Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Multitone large-signal analysis of superconducting transition-edge sensors for astronomy

Karwan Rostem, S. Withington, D. J. Goldie

Published Aug 1, 2007• 3 citations
Publisher

Abstract

A simple transition-edge sensor (TES) is governed by two coupled, nonlinear equations, which when solved give the behavior of the device given the initial conditions. The two equations describe the full electrical and thermal characteristics of the device and the way in which the device interacts with the external electrical and thermal circuits. To date these coupled nonlinear equations have been solved analytically in the small-signal limit, by linearizing the equations about some operating point. The resulting coupled linear equations contain a wealth of interesting physics, and form the principal tool by which all detectors are currently designed and modeled. In this article we describe a numerical technique for solving the coupled nonlinear equations rigorously, without any assumptions about the magnitudes of the various signals and parameters that determine the behavior of a device. The technique is based on a harmonic balance algorithm that searches, in the frequency domain, for voltage, current, and temperature wave forms that are consistent with the solid-state physics of the device. Indeed, both the small and large signal limits can be simulated, and the full harmonic content of the system retrieved. In this article, we will outline the principal features of the algorithm, and show various results such as I−V curves, saturation when signal power is modulated, impedance response when the bias current is modulated and signal power kept constant, and pulsed signal power analysis that shows the dynamics of a device. Numerous extensions of this fundamental technique are now possible including multitone nonharmonic analysis, large-signal impedance calculation, modeling of complicated thermal circuits, noise models, and frequency-domain multiplexing. We believe that our algorithm will become the principle technique for analyzing the large-signal behavior of all TES detectors and on that basis we are developing computer aided design software.

DOI
10.1063/1.2763976

Related papers

Analysis and Simulation of AC-Biased TES Circuits

Tianshun Wang, Jun-Kang Chen, Xingxiang Zhou

We systematically study the analysis and simulation of ac-biased superconductor transition-edge sensor (TES) circuits. In these ac-biased circuits, the current and voltage of the TES experience large swings in both directions, and small-signal analysis around a dc steady state does not apply. To understand their electrical and thermal behavior, we rely on concepts and techniques from radio-frequency circuit simulation and introduce the periodic steady state and perform periodic ac analysis. We also construct TES device models based on a comprehensive two-fluid physical model and investigate the behavior of ac-biased TES circuits using advanced circuit simulators. By relating our findings to results for the analysis of dc-biased TES circuits, we give appropriate definitions for the current and temperature sensitivity of the TES in ac-biased circuits. Our work not only builds a rigorous foundation for theoretical analysis of ac-biased TES circuits but also introduces powerful simulation techniques valuable for their design and research.

IEEE Transactions on Applied Superconductivity•Sep 3, 2015•3 citations

Multitone quantum simulations of saturating tunnel junction mixers

S. Withington, Phichet Kittara, G. Yassin

When designing instruments for submillimeter-wave astronomy it is important to understand precisely how saturating superconducting tunnel-junction mixers behave. In this article, a procedure is described for calculating the behavior of tunnel-junction circuits when multitone high-level signals are applied. The procedure is based on a full quantum-mechanical description of photon-assisted tunneling, and uses Harmonic Newton to search for a set of voltages and currents that satisfy the circuit equations at every frequency present. A number of illustrative simulations are presented, and it is shown that Harmonic Newton can be used to model saturating superconductor–insulator–superconductor mixers in a robust and numerically efficient manner.

Journal of Applied Physics•Jun 6, 2003•15 citations

Code-division multiplexing of superconducting transition-edge sensor arrays

K. D. Irwin, Michael D. Niemack, Joern Beyer +7 more

Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.

Superconductor Science and Technology•Feb 22, 2010•61 citations

Inter-Site Fluctuation Mechanics and the Tripartite Noise Hierarchy in Transition-Edge Sensors (TES)

James Glenn-Anderson

Transition-Edge Sensors (TES) represent the state-of-the-art in ultra-sensitive cryogenic radiation detection for cosmic microwave background (CMB) polarimetry and sub-millimeter astronomy. Operating within deep cryogenic regimes on the razor-sharp edge of a superconducting transition, these devices exhibit excess low-frequency noise spectra that severely constrain instrumental sensitivity below 10 Hz. Conventional bolometric noise models—relying on classical thermal fluctuation noise (TFNN), phenomenological Hooge parameters, or standard Dutta-Horn thermal activation—fail to capture the anomalous spectral upturns and non-stationary behavior observed in disordered superconducting bilayers (e.g., Ti/Au or Mo/Au). In this work, we present a rigorous, first-principles derivation of inter-site fluctuation mechanics tailored exclusively to the dissipative DC transport regime of Transition-Edge Sensors. We dismantle the historical conflation of TES and kinetic inductance detector (KID) noise models, establishing instead a tripartite noise hierarchy governed by: (1) Quantum Fluctuations, which dictate zero-point phase dispersion and barrier tunneling across disordered microstructures when classical Arrhenius activation freezes out; (2) Superconductive Fluctuations, which drive order-parameter phase dynamics, Cooper-pair density modulation, and the mesoscopic "fluctuation of fluctuations" via the dynamical breathing of normal-superconducting domain boundaries; (3) Classical Thermal Fluctuations, recovered strictly as the high-temperature asymptotic limit. By formulating a coupled stochastic master equation and non-Hermitian dissipation kernels, we derive the exact non-stationary relaxation time distribution and inter-site resistance noise spectral density . We then incorporate this framework into a modified electrothermal feedback (ETF) and Noise Equivalent Power (NEP) formulation, providing an uncompromising theoretical foundation for next-generation astrophysical instrumentation.

•Nov 7, 2026•0 citations

Thermal Design and Characterization of Transition-Edge Sensor (TES) Bolometers for Frequency-Domain Multiplexing

Martin Lueker, Bradford A. Benson, C. L. Chang +10 more

In contemporary cosmic microwave background experiments, bolometric detectors are often background limited, and in this case the sensitivity of instruments can only be improved by increasing the number of background-limited detectors, and so contemporary TES receivers contain as many pixels as possible. Frequency-domain multiplexing (fMUX) is one strategy for reading out many detectors with one SQUID. For any readout system, it is important to carefully evaluate the thermal design of detector, in conjunction with the readout bandwidth, in order to ensure stable electro-thermal feedback (ETF). We demonstrate a novel technique for characterizing the thermal circuit of our detectors, using am AC-bias and the fMUX electronics. This technique is used to study the internal thermal coupling of a TES bolometer. We illustrate how the insights gathered by this technique have been instrumental in improving the stability of our multiplexed detectors for the south pole telescope (SPT).

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•25 citations

Simulating the Behavior of a 230-GHz SIS Mixer Using Multitone Spectral Domain Analysis

John Garrett, Boon-Kok Tan, Faouzi M. Boussaha +2 more

We present a new software package, called QMix, for simulating the behavior of superconductor/insulator/ superconductor (SIS) mixers. The software uses a harmonic balance procedure to calculate the ac voltage across the SIS junction and multitone spectral domain analysis to calculate the quasiparticle tunneling currents. This approach has two major advantages over other simulation techniques: 1) it can include an arbitrary number of higher order harmonics, and 2) it can simulate the effect of multiple strong nonharmonic frequencies. This allows the QMix software to simulate a wide range of SIS mixer operation, including the effects of harmonics in the local-oscillator (LO) signal and gain saturation with respect to the RF signal power. In this article, we compare the simulated results from QMix to the measured performance of a 230-GHz SIS device, both to validate the software and to investigate the experimental data. To begin, we simulated the conversion gain of the mixer and we found excellent agreement with the experimental results. We were also able to recreate the broken photon step effect by adding higher and lower order harmonics to the LO signal. We then simulated a range of incident RF signal powers in order to calculate the gain saturation point. This is an important metric for SIS mixers because we require linear gain for reliable measurements and calibration. In the simulated results, we found both gain compression and gain expansion, which is consistent with other studies. Overall, these examples demonstrate that QMix is a powerful software package that will allow researchers to simulate the performance of SIS mixers, investigate experimental results, and optimize mixer operation. We have made all of the QMix software open-source and we invite others to contribute to the project.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•2 citations
A simple transition-edge sensor (TES) is governed by two coupled, nonlinear equations, which when solved give the behavior of the device given the initial conditions. The two equations describe the full electrical and thermal characteristics of the device and the way in which the device interacts with the external electrical and thermal circuits. To date these coupled nonlinear equations have been solved analytically in the small-signal limit, by linearizing the equations about some operating point. The resulting coupled linear equations contain a wealth of interesting physics, and form the principal tool by which all detectors are currently designed and modeled. In this article we describe a numerical technique for solving the coupled nonlinear equations rigorously, without any assumptions about the magnitudes of the various signals and parameters that determine the behavior of a device. The technique is based on a harmonic balance algorithm that searches, in the frequency domain, for voltage, current, and temperature wave forms that are consistent with the solid-state physics of the device. Indeed, both the small and large signal limits can be simulated, and the full harmonic content of the system retrieved. In this article, we will outline the principal features of the algorithm, and show various results such as I−V curves, saturation when signal power is modulated, impedance response when the bias current is modulated and signal power kept constant, and pulsed signal power analysis that shows the dynamics of a device. Numerous extensions of this fundamental technique are now possible including multitone nonharmonic analysis, large-signal impedance calculation, modeling of complicated thermal circuits, noise models, and frequency-domain multiplexing. We believe that our algorithm will become the principle technique for analyzing the large-signal behavior of all TES detectors and on that basis we are developing computer aided design software.
We systematically study the analysis and simulation of ac-biased superconductor transition-edge sensor (TES) circuits. In these ac-biased circuits, the current and voltage of the TES experience large swings in both directions, and small-signal analysis around a dc steady state does not apply. To understand their electrical and thermal behavior, we rely on concepts and techniques from radio-frequency circuit simulation and introduce the periodic steady state and perform periodic ac analysis. We also construct TES device models based on a comprehensive two-fluid physical model and investigate the behavior of ac-biased TES circuits using advanced circuit simulators. By relating our findings to results for the analysis of dc-biased TES circuits, we give appropriate definitions for the current and temperature sensitivity of the TES in ac-biased circuits. Our work not only builds a rigorous foundation for theoretical analysis of ac-biased TES circuits but also introduces powerful simulation techniques valuable for their design and research.
When designing instruments for submillimeter-wave astronomy it is important to understand precisely how saturating superconducting tunnel-junction mixers behave. In this article, a procedure is described for calculating the behavior of tunnel-junction circuits when multitone high-level signals are applied. The procedure is based on a full quantum-mechanical description of photon-assisted tunneling, and uses Harmonic Newton to search for a set of voltages and currents that satisfy the circuit equations at every frequency present. A number of illustrative simulations are presented, and it is shown that Harmonic Newton can be used to model saturating superconductor–insulator–superconductor mixers in a robust and numerically efficient manner.
Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.
Transition-Edge Sensors (TES) represent the state-of-the-art in ultra-sensitive cryogenic radiation detection for cosmic microwave background (CMB) polarimetry and sub-millimeter astronomy. Operating within deep cryogenic regimes on the razor-sharp edge of a superconducting transition, these devices exhibit excess low-frequency noise spectra that severely constrain instrumental sensitivity below 10 Hz. Conventional bolometric noise models—relying on classical thermal fluctuation noise (TFNN), phenomenological Hooge parameters, or standard Dutta-Horn thermal activation—fail to capture the anomalous spectral upturns and non-stationary behavior observed in disordered superconducting bilayers (e.g., Ti/Au or Mo/Au). In this work, we present a rigorous, first-principles derivation of inter-site fluctuation mechanics tailored exclusively to the dissipative DC transport regime of Transition-Edge Sensors. We dismantle the historical conflation of TES and kinetic inductance detector (KID) noise models, establishing instead a tripartite noise hierarchy governed by: (1) Quantum Fluctuations, which dictate zero-point phase dispersion and barrier tunneling across disordered microstructures when classical Arrhenius activation freezes out; (2) Superconductive Fluctuations, which drive order-parameter phase dynamics, Cooper-pair density modulation, and the mesoscopic "fluctuation of fluctuations" via the dynamical breathing of normal-superconducting domain boundaries; (3) Classical Thermal Fluctuations, recovered strictly as the high-temperature asymptotic limit. By formulating a coupled stochastic master equation and non-Hermitian dissipation kernels, we derive the exact non-stationary relaxation time distribution and inter-site resistance noise spectral density . We then incorporate this framework into a modified electrothermal feedback (ETF) and Noise Equivalent Power (NEP) formulation, providing an uncompromising theoretical foundation for next-generation astrophysical instrumentation.
In contemporary cosmic microwave background experiments, bolometric detectors are often background limited, and in this case the sensitivity of instruments can only be improved by increasing the number of background-limited detectors, and so contemporary TES receivers contain as many pixels as possible. Frequency-domain multiplexing (fMUX) is one strategy for reading out many detectors with one SQUID. For any readout system, it is important to carefully evaluate the thermal design of detector, in conjunction with the readout bandwidth, in order to ensure stable electro-thermal feedback (ETF). We demonstrate a novel technique for characterizing the thermal circuit of our detectors, using am AC-bias and the fMUX electronics. This technique is used to study the internal thermal coupling of a TES bolometer. We illustrate how the insights gathered by this technique have been instrumental in improving the stability of our multiplexed detectors for the south pole telescope (SPT).
We present a new software package, called QMix, for simulating the behavior of superconductor/insulator/ superconductor (SIS) mixers. The software uses a harmonic balance procedure to calculate the ac voltage across the SIS junction and multitone spectral domain analysis to calculate the quasiparticle tunneling currents. This approach has two major advantages over other simulation techniques: 1) it can include an arbitrary number of higher order harmonics, and 2) it can simulate the effect of multiple strong nonharmonic frequencies. This allows the QMix software to simulate a wide range of SIS mixer operation, including the effects of harmonics in the local-oscillator (LO) signal and gain saturation with respect to the RF signal power. In this article, we compare the simulated results from QMix to the measured performance of a 230-GHz SIS device, both to validate the software and to investigate the experimental data. To begin, we simulated the conversion gain of the mixer and we found excellent agreement with the experimental results. We were also able to recreate the broken photon step effect by adding higher and lower order harmonics to the LO signal. We then simulated a range of incident RF signal powers in order to calculate the gain saturation point. This is an important metric for SIS mixers because we require linear gain for reliable measurements and calibration. In the simulated results, we found both gain compression and gain expansion, which is consistent with other studies. Overall, these examples demonstrate that QMix is a powerful software package that will allow researchers to simulate the performance of SIS mixers, investigate experimental results, and optimize mixer operation. We have made all of the QMix software open-source and we invite others to contribute to the project.