Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Development of epitaxial NbN/MgO/NbN–superconductor-insulator-superconductor mixers for operations over the Nb gap frequency

Akira Kawakami, Yoshinori Uzawa, Zhen Wang

Published Nov 7, 2003• 40 citations
Publisher

Abstract

We have developed fabrication processes for epitaxial NbN/MgO/NbN trilayers and epitaxial NbN/MgO/NbN tunnel junctions. We estimated the junction specific capacitances (CS) for designing fully epitaxial NbN–superconductor-insulator-superconductor (SIS) mixers by using Fiske steps. Tunnel junctions measuring 40×3 and 20×3 μm2 were fabricated, and Fiske steps caused by external magnetic fields were clearly observed in the I–V characteristics. The CS was estimated as a function of the product of the normal-state resistance and the junction area (RNA), and they were 73–120 fF/μm2 at 8800–90 Ω μm2. We fabricated and tested a fully epitaxial NbN/MgO/NbN–SIS mixer. The mixer showed low-noise properties over the Nb gap frequency, and the lowest DSB receiver noise was 260 K at 795 GHz.

DOI
10.1063/1.1625431

Related papers

NbN/MgO/NbN SIS tunnel junctions for submm wave mixers

J. A. Stern, B. D. Hunt, Henry George LeDuc +4 more

The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>

IEEE Transactions on Magnetics•Mar 1, 1989•17 citations

A submillimetre-wave SIS mixer using NbN/MgO/NbN trilayers grown epitaxially on an MgO substrate

Yoshinori Uzawa, Akira Kawakami, Atsushi SAITO +2 more

We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.

Superconductor Science and Technology•Nov 21, 2002•6 citations

Fabrication and testing of NbN/MgO/NbN tunnel junctions for use as high-frequency heterodyne detectors

Jeffrey A. Stern

This thesis describes the development and testing of NbN/MgO/NbN tunnel junctions for use as superconductor-insulator-superconductor (SIS) mixers. SIS mixers are the most sensitive heterodyne detectors in the millimeter wavelength region. Most SIS mixers use Pb alloy tunnel junction. These tunnel junctions have several problems associated with the soft nature of Pb and its low superconducting transition temperature. NbN-based tunnel junctions are being developed to overcome these difficulties. These devices are intended to be used as mixers at millimeter and submillimeter wavelengths. This thesis describes the fabrication process involved in making NbN junctions, and the results of measurements on these devices. The purpose of these measurements is to determine the future possibilities of NbN tunnel junctions as high-frequency mixers. The first chapter is an introduction to SIS mixers and explains how tunnel junction properties affect mixer performance. The basic theory of tunneling and mixing in SIS mixers is first presented. A description of quantum mixer theory is included in this presentation. This theory makes several interesting predictions that cannot be explained using classical theories. This is followed by a description of how real SIS tunnel junctions differ from ideal junctions. The physical origin of these differences is discussed, along with how they affect SIS mixer performance. Finally, the advantages and disadvantages of the various superconducting materials available are discussed. The decision to develop NbN devices is based on these material properties. The second chapter describes the methods used to fabricate small-area NbN/MgO/NbN tunnel junctions. The chapter begins with a description of the various methods that have been used to deposit NbN films. Reactive magnetron sputtering is chosen as the best method for tunnel junction fabrication. Details on the vacuum systems and the methods used for depositing superconducting NbN are discussed. Next, the process used for depositing junction trilayers (NbN/MgO/NbN) is described. The probable growth mode of MgO on NbN is presented. The importance of this growth mode to the junction quality is explained in some detail. Next, standard junction processing steps are reported. The details and limitations of each step are put forth. The standard process allows for the fabrication of 1 [square micron] tunnel junctions. Finally, this chapter discusses several methods of fabaricating submicron junctions that are being pursued. The status of this work is given. The third chapter describes the characterization of NbN films and NbN/Mg0/NbN tunnel junctions. Film properties are described first. The correlation of these properties to deposition conditions is discussed in some detail. Next, values for the various features of the I-V characteristic are given; typical and exceptional values are noted. How these features limit mixer results is described in detail. Several important device attributes were measured using superconducting-quantum-interference-devices (SQUIDs). These attributes are the junction's specific capacitance and the film's magnetic penetration depth. The theory and results of measuring specific capacitance and penetration depth are presented. Following the SQUID results is a large section on RP testing. Mixer tests were made at 205 GHz. The receiver design used, integral inductive tuning circuit used and results are discussed. These results are well understood, with the exception of the temperature dependence of the mixer performance. Finally, measurements of the uniformity of many junctions on a single wafer are presented. The importance of junction uniformity is also described. The final chapter discusses the ultimate limits on NbN mixers, and tells what future work must be done to achieve these limits. The primary high-frequency limit on NbN junctions is the capacitance of NbN/MgO/NbN junctions. The limit imposed by the junction capacitance and circuits used to tune out this capacitance are discussed. Also, the low-frequency limits on NbN junctions are discussed. The status of submicron devices is presented. Junction area is the most immediate limitation on NbN mixer results. The possibility of using other barrier materials to increase the RC speed of NbN junctions is presented. Finally, the possibility of operating NbN junctions at temperatures above 4.2 K is discussed.

•Dec 20, 2004•0 citations

Performance of all-NbN quasi-optical SIS mixers for the terahertz band

Yoshinori Uzawa, Akira Kawakami, Shigehito Miki +1 more

We have designed, fabricated, and tested terahertz superconductor-insulator-superconductor (SIS) mixers having a self-compensated NbN/AlN/NbN tunnel junction and an epitaxially grown NbN/MgO/NbN microstripline. The junction as a distributed element was 0.8-/spl mu/m wide and 2.4-/spl mu/m long, and its current density was 50 kA/cm/sup 2/. The microstripline consisted of a 200-nm-thick NbN ground plane, a 180-nm-thick MgO insulator, and a 350-nm-thick NbN wiring layer. An investigation of the mixer in our receiver configuration showed flat noise characteristics from 870 to 960 GHz. The lowest receiver noise temperature of about 550 K was obtained at 909 GHz, including a 9-/spl mu/m-thick Mylar beam splitter loss and other optical losses. These characteristics suggest that SIS mixers with self-compensated NbN/AlN/NbN junctions and NbN/MgO/NbN microstriplines are appropriate for used in wideband and low-noise operations at terahertz frequencies.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•21 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations

Performance of NbN superconductive tunnel junctions as SIS mixers at 205 GHz

William R. McGrath, J. A. Stern, Hamid Javadi +3 more

Small area (<or=1- mu m/sup 2/), high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 mu m/sup 2/ and critical current density of 5-10 kA/cm/sup 2/ are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. Accurate values of junction capacitance and magnetic penetration depth are required for the proper design of the microstrip. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/ mu m/sup 2/ and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 mu m/sup 3/ and critical current density of 18-25 kA/cm/sup 2/ have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.

IEEE Transactions on Magnetics•Mar 1, 1991•27 citations
We have developed fabrication processes for epitaxial NbN/MgO/NbN trilayers and epitaxial NbN/MgO/NbN tunnel junctions. We estimated the junction specific capacitances (CS) for designing fully epitaxial NbN–superconductor-insulator-superconductor (SIS) mixers by using Fiske steps. Tunnel junctions measuring 40×3 and 20×3 μm2 were fabricated, and Fiske steps caused by external magnetic fields were clearly observed in the I–V characteristics. The CS was estimated as a function of the product of the normal-state resistance and the junction area (RNA), and they were 73–120 fF/μm2 at 8800–90 Ω μm2. We fabricated and tested a fully epitaxial NbN/MgO/NbN–SIS mixer. The mixer showed low-noise properties over the Nb gap frequency, and the lowest DSB receiver noise was 260 K at 795 GHz.
The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 10/sup 4/ A/cm/sup 2/ have been fabricated with V/sub m/ values as high as 65 mV and areas down to 0.1 mu m/sup 2/. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/ mu m/sup 2/. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.>
We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.
This thesis describes the development and testing of NbN/MgO/NbN tunnel junctions for use as superconductor-insulator-superconductor (SIS) mixers. SIS mixers are the most sensitive heterodyne detectors in the millimeter wavelength region. Most SIS mixers use Pb alloy tunnel junction. These tunnel junctions have several problems associated with the soft nature of Pb and its low superconducting transition temperature. NbN-based tunnel junctions are being developed to overcome these difficulties. These devices are intended to be used as mixers at millimeter and submillimeter wavelengths. This thesis describes the fabrication process involved in making NbN junctions, and the results of measurements on these devices. The purpose of these measurements is to determine the future possibilities of NbN tunnel junctions as high-frequency mixers. The first chapter is an introduction to SIS mixers and explains how tunnel junction properties affect mixer performance. The basic theory of tunneling and mixing in SIS mixers is first presented. A description of quantum mixer theory is included in this presentation. This theory makes several interesting predictions that cannot be explained using classical theories. This is followed by a description of how real SIS tunnel junctions differ from ideal junctions. The physical origin of these differences is discussed, along with how they affect SIS mixer performance. Finally, the advantages and disadvantages of the various superconducting materials available are discussed. The decision to develop NbN devices is based on these material properties. The second chapter describes the methods used to fabricate small-area NbN/MgO/NbN tunnel junctions. The chapter begins with a description of the various methods that have been used to deposit NbN films. Reactive magnetron sputtering is chosen as the best method for tunnel junction fabrication. Details on the vacuum systems and the methods used for depositing superconducting NbN are discussed. Next, the process used for depositing junction trilayers (NbN/MgO/NbN) is described. The probable growth mode of MgO on NbN is presented. The importance of this growth mode to the junction quality is explained in some detail. Next, standard junction processing steps are reported. The details and limitations of each step are put forth. The standard process allows for the fabrication of 1 [square micron] tunnel junctions. Finally, this chapter discusses several methods of fabaricating submicron junctions that are being pursued. The status of this work is given. The third chapter describes the characterization of NbN films and NbN/Mg0/NbN tunnel junctions. Film properties are described first. The correlation of these properties to deposition conditions is discussed in some detail. Next, values for the various features of the I-V characteristic are given; typical and exceptional values are noted. How these features limit mixer results is described in detail. Several important device attributes were measured using superconducting-quantum-interference-devices (SQUIDs). These attributes are the junction's specific capacitance and the film's magnetic penetration depth. The theory and results of measuring specific capacitance and penetration depth are presented. Following the SQUID results is a large section on RP testing. Mixer tests were made at 205 GHz. The receiver design used, integral inductive tuning circuit used and results are discussed. These results are well understood, with the exception of the temperature dependence of the mixer performance. Finally, measurements of the uniformity of many junctions on a single wafer are presented. The importance of junction uniformity is also described. The final chapter discusses the ultimate limits on NbN mixers, and tells what future work must be done to achieve these limits. The primary high-frequency limit on NbN junctions is the capacitance of NbN/MgO/NbN junctions. The limit imposed by the junction capacitance and circuits used to tune out this capacitance are discussed. Also, the low-frequency limits on NbN junctions are discussed. The status of submicron devices is presented. Junction area is the most immediate limitation on NbN mixer results. The possibility of using other barrier materials to increase the RC speed of NbN junctions is presented. Finally, the possibility of operating NbN junctions at temperatures above 4.2 K is discussed.
We have designed, fabricated, and tested terahertz superconductor-insulator-superconductor (SIS) mixers having a self-compensated NbN/AlN/NbN tunnel junction and an epitaxially grown NbN/MgO/NbN microstripline. The junction as a distributed element was 0.8-/spl mu/m wide and 2.4-/spl mu/m long, and its current density was 50 kA/cm/sup 2/. The microstripline consisted of a 200-nm-thick NbN ground plane, a 180-nm-thick MgO insulator, and a 350-nm-thick NbN wiring layer. An investigation of the mixer in our receiver configuration showed flat noise characteristics from 870 to 960 GHz. The lowest receiver noise temperature of about 550 K was obtained at 909 GHz, including a 9-/spl mu/m-thick Mylar beam splitter loss and other optical losses. These characteristics suggest that SIS mixers with self-compensated NbN/AlN/NbN junctions and NbN/MgO/NbN microstriplines are appropriate for used in wideband and low-noise operations at terahertz frequencies.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
Small area (<or=1- mu m/sup 2/), high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 mu m/sup 2/ and critical current density of 5-10 kA/cm/sup 2/ are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. Accurate values of junction capacitance and magnetic penetration depth are required for the proper design of the microstrip. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/ mu m/sup 2/ and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 mu m/sup 3/ and critical current density of 18-25 kA/cm/sup 2/ have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.