Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Optics B Quantum and Semiclassical Optics

The response characteristic of a quantum high-pass/low-pass filter for quantum state preparation

Haibo Wang, Satoru Odate, Yongmin Li, Takayoshi Kobayashi

Published Nov 23, 2005• 0 citations
Publisher

Abstract

We analyse the output characteristic of a quantum high-pass/low-pass filter, which was introduced recently (Wang et al 2005 Phys. Rev. A 72 013822). Various responses of quantum filters with different parameters have been calculated. It is possible to apply these quantum circuits in quantum state preparation.
DOI
10.1088/1464-4266/7/12/041

Related papers

Generation of a sub-Poissonian state with quantum high- and low-pass filters

Haibo Wang, Yongmin Li, Satoru Odate +1 more

We introduce a quantum component, the quantum high- and low-pass filter, and analyze its output characteristic. It is shown that a quantum bandpass filter can be achieved by using passive linear optics and projection measurements. Furthermore, we show that the sub-Poissonian state can be generated by using a cascaded quantum low-pass filter and high-pass filter.

Physical Review A•Jul 27, 2005•1 citation

Response characteristic of a quantum high-/low-pass filter

Haibo Wang, Yongmin Li, Satoru Odate +1 more

Conference on Lasers and Electro-Optics•Jan 1, 2005•0 citations

Cascaded low-pass filters for the measurements of DC characteristics of superconducting qubits

Wei Wu, Jianshe Liu, Tiefu Li +3 more

Chinese Science Bulletin (Chinese Version)•Jul 1, 2010•1 citation

Design of an SFQ Microwave Chopper for Controlling Quantum Bits

G. Matsuda, Yuki Yamanashi, Nobuyuki Yoshikawa

A microwave chopper using single-flux-quantum (SFQ) circuits is proposed for the control of quantum bits (qubits). The proposed microwave chopper is composed of a DC/SFQ converter, an SFQ switch and a band-pass filter (BPF). In operation, an externally applied microwave is input to a DC/SFQ converter to generate an SFQ pulse train, which is chopped at high speed by the SFQ switch. The SFQ pulse train is then filtered by the BPF to remove higher harmonics. The transient response, the amplitude and the spectrum of the microwave output from the chopper were examined by circuit simulation, taking into account the thermal noise. The chopper was implemented using the SRL 2.5 kA/cm2Nb standard process and its characteristics were investigated. It was shown that the microwave output could be successfully chopped by the SFQ switch. The amplitude and line width of the microwave output were measured as 15 muV and 2 Hz at 7 GHz.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•14 citations

Signal Processing Methods for Quantum Receivers

Sebastian Kleis, Christian G. Schaeffer

Coherent quantum communication systems face similar problems as classical optical coherent systems. However, the regime of operation as well as the requirements are fundamentally different. We provide an overview about the current methods and challenges.

OSA Advanced Photonics Congress•Jan 1, 2017•0 citations

Robust cryogenic matched low-pass coaxial filters for quantum computing applications

Аnton I. Ivanov, Victor I. Polozov, Vladimir V. Echeistov +5 more

Electromagnetic noise is one of the main external factors decreasing superconducting qubit coherence. Matched coaxial filters can prevent microwave and IR photons' negative influence on superconducting quantum circuits. In this report, we describe the design and fabrication process of matched coaxial filters for noise-sensitive measurements at millikelvin temperatures. A robust transmission coefficient and ultralow reflection loss of −20 dB in the frequency range up to 20 GHz is achieved. Fabricated low-pass filters have linear transmission and reflection characteristics with 3 dB-cutoff frequency of 1.5–2.5 GHz. A method for extracting the propagation constant and filter impedance from scattering parameter measurements is demonstrated. This method is experimentally approved on a filter with a compound of Cu powder and Stycast epoxy resin and a filter filled with ECCOSORB CR-110 epoxy resin. The proposed design and assembly technology are versatile for various compounds and provide highly repeatable geometric and microwave characteristics. Furthermore, we demonstrate that these low-pass coaxial filters can be effectively utilized to improve superconducting qubit relaxation due to suppressing standing waves originating from reflections in control coaxial cables.

arXiv:2210.15301•Applied Physics Letters•Nov 13, 2023•13 citations
A microwave chopper using single-flux-quantum (SFQ) circuits is proposed for the control of quantum bits (qubits). The proposed microwave chopper is composed of a DC/SFQ converter, an SFQ switch and a band-pass filter (BPF). In operation, an externally applied microwave is input to a DC/SFQ converter to generate an SFQ pulse train, which is chopped at high speed by the SFQ switch. The SFQ pulse train is then filtered by the BPF to remove higher harmonics. The transient response, the amplitude and the spectrum of the microwave output from the chopper were examined by circuit simulation, taking into account the thermal noise. The chopper was implemented using the SRL 2.5 kA/cm2Nb standard process and its characteristics were investigated. It was shown that the microwave output could be successfully chopped by the SFQ switch. The amplitude and line width of the microwave output were measured as 15 muV and 2 Hz at 7 GHz.
Electromagnetic noise is one of the main external factors decreasing superconducting qubit coherence. Matched coaxial filters can prevent microwave and IR photons' negative influence on superconducting quantum circuits. In this report, we describe the design and fabrication process of matched coaxial filters for noise-sensitive measurements at millikelvin temperatures. A robust transmission coefficient and ultralow reflection loss of −20 dB in the frequency range up to 20 GHz is achieved. Fabricated low-pass filters have linear transmission and reflection characteristics with 3 dB-cutoff frequency of 1.5–2.5 GHz. A method for extracting the propagation constant and filter impedance from scattering parameter measurements is demonstrated. This method is experimentally approved on a filter with a compound of Cu powder and Stycast epoxy resin and a filter filled with ECCOSORB CR-110 epoxy resin. The proposed design and assembly technology are versatile for various compounds and provide highly repeatable geometric and microwave characteristics. Furthermore, we demonstrate that these low-pass coaxial filters can be effectively utilized to improve superconducting qubit relaxation due to suppressing standing waves originating from reflections in control coaxial cables.