Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal de Physique IV (Proceedings)

High-Tc superconducting microbolometer for terahertz applications

C. Ulysse, Alain Gaugue, Aurèle J. L. Adam, Alain Kreisler, Jean-Claude Villégier, Jean-Luc Thomassin

Published May 1, 2002• 1 citation
Publisher

Abstract

\nSuperconducting hot electron bolometer mixers are now a competitive alternative to Schottky diode mixers in the terahertz frequency range because of their ultra wideband (from millimeter waves to visible light), high conversion gain, and low intrinsic noise level. High Tc superconductor materials can be used to make hot electron bolometers and present some advantage in term of operating temperature and cooling. In this paper, we present first a model for the study of superconducting hot electron bolometers responsivity in direct detection mode, in order to establish a firm basis for the design of future THz mixers. Secondly, an original process to realize YBaCuO hot electron bolometer mixers will be described. Submicron YBaCuO superconducting structures are expitaxially sputter deposited on MgO substrates and patterned by using electron beam lithography in combination with optical lithography. Metal masks achieved by electron beam lithography are insuring a good bridge definition and protection during ion etching. Finally, detection experiments are being performed with a laser at 850 nm wavelength, in homodyne mode in order to prove the feasibility and potential performances of these devices.\n

DOI
10.1051/jp420020054

Related papers

YBCO HEB THz mixers

Arvid Hammar, Serguei Cherednichenko, Stella Bevilacqua

We report on an experimental investigation of high-Tc superconducting hot electron bolometer (HEB) mixers of YBCO. These mixers were tested at 100 and 530 GHz LO for a range of temperatures around 77 K. The conversion gain of -32 dB was measured at an LO power of about 1 mW (530 GHz) and 0.3 GHz IF. The mixers were integrated with a logarithmic spiral antenna on a silicon lens, providing a broad frequency coverage (well above 1 THz). To measure the incident RF signal power we used the homodyne responsivity (see abstract "Terahertz response of YBCO HEB homodyne detectors") which is referenced to the input of the silicon lens where the bolometers were glued. Corrections were made for losses in the cryostat window and polarization losses between the signal and antenna. We made the measurements at different temperatures and different LO power levels which were measured using a quasi optical detector at room temperature. The 3 dB gain bandwidth was measured to be about 0.2 GHz. The bolometer bridges have nominal dimensions 1 μm x 2 μm x 50 nm and are fabricated on sapphire substrates using UV photolithography. Backward wave oscillators sources were used at 530 GHz and Gunn diodes at 100 GHz.

•Jan 1, 2011•0 citations

THz Mixing with High-TC Hot Electron Bolometers: A Performance Modeling Assessment for Y-Ba-Cu-O Devices

Romain G. Ladret, Annick F. Degardin, Vishal Jagtap +1 more

Hot electron bolometers (HEB) made from high-TC superconducting YBa2Cu3O7–x (YBCO) oxide nano-constrictions are promising THz mixers, due to their expected wide bandwidth, large mixing gain, and low intrinsic noise. The challenge for YBCO resides, however, in the chemical reactivity of the material and the related aging effects. In this paper, we model and simulate the frequency dependent performance of YBCO HEBs operating as THz mixers. We recall first the main hypotheses of our hot spot model taking into account both the RF frequency effects in the YBCO superconducting transition and the nano-constriction impedance at THz frequencies. The predicted performance up to 4 THz is given in terms of double sideband noise temperature TDSB and conversion gain G. At 2.5 THz for instance, TDSB ≅ 1000 K and G ≅ − 6 dB could be achieved at 12.5 μW local oscillator power. We then consider a standoff target detection scheme and examine the feasibility with YBCO devices. For instance, detection at 3 m through cotton cloth in passive imaging mode could be readily achieved in moderate humidity conditions with 10 K resolution.

Photonics•Jan 25, 2019•6 citations

Superconducting hot electron bolometers for terahertz sensing

Matthew O. Reese

Superconducting Hot Electron Bolometers (HEBs) are good candidates for detecting weak signals in the submillimeter or terahertz range. In this thesis work, a novel fabrication method was developed to make two types of niobium HEBs for different applications. HEBs were designed, fabricated, and then characterized at dc, microwave, and THz frequencies. The first type is a diffusion-cooled HEB, made with a short bridge that determines its cooling time. In this thesis, bridges were typically 400 nm long with bandwidths of about 1 GHz. These diffusion-cooled HEBs were developed as part of a collaboration with the University of Arizona (UA), to develop a proof-of-concept heterodyne array submillimeter camera. Devices were fabricated on thin fused quartz and silica substrates for waveguide coupling in the UA system for the astrophysically interesting 345 and 810 GHz atmospheric windows. The goal of this collaboration is to provide a basis of comparison between Nb diffusion-cooled HEB mixers and superconductorinsulator-superconductor mixers at these frequencies. The second type is a phonon-cooled HEB, made with a ∼3 µm long bridge. Its thermal response is dictated by the electron-phonon relaxation time. These devices were developed in collaboration with Prof. C. Schmuttenmaer’s lab in the Yale Chemistry department, Prof. G. Blake at Caltech,

•Jan 1, 2006•7 citations

Superconducting high-Tc hot electron bolometers used as THz mixers: Predicted performance by hot spot modeling

Romain G. Ladret, Alain Kreisler, Annick F. Degardin

High-TChot electron bolometers (HEB) are promising THz mixers due to their expected wide bandwidth, large mixing gain and low intrinsic noise. In this paper, we have simulated the DC characteristics, conversion loss and noise of YBaCuO HEBs with a hot spot model usually dedicated to low-TCdevices.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Sep 1, 2013•2 citations

Nonlinear THz mixing in YBa 2 Cu 3 O 7 thin film hot electron bolometers

Mark Lee, Chao Te Li, Bascom S. Deaver +3 more

Small volume high-Tc super-conducting YBa2Cu3O7 (YBCO) thin films are used as low power, very wide bandwidth mixers in the frequency range of 75 GHz to 2.5 THz. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEB) coupled to an integrated Au thin-film antenna and transmission line. Near 77 K, these mixers have responsivity as high as 780 V/W using only 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Direct heterodyne and homodyne down-conversion mixing using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss, using only approximately 1 (mu) W of LO power. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. The large gain bandwidth and small power requirements make these high-Tc superconducting mixers an attractive alternative to existing Schottky diode and conventional superconducting receiver technologies.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 22, 1998•2 citations

Gain-Bandwidth Characteristics of High-Tc Superconducting Millimeter-Wave Hot-Electron Bolometer Mixers

Chao-Te Li, Bascom S. Deaver, Robert M. Weikle +3 more

The conversion gain bandwidth characteristics of millimeter-wave mixers using high-Tc superconducting YBa2Cu307 (YBCO) thin films are presented. The YBCO films are patterned into latticecooled hot-electron bolometers (HEB) coupled to an integrated antenna and transmission line. Direct heterodyne and homodyne down-conversion measurements using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. No second plateau in the gain spectrum has been observed, in contrast to other reports. The effective volume of the HEB is believed to be significantly smaller than the physical dimensions of the device. Gershenzon, et al. 1 first proposed the design of a lattice-cooled superconducting hot-electron bolometer (HEB) for use as a low-power, wide-band-width heterodyne mixer at millimeter and submillimeter-wave frequencies. This idea has been successfully implemented using NbN , which shows a conversion gain as high as -15 dB using 1 1.tW of pump power at a temperature of 4.2 K. The ultimate speed and bandwidth of the lattice-cooled HEB is determined by the electron-phonon scattering rate. For this reason, Gershenzon 3 suggested that the high normal-state resistivity of the high-Tc superconductor YBa2Cu307 (YBCO) could indicate a very fast electron inelastic scattering, rate and so make this material an ideal candidate to produce a very wide instantaneous bandwidth lattice-cooled HEB operating at 77 K. The first reports of such mixers at 1.5 gm (Ref. 4) and 9.6 gm (Ref. 5) wavelengths showed a very low intrinsic conversion gain of -77 dB (excluding coupling losses) using a relatively large 0.3 mW of absorbed LO power. However, the gain bandwidth showed a twoplateau structure. A low frequency plateau near -77 dB rolled off near 1 GHz intermediate frequency (IF) but gave way to a second plateau near -90 dB that extended to at least 18 GHz, the upper limit of the measurement. Karasik, et al., have done extensive calculations on the conversion gain properties of lattice-cooled HEB mixers for different mixer dimensions, using a two-temperature model. They found that the conversion gain increases

•Mar 1, 1998•1 citation
\nSuperconducting hot electron bolometer mixers are now a competitive alternative to Schottky diode mixers in the terahertz frequency range because of their ultra wideband (from millimeter waves to visible light), high conversion gain, and low intrinsic noise level. High Tc superconductor materials can be used to make hot electron bolometers and present some advantage in term of operating temperature and cooling. In this paper, we present first a model for the study of superconducting hot electron bolometers responsivity in direct detection mode, in order to establish a firm basis for the design of future THz mixers. Secondly, an original process to realize YBaCuO hot electron bolometer mixers will be described. Submicron YBaCuO superconducting structures are expitaxially sputter deposited on MgO substrates and patterned by using electron beam lithography in combination with optical lithography. Metal masks achieved by electron beam lithography are insuring a good bridge definition and protection during ion etching. Finally, detection experiments are being performed with a laser at 850 nm wavelength, in homodyne mode in order to prove the feasibility and potential performances of these devices.\n
We report on an experimental investigation of high-Tc superconducting hot electron bolometer (HEB) mixers of YBCO. These mixers were tested at 100 and 530 GHz LO for a range of temperatures around 77 K. The conversion gain of -32 dB was measured at an LO power of about 1 mW (530 GHz) and 0.3 GHz IF. The mixers were integrated with a logarithmic spiral antenna on a silicon lens, providing a broad frequency coverage (well above 1 THz). To measure the incident RF signal power we used the homodyne responsivity (see abstract "Terahertz response of YBCO HEB homodyne detectors") which is referenced to the input of the silicon lens where the bolometers were glued. Corrections were made for losses in the cryostat window and polarization losses between the signal and antenna. We made the measurements at different temperatures and different LO power levels which were measured using a quasi optical detector at room temperature. The 3 dB gain bandwidth was measured to be about 0.2 GHz. The bolometer bridges have nominal dimensions 1 μm x 2 μm x 50 nm and are fabricated on sapphire substrates using UV photolithography. Backward wave oscillators sources were used at 530 GHz and Gunn diodes at 100 GHz.
Hot electron bolometers (HEB) made from high-TC superconducting YBa2Cu3O7–x (YBCO) oxide nano-constrictions are promising THz mixers, due to their expected wide bandwidth, large mixing gain, and low intrinsic noise. The challenge for YBCO resides, however, in the chemical reactivity of the material and the related aging effects. In this paper, we model and simulate the frequency dependent performance of YBCO HEBs operating as THz mixers. We recall first the main hypotheses of our hot spot model taking into account both the RF frequency effects in the YBCO superconducting transition and the nano-constriction impedance at THz frequencies. The predicted performance up to 4 THz is given in terms of double sideband noise temperature TDSB and conversion gain G. At 2.5 THz for instance, TDSB ≅ 1000 K and G ≅ − 6 dB could be achieved at 12.5 μW local oscillator power. We then consider a standoff target detection scheme and examine the feasibility with YBCO devices. For instance, detection at 3 m through cotton cloth in passive imaging mode could be readily achieved in moderate humidity conditions with 10 K resolution.
Superconducting Hot Electron Bolometers (HEBs) are good candidates for detecting weak signals in the submillimeter or terahertz range. In this thesis work, a novel fabrication method was developed to make two types of niobium HEBs for different applications. HEBs were designed, fabricated, and then characterized at dc, microwave, and THz frequencies. The first type is a diffusion-cooled HEB, made with a short bridge that determines its cooling time. In this thesis, bridges were typically 400 nm long with bandwidths of about 1 GHz. These diffusion-cooled HEBs were developed as part of a collaboration with the University of Arizona (UA), to develop a proof-of-concept heterodyne array submillimeter camera. Devices were fabricated on thin fused quartz and silica substrates for waveguide coupling in the UA system for the astrophysically interesting 345 and 810 GHz atmospheric windows. The goal of this collaboration is to provide a basis of comparison between Nb diffusion-cooled HEB mixers and superconductorinsulator-superconductor mixers at these frequencies. The second type is a phonon-cooled HEB, made with a ∼3 µm long bridge. Its thermal response is dictated by the electron-phonon relaxation time. These devices were developed in collaboration with Prof. C. Schmuttenmaer’s lab in the Yale Chemistry department, Prof. G. Blake at Caltech,
Small volume high-Tc super-conducting YBa2Cu3O7 (YBCO) thin films are used as low power, very wide bandwidth mixers in the frequency range of 75 GHz to 2.5 THz. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEB) coupled to an integrated Au thin-film antenna and transmission line. Near 77 K, these mixers have responsivity as high as 780 V/W using only 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Direct heterodyne and homodyne down-conversion mixing using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss, using only approximately 1 (mu) W of LO power. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. The large gain bandwidth and small power requirements make these high-Tc superconducting mixers an attractive alternative to existing Schottky diode and conventional superconducting receiver technologies.
The conversion gain bandwidth characteristics of millimeter-wave mixers using high-Tc superconducting YBa2Cu307 (YBCO) thin films are presented. The YBCO films are patterned into latticecooled hot-electron bolometers (HEB) coupled to an integrated antenna and transmission line. Direct heterodyne and homodyne down-conversion measurements using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. No second plateau in the gain spectrum has been observed, in contrast to other reports. The effective volume of the HEB is believed to be significantly smaller than the physical dimensions of the device. Gershenzon, et al. 1 first proposed the design of a lattice-cooled superconducting hot-electron bolometer (HEB) for use as a low-power, wide-band-width heterodyne mixer at millimeter and submillimeter-wave frequencies. This idea has been successfully implemented using NbN , which shows a conversion gain as high as -15 dB using 1 1.tW of pump power at a temperature of 4.2 K. The ultimate speed and bandwidth of the lattice-cooled HEB is determined by the electron-phonon scattering rate. For this reason, Gershenzon 3 suggested that the high normal-state resistivity of the high-Tc superconductor YBa2Cu307 (YBCO) could indicate a very fast electron inelastic scattering, rate and so make this material an ideal candidate to produce a very wide instantaneous bandwidth lattice-cooled HEB operating at 77 K. The first reports of such mixers at 1.5 gm (Ref. 4) and 9.6 gm (Ref. 5) wavelengths showed a very low intrinsic conversion gain of -77 dB (excluding coupling losses) using a relatively large 0.3 mW of absorbed LO power. However, the gain bandwidth showed a twoplateau structure. A low frequency plateau near -77 dB rolled off near 1 GHz intermediate frequency (IF) but gave way to a second plateau near -90 dB that extended to at least 18 GHz, the upper limit of the measurement. Karasik, et al., have done extensive calculations on the conversion gain properties of lattice-cooled HEB mixers for different mixer dimensions, using a two-temperature model. They found that the conversion gain increases