Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Gain-Bandwidth Characteristics of High-Tc Superconducting Millimeter-Wave Hot-Electron Bolometer Mixers

Chao-Te Li, Bascom S. Deaver, Robert M. Weikle, Mark Lee, Rajesh A. Rao, Chang‐Beom Eom

Published Mar 1, 1998• 1 citation
OpenAlex

Abstract

The conversion gain bandwidth characteristics of millimeter-wave mixers using high-Tc superconducting YBa2Cu307 (YBCO) thin films are presented. The YBCO films are patterned into latticecooled hot-electron bolometers (HEB) coupled to an integrated antenna and transmission line. Direct heterodyne and homodyne down-conversion measurements using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. No second plateau in the gain spectrum has been observed, in contrast to other reports. The effective volume of the HEB is believed to be significantly smaller than the physical dimensions of the device. Gershenzon, et al. 1 first proposed the design of a lattice-cooled superconducting hot-electron bolometer (HEB) for use as a low-power, wide-band-width heterodyne mixer at millimeter and submillimeter-wave frequencies. This idea has been successfully implemented using NbN , which shows a conversion gain as high as -15 dB using 1 1.tW of pump power at a temperature of 4.2 K. The ultimate speed and bandwidth of the lattice-cooled HEB is determined by the electron-phonon scattering rate. For this reason, Gershenzon 3 suggested that the high normal-state resistivity of the high-Tc superconductor YBa2Cu307 (YBCO) could indicate a very fast electron inelastic scattering, rate and so make this material an ideal candidate to produce a very wide instantaneous bandwidth lattice-cooled HEB operating at 77 K. The first reports of such mixers at 1.5 gm (Ref. 4) and 9.6 gm (Ref. 5) wavelengths showed a very low intrinsic conversion gain of -77 dB (excluding coupling losses) using a relatively large 0.3 mW of absorbed LO power. However, the gain bandwidth showed a twoplateau structure. A low frequency plateau near -77 dB rolled off near 1 GHz intermediate frequency (IF) but gave way to a second plateau near -90 dB that extended to at least 18 GHz, the upper limit of the measurement. Karasik, et al., have done extensive calculations on the conversion gain properties of lattice-cooled HEB mixers for different mixer dimensions, using a two-temperature model. They found that the conversion gain increases

Related papers

Nonlinear THz mixing in YBa 2 Cu 3 O 7 thin film hot electron bolometers

Mark Lee, Chao Te Li, Bascom S. Deaver +3 more

Small volume high-Tc super-conducting YBa2Cu3O7 (YBCO) thin films are used as low power, very wide bandwidth mixers in the frequency range of 75 GHz to 2.5 THz. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEB) coupled to an integrated Au thin-film antenna and transmission line. Near 77 K, these mixers have responsivity as high as 780 V/W using only 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Direct heterodyne and homodyne down-conversion mixing using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss, using only approximately 1 (mu) W of LO power. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. The large gain bandwidth and small power requirements make these high-Tc superconducting mixers an attractive alternative to existing Schottky diode and conventional superconducting receiver technologies.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 22, 1998•2 citations

Gain bandwidth and noise characteristics of millimeter-wave YBa2Cu3O7 hot-electron bolometer mixers

Chao-Te Li, Bascom S. Deaver, Mark Lee +3 more

Conversion gain bandwidth and noise characteristics are reported for lattice-cooled superconducting YBa2Cu3O7 hot-electron bolometers acting as low-power, wide-bandwidth heterodyne mixers at 75 and 585 GHz. Near 77 K, these mixers show intrinsic conversion gain as high as −16 dB using ∼1 μW of local oscillator power. The measured gain bandwidth is well described by a single Lorentzian with −3 dB frequency of 5–9 GHz. Measurements of output noise combined with conversion gain indicate an optimal input noise temperature of ∼5000 K, significantly lower than calculations predict.

Applied Physics Letters•Sep 21, 1998•17 citations

Wide Bandwidth Far-Infrared Mixing Using a High-T(c) Superconducting Bolometer

Mark Lee, Li, Richard C.

We report on the gain bandwidth and noise characteristics of far-infrared mixers using high-Tc superconducting YBa2Cu3O7 (YBCO) thin films. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEBs) coupled to an integrated antenna and transmission line. Heterodyne and homodyne down- conversion using LO frequencies of 115 GHz and 585 GHz show a device conversion gain of as high as -9.5 dB at 66 K using 1 micro W of LO power. Y-factor noise measurements show a double-sideband noise temperature of 3400 K at 66 K. Both gain and noise bandwidths show a single-pole roll-off with -3 dB point near 10 GHz.

•Sep 29, 2000•3 citations

YBCO HEB THz mixers

Arvid Hammar, Serguei Cherednichenko, Stella Bevilacqua

We report on an experimental investigation of high-Tc superconducting hot electron bolometer (HEB) mixers of YBCO. These mixers were tested at 100 and 530 GHz LO for a range of temperatures around 77 K. The conversion gain of -32 dB was measured at an LO power of about 1 mW (530 GHz) and 0.3 GHz IF. The mixers were integrated with a logarithmic spiral antenna on a silicon lens, providing a broad frequency coverage (well above 1 THz). To measure the incident RF signal power we used the homodyne responsivity (see abstract "Terahertz response of YBCO HEB homodyne detectors") which is referenced to the input of the silicon lens where the bolometers were glued. Corrections were made for losses in the cryostat window and polarization losses between the signal and antenna. We made the measurements at different temperatures and different LO power levels which were measured using a quasi optical detector at room temperature. The 3 dB gain bandwidth was measured to be about 0.2 GHz. The bolometer bridges have nominal dimensions 1 μm x 2 μm x 50 nm and are fabricated on sapphire substrates using UV photolithography. Backward wave oscillators sources were used at 530 GHz and Gunn diodes at 100 GHz.

•Jan 1, 2011•0 citations

Heterodyne measurements of a NbN superconducting hot electron mixer at terahertz frequencies

Pavel A. Yagoubov, M. Kroug, H. Merkel +6 more

The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•6 citations

Low power submillimeter-wave mixing and responsivity properties of YBa2Cu3O7 hot-electron bolometers

Chao-Te Li, Bascom S. Deaver, Mark Lee +3 more

Low power characteristics of superconducting hot-electron bolometric mixers using YBa2Cu3O7 are reported. Near 77 K, these mixers have a responsivity of 780 V/W using 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Heterodyne mixing at 87 GHz shows an overall conversion gain of −47 dB at 1.8 GHz intermediate frequency, using 3.3 mW of incident LO power. The intrinsic conversion gain is estimated to be −16 dB with 1 μW of LO power, close to the calculated optimal values.

Applied Physics Letters•Sep 15, 1997•8 citations
The conversion gain bandwidth characteristics of millimeter-wave mixers using high-Tc superconducting YBa2Cu307 (YBCO) thin films are presented. The YBCO films are patterned into latticecooled hot-electron bolometers (HEB) coupled to an integrated antenna and transmission line. Direct heterodyne and homodyne down-conversion measurements using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. No second plateau in the gain spectrum has been observed, in contrast to other reports. The effective volume of the HEB is believed to be significantly smaller than the physical dimensions of the device. Gershenzon, et al. 1 first proposed the design of a lattice-cooled superconducting hot-electron bolometer (HEB) for use as a low-power, wide-band-width heterodyne mixer at millimeter and submillimeter-wave frequencies. This idea has been successfully implemented using NbN , which shows a conversion gain as high as -15 dB using 1 1.tW of pump power at a temperature of 4.2 K. The ultimate speed and bandwidth of the lattice-cooled HEB is determined by the electron-phonon scattering rate. For this reason, Gershenzon 3 suggested that the high normal-state resistivity of the high-Tc superconductor YBa2Cu307 (YBCO) could indicate a very fast electron inelastic scattering, rate and so make this material an ideal candidate to produce a very wide instantaneous bandwidth lattice-cooled HEB operating at 77 K. The first reports of such mixers at 1.5 gm (Ref. 4) and 9.6 gm (Ref. 5) wavelengths showed a very low intrinsic conversion gain of -77 dB (excluding coupling losses) using a relatively large 0.3 mW of absorbed LO power. However, the gain bandwidth showed a twoplateau structure. A low frequency plateau near -77 dB rolled off near 1 GHz intermediate frequency (IF) but gave way to a second plateau near -90 dB that extended to at least 18 GHz, the upper limit of the measurement. Karasik, et al., have done extensive calculations on the conversion gain properties of lattice-cooled HEB mixers for different mixer dimensions, using a two-temperature model. They found that the conversion gain increases
Small volume high-Tc super-conducting YBa2Cu3O7 (YBCO) thin films are used as low power, very wide bandwidth mixers in the frequency range of 75 GHz to 2.5 THz. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEB) coupled to an integrated Au thin-film antenna and transmission line. Near 77 K, these mixers have responsivity as high as 780 V/W using only 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Direct heterodyne and homodyne down-conversion mixing using local-oscillator frequencies of 75 GHz and 585 GHz show overall conversion gains of -35 dB, which includes a -18 dB coupling loss, using only approximately 1 (mu) W of LO power. The gain bandwidth shows a simple Lorentzian roll-off with -3 dB point of 5 to 8 GHz. The large gain bandwidth and small power requirements make these high-Tc superconducting mixers an attractive alternative to existing Schottky diode and conventional superconducting receiver technologies.
Conversion gain bandwidth and noise characteristics are reported for lattice-cooled superconducting YBa2Cu3O7 hot-electron bolometers acting as low-power, wide-bandwidth heterodyne mixers at 75 and 585 GHz. Near 77 K, these mixers show intrinsic conversion gain as high as −16 dB using ∼1 μW of local oscillator power. The measured gain bandwidth is well described by a single Lorentzian with −3 dB frequency of 5–9 GHz. Measurements of output noise combined with conversion gain indicate an optimal input noise temperature of ∼5000 K, significantly lower than calculations predict.
We report on the gain bandwidth and noise characteristics of far-infrared mixers using high-Tc superconducting YBa2Cu3O7 (YBCO) thin films. The YBCO films are patterned into lattice-cooled hot-electron bolometers (HEBs) coupled to an integrated antenna and transmission line. Heterodyne and homodyne down- conversion using LO frequencies of 115 GHz and 585 GHz show a device conversion gain of as high as -9.5 dB at 66 K using 1 micro W of LO power. Y-factor noise measurements show a double-sideband noise temperature of 3400 K at 66 K. Both gain and noise bandwidths show a single-pole roll-off with -3 dB point near 10 GHz.
We report on an experimental investigation of high-Tc superconducting hot electron bolometer (HEB) mixers of YBCO. These mixers were tested at 100 and 530 GHz LO for a range of temperatures around 77 K. The conversion gain of -32 dB was measured at an LO power of about 1 mW (530 GHz) and 0.3 GHz IF. The mixers were integrated with a logarithmic spiral antenna on a silicon lens, providing a broad frequency coverage (well above 1 THz). To measure the incident RF signal power we used the homodyne responsivity (see abstract "Terahertz response of YBCO HEB homodyne detectors") which is referenced to the input of the silicon lens where the bolometers were glued. Corrections were made for losses in the cryostat window and polarization losses between the signal and antenna. We made the measurements at different temperatures and different LO power levels which were measured using a quasi optical detector at room temperature. The 3 dB gain bandwidth was measured to be about 0.2 GHz. The bolometer bridges have nominal dimensions 1 μm x 2 μm x 50 nm and are fabricated on sapphire substrates using UV photolithography. Backward wave oscillators sources were used at 530 GHz and Gunn diodes at 100 GHz.
The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.
Low power characteristics of superconducting hot-electron bolometric mixers using YBa2Cu3O7 are reported. Near 77 K, these mixers have a responsivity of 780 V/W using 8 nW of local oscillator (LO) power at 585 GHz. The responsivity can be shown to be truly bolometric. Heterodyne mixing at 87 GHz shows an overall conversion gain of −47 dB at 1.8 GHz intermediate frequency, using 3.3 mW of incident LO power. The intrinsic conversion gain is estimated to be −16 dB with 1 μW of LO power, close to the calculated optimal values.