled SQUID. The condition for occurrence of the distorted V–Φ curve due to the capacitive feedback is also obtained, and methods to prevent degradation are discussed.

DOI
10.1063/1.365838

Related papers

Array of Superconducting Quantum Interference Devices with Multiturn Input Coil

T. Morooka, Hiroaki Myoren, S. Takada +1 more

Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.

Japanese Journal of Applied Physics•May 1, 2004•3 citations

Modeling the dc superconducting quantum interference device coupled to the multiturn input coil

Keiji Enpuku, Keiji Yoshida

In order to study the effect of a multiturn input coil on superconducting quantum interference device (SQUID) characteristics, the radio frequency (rf) properties of the coupling circuit between the SQUID coil and the input coil are studied. For the measurement of rf properties of the coupling circuit, the so-called expanded model of the coupling circuit using normal metals was adopted, which is shown to be very useful for this purpose. It is shown that the SQUID coil cannot be expressed by a simple inductance when the SQUID coil is coupled to the input coil, i.e., many resonant structures are observed in rf properties of the coupling circuit. It is also shown that the damping resistance is useful in suppressing the resonant structures. Using the experimental results, a circuit model of the SQUID coupled to the multiturn input coil is proposed.

Journal of Applied Physics•May 15, 1991•34 citations

Effect of an input coil microwave resonance on dynamics and noise properties of a dc superconducting quantum interference device operating close to the hysteretic mode

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.

Review of Scientific Instruments•Mar 1, 1999•9 citations

Effect of thermal noise on the characteristics of a high T c superconducting quantum interference device

Keiji Enpuku, Yuri Shimomura, Takanobu Kisu

Effects of thermal noise on the characteristics of the dc superconducting quantum interference device (SQUID) have been studied. Numerical simulation on the SQUID characteristics operating at T=77 K has been performed by taking into account the thermal noise. It is shown that the voltage versus flux relation of the dc SQUID is degraded considerably with the thermal noise. The degradation becomes significant when the inductance of the SQUID increases. Due to this degradation, there exists significant limitation for the range of the inductance available at T=77 K, unlike the case at T=4.2 K. The maximum inductance should be around 200 pH in order to avoid significant degradation of the transfer function. This limited value of the inductance must be taken into account when we realize the SQUID coupled to an input coil. The analytical expression for the degradation of the transfer function due to the thermal noise is also obtained. The theoretical result explains experimental results reported recently.

Journal of Applied Physics•Jun 1, 1993•127 citations

Effect of large dielectric constant of SrTiO3 substrate on the characteristics of high T c dc superconducting quantum interference device

Keiji Enpuku, T. Maruo, Tadashi Minotani

Effects of large dielectric constant of SrTiO3 substrate on the characteristics of high Tc dc superconducting quantum interference device (SQUID) are studied theoretically. It is shown that parasitic capacitance, which is caused by the substrate and distributes along an inductance of the SQUID, cannot be neglected when we use SrTiO3 substrate. Due to the distributed parasitic capacitance, the inductance can no longer be described as lumped element, but behaves like a transmission line when the length of the inductance becomes long. Taking into account the resonant characteristics of the transmission line, we have modified the conventional equivalent circuit of the SQUID, and presented a circuit model for this case. Using numerical simulation, we have clarified quantitatively how the SQUID characteristics are affected by the resonance due to the parasitic capacitance. The obtained results indicate the importance of taking into account the resonance when we use the SrTiO3 substrate, especially for the case of large junction resistance. Numerical simulation of the model cases shows the possibility that the transfer function can be much increased without degrading the flux noise when the SQUID is properly designed. The present theoretical results explain well the experimental results reported recently.

Journal of Applied Physics•Jul 15, 1996•24 citations

Washer Resonances of DC Superconducting Quantum Interference Device Coupled to Multiturn Input Coil

Keiji Enpuku

Properties of washer resonances in dc superconducting quantum interference devices (SQUIDs) coupled to a multiturn input coil have been studied using an expanded model of the coupled SQUID. The condition of resistances required to suppress the washer resonance is clarified. In the coupled SQUID, junction shunt resistances should be determined by taking into account this condition in addition to the conventional condition βc<1, where βc is the McCumber parameter. In the case of small junction capacitances, it is shown that the washer resonance limits the value of junction shunt resistances, and prevents the use of large resistances given by βc<1. In order to solve this problem, a new washer geometry of the SQUID is proposed. From the experiment using the expanded model of the new washer, it is shown that the new washer can control the washer resonances, and enables the use of large resistance in the coupled SQUID. Therefore, the new washer will be useful for the improvement of the performance of the coupled SQUID.

Japanese Journal of Applied Physics•Sep 1, 1993•9 citations
Distortion of voltage versus flux (V–Φ) relation of a dc superconducting quantum interference device (SQUID) coupled to a multiturn input coil is studied. First, resonant behavior of the coupled SQUID due to the so-called input coil resonance is clarified. It is shown that large rf noise flux is produced by the input coil resonance. This rf flux is added to the SQUID, and results in large rf voltage across the SQUID. In the case where parasitic capacitance exists between the input coil and the ground of the SQUID, this rf voltage produces the rf flux again, i.e., a feedback loop for the rf flux is formed. Taking into account this capacitive feedback, we study the V–Φ relation of the coupled SQUID. Numerical simulation shows that the V–Φ relation is distorted considerably by the feedback mechanism. The simulation result explains well the experimental V–Φ relation of the coupled SQUID. The combination of the input coil resonance with the capacitive feedback is the most likely mechanism for the distorted V–Φ curve of the coupled SQUID. The condition for occurrence of the distorted V–Φ curve due to the capacitive feedback is also obtained, and methods to prevent degradation are discussed.
Arrays of dc-superconducting quantum interference devices (dc-SQUIDs) were investigated, in which each dc-SQUID element has a multiturn input coil. The dependence of flux noise on the number of turns of the input coil was studied for current amplifiers. SQUID arrays were fabricated by a Nb/AlO x /Nb Josephson tunnel junction fabrication process. Results show that the flux noise of the SQUID array amplifier does not depend on the turn number of the input coil. A SQUID array amplifier consisting of 128 dc-SQUID elements was fabricated, in which each element had a 7-turn input coil and a mutual inductance between the input coil and the SQUID loop of 460 pH. This amplifier showed an ultrahigh current resolution of 1 pA/Hz0.5 and a maximum input current of 11 µA for signals of 50 kHz, which is sufficient bandwidth for X-ray detection applications. These values correspond to a large dynamic range of 87 dB. The flux-voltage characteristics of this SQUID array, however, showed asymmetric behavior, which originated from electronic resonance in stray capacitance and the mutual inductance between the SQUID loop and the multiturn input coil.
In order to study the effect of a multiturn input coil on superconducting quantum interference device (SQUID) characteristics, the radio frequency (rf) properties of the coupling circuit between the SQUID coil and the input coil are studied. For the measurement of rf properties of the coupling circuit, the so-called expanded model of the coupling circuit using normal metals was adopted, which is shown to be very useful for this purpose. It is shown that the SQUID coil cannot be expressed by a simple inductance when the SQUID coil is coupled to the input coil, i.e., many resonant structures are observed in rf properties of the coupling circuit. It is also shown that the damping resistance is useful in suppressing the resonant structures. Using the experimental results, a circuit model of the SQUID coupled to the multiturn input coil is proposed.
The dynamics and noise of a dc superconducting quantum interference device (SQUID) with the McCumber parameter βc=2πR2IcC/Φ0 close to the unity (where Ic, R, C are the critical current, the shunt resistance, and the capacitance of the Josephson junctions comprising the SQUID, respectively, and Φ0=2.07×10−15 Wb is the magnetic flux quantum) integrated with a planar spiral input coil have been experimentally studied. The length of the spiral input coil was chosen to match its λ/4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance enhances the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, increases the dynamic resistance Rd and the gradient of the flux-to-voltage characteristics ∂V/∂Φ without hysteresis. This relaxes the tolerance for the βc parameter, simplifies the technological process, and improves the yield of devices. A dc SQUID with loop inductance L=31.4 pH, βc=0.72, and a six turn input coil has demonstrated a nondistorted quasisinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of approximately 140 μV peak-to-peak. A spectral density of the intrinsic magnetic flux noise as low as 3.5×10−7 Φ0/Hz1/2 has been measured in the double stage configuration at a temperature of 4.2 K using direct read-out electronics. This corresponds to the intrinsic energy resolution of ε=12.5h. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz1/2 with an input coil inductance of 58 nH. The coupled energy resolution is εc=45h in the white noise region.
Effects of thermal noise on the characteristics of the dc superconducting quantum interference device (SQUID) have been studied. Numerical simulation on the SQUID characteristics operating at T=77 K has been performed by taking into account the thermal noise. It is shown that the voltage versus flux relation of the dc SQUID is degraded considerably with the thermal noise. The degradation becomes significant when the inductance of the SQUID increases. Due to this degradation, there exists significant limitation for the range of the inductance available at T=77 K, unlike the case at T=4.2 K. The maximum inductance should be around 200 pH in order to avoid significant degradation of the transfer function. This limited value of the inductance must be taken into account when we realize the SQUID coupled to an input coil. The analytical expression for the degradation of the transfer function due to the thermal noise is also obtained. The theoretical result explains experimental results reported recently.
Effects of large dielectric constant of SrTiO3 substrate on the characteristics of high Tc dc superconducting quantum interference device (SQUID) are studied theoretically. It is shown that parasitic capacitance, which is caused by the substrate and distributes along an inductance of the SQUID, cannot be neglected when we use SrTiO3 substrate. Due to the distributed parasitic capacitance, the inductance can no longer be described as lumped element, but behaves like a transmission line when the length of the inductance becomes long. Taking into account the resonant characteristics of the transmission line, we have modified the conventional equivalent circuit of the SQUID, and presented a circuit model for this case. Using numerical simulation, we have clarified quantitatively how the SQUID characteristics are affected by the resonance due to the parasitic capacitance. The obtained results indicate the importance of taking into account the resonance when we use the SrTiO3 substrate, especially for the case of large junction resistance. Numerical simulation of the model cases shows the possibility that the transfer function can be much increased without degrading the flux noise when the SQUID is properly designed. The present theoretical results explain well the experimental results reported recently.
Properties of washer resonances in dc superconducting quantum interference devices (SQUIDs) coupled to a multiturn input coil have been studied using an expanded model of the coupled SQUID. The condition of resistances required to suppress the washer resonance is clarified. In the coupled SQUID, junction shunt resistances should be determined by taking into account this condition in addition to the conventional condition βc<1, where βc is the McCumber parameter. In the case of small junction capacitances, it is shown that the washer resonance limits the value of junction shunt resistances, and prevents the use of large resistances given by βc<1. In order to solve this problem, a new washer geometry of the SQUID is proposed. From the experiment using the expanded model of the new washer, it is shown that the new washer can control the washer resonances, and enables the use of large resistance in the coupled SQUID. Therefore, the new washer will be useful for the improvement of the performance of the coupled SQUID.