Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Microwave and Wireless Components Letters

Superconducting 4–8 GHz IF Hybrid for Low Noise mm-Wave Sideband Separation SIS Receiver

Bhushan Billade, Hawal Rashid, Vincent Desmaris, Victor Y. Belitsky

Published Oct 16, 2012• 2 citations
Publisher

Abstract

We present the design and performance of a superconducting 90° hybrid covering a full octave bandwidth from 4 to 8 GHz. The hybrid is designed using the Lange coupler layout. The novel features of this quadrature hybrid include superconducting niobium (Nb) transmission lines, air bridges to connect the fingers of the coupler and a bias-T integrated with the coupler. Our simulations indicate that the amplitude imbalance of the designed hybrid is less than 0.8 dB over the entire 4-8 GHz band with negligible phase imbalance. Experimental verification of the hybrid at 4 K, shows very good agreement between the simulations and the measurement results. The measured amplitude imbalance of the hybrid is less than 0.8 dB over 98% of the band and the maximum phase imbalance is ±4 degrees.

DOI
10.1109/lmwc.2012.2222363

Related papers

Superconducting 4–8-GHz Hybrid Assembly for 2SB Cryogenic THz Receivers

Hawal Rashid, Denis Meledin, Vincent Desmaris +2 more

We present here the design and characterization of an intermediate frequency (IF) assembly comprising a compact 90° hybrid chip (coupled line coupler - Lange coupler- coupled line coupler), two bias-T circuits for biasing the superconductor-insulator-superconductor (SIS) mixers, and two transmission-line circuits. Specifically, the miniaturized three-section hybrid chip fabricated using thin-film technology utilizes superconducting Niobium (Nb) transmission lines, air bridges to connect the fingers of the Lange coupler (middle section), and is complemented with two bias-T circuits with integrated MIM capacitors. The assembly was designed to ensure amplitude and phase imbalances better than 0.6 dB and ±2°, respectively. Experimental verification of the assembly at 4 K shows good agreement between the measurements and simulations with amplitude imbalance of 0.5 dB and maximum phase imbalance of ±2°. The ALMA band-5 (163-211 GHz) receiver will include such assembly. The receiver tests shows sideband rejection ratio better than 15 dB over the entire RF band, i.e., a systematic improvement of 3-9 dB as compared with the previously reported results.

IEEE Transactions on Terahertz Science and Technology•Jan 31, 2014•21 citations

A 4-20 GHz Superconducting 90deg Hybrid Using Capacitively Loaded Coupled Lines for 2SB Heterodyne Receivers

François Joint, Max Behrens, Denis Meledin +10 more

We report the design and cryogenic characterisation of a broadband superconducting 90◦ intermediate-frequency (IF) hybrid covering 4–20 GHz for sideband-separating (2SB) heterodyne receivers. The hybrid is implemented in thin-film niobium using capacitively loaded edge coupled transmission lines, avoiding the air-bridge interconnections required in Lange-coupler layouts while retaining a compact superconducting implementation with low loss and good quadrature balance. Cryogenic measurements using Vector Network Analyser (VNA) show amplitude and phase imbalance better than 0.6 dB and 6◦, respectively, across the full band. When used in a 2SB receiver, this level of IF balance is consistent with the observed image-rejection performance in the 10–20 dB range, for the full receiver. The design supports the development of wide-instantaneous-bandwidth 2SB receivers for millimeter and submillimeter observatories, improving spectral grasp for broadband line surveys and high-redshift line searches.

arXiv:2610.24859•Jun 11, 2026•1 citation

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2014•2 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Design and Performance of a 600–720-GHz Sideband-Separating Receiver Using ${\hbox{AlO}}_{x}$ and AlN SIS Junctions

Fausto Patricio Mena, J. Kooi, Andrey M. Baryshev +6 more

We present the design, modeling, construction, and characterization of a sideband separating heterodyne receiver that covers the frequency range from 600 to 720 GHz. The receiver has been constructed using waveguide technology in the split-block technique. The core of the mixer consists of a quadrature hybrid, two directional couplers to inject the local oscillator signal, two superconductor-insulator-superconductor (SIS) junctions, three signal-termination loads, and two planar IF/bandpass-filter/dc-bias circuits. The instrument that we have constructed presents excellent performance as demonstrated by two important figures of merit: receiver noise temperature and sideband ratio. Across the entire band, the uncorrected single-sideband noise temperature is below 500 K and reaches 190 K at the best operating point. The sideband ratio is greater than 10 dB over most of the frequency operating range. Superconducting junctions containing AlO∞- and AlN-tunnel barriers were tested.

IEEE Transactions on Microwave Theory and Techniques•Dec 9, 2010•21 citations

Design and Characterization of a 211–275 GHz Sideband Separating Mixer for the APEX Telescope

Vessen Vassilev, Doug W. Henke, Igor Lapkin +4 more

We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.

IEEE Microwave and Wireless Components Letters•Jan 1, 2008•22 citations
We present the design and performance of a superconducting 90° hybrid covering a full octave bandwidth from 4 to 8 GHz. The hybrid is designed using the Lange coupler layout. The novel features of this quadrature hybrid include superconducting niobium (Nb) transmission lines, air bridges to connect the fingers of the coupler and a bias-T integrated with the coupler. Our simulations indicate that the amplitude imbalance of the designed hybrid is less than 0.8 dB over the entire 4-8 GHz band with negligible phase imbalance. Experimental verification of the hybrid at 4 K, shows very good agreement between the simulations and the measurement results. The measured amplitude imbalance of the hybrid is less than 0.8 dB over 98% of the band and the maximum phase imbalance is ±4 degrees.
We present here the design and characterization of an intermediate frequency (IF) assembly comprising a compact 90° hybrid chip (coupled line coupler - Lange coupler- coupled line coupler), two bias-T circuits for biasing the superconductor-insulator-superconductor (SIS) mixers, and two transmission-line circuits. Specifically, the miniaturized three-section hybrid chip fabricated using thin-film technology utilizes superconducting Niobium (Nb) transmission lines, air bridges to connect the fingers of the Lange coupler (middle section), and is complemented with two bias-T circuits with integrated MIM capacitors. The assembly was designed to ensure amplitude and phase imbalances better than 0.6 dB and ±2°, respectively. Experimental verification of the assembly at 4 K shows good agreement between the measurements and simulations with amplitude imbalance of 0.5 dB and maximum phase imbalance of ±2°. The ALMA band-5 (163-211 GHz) receiver will include such assembly. The receiver tests shows sideband rejection ratio better than 15 dB over the entire RF band, i.e., a systematic improvement of 3-9 dB as compared with the previously reported results.
We report the design and cryogenic characterisation of a broadband superconducting 90◦ intermediate-frequency (IF) hybrid covering 4–20 GHz for sideband-separating (2SB) heterodyne receivers. The hybrid is implemented in thin-film niobium using capacitively loaded edge coupled transmission lines, avoiding the air-bridge interconnections required in Lange-coupler layouts while retaining a compact superconducting implementation with low loss and good quadrature balance. Cryogenic measurements using Vector Network Analyser (VNA) show amplitude and phase imbalance better than 0.6 dB and 6◦, respectively, across the full band. When used in a 2SB receiver, this level of IF balance is consistent with the observed image-rejection performance in the 10–20 dB range, for the full receiver. The design supports the development of wide-instantaneous-bandwidth 2SB receivers for millimeter and submillimeter observatories, improving spectral grasp for broadband line surveys and high-redshift line searches.
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
Design and Performance of a 600–720-GHz Sideband-Separating Receiver Using AlOx{\hbox{AlO}}_{x}AlOx​ and AlN SIS Junctions
We present the design, modeling, construction, and characterization of a sideband separating heterodyne receiver that covers the frequency range from 600 to 720 GHz. The receiver has been constructed using waveguide technology in the split-block technique. The core of the mixer consists of a quadrature hybrid, two directional couplers to inject the local oscillator signal, two superconductor-insulator-superconductor (SIS) junctions, three signal-termination loads, and two planar IF/bandpass-filter/dc-bias circuits. The instrument that we have constructed presents excellent performance as demonstrated by two important figures of merit: receiver noise temperature and sideband ratio. Across the entire band, the uncorrected single-sideband noise temperature is below 500 K and reaches 190 K at the best operating point. The sideband ratio is greater than 10 dB over most of the frequency operating range. Superconducting junctions containing AlO∞- and AlN-tunnel barriers were tested.
We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.