Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Microwave and Wireless Components Letters

Design and Characterization of a 211–275 GHz Sideband Separating Mixer for the APEX Telescope

Vessen Vassilev, Doug W. Henke, Igor Lapkin, Olle Nyström, Raquel Rodriguez Monje, Alexey Pavolotsky, Victor Y. Belitsky

Published Jan 1, 2008• 22 citations
Publisher

Abstract

We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.

DOI
10.1109/lmwc.2007.912026

Related papers

A 211-275 GHz Sideband Separating SIS Mixer for APEX

Vessen Vassilev, Raquel Rodriguez Monje, Alexey Pavolotsky +3 more

We present the results of the development and characterization of the sideband separating (2SB) SIS mixer for the APEX band 1, 211-275 GHz.All mixer components, except the IF hybrid, are integrated into a single mixer block. The sideband separation is achieved by using a quadrature scheme where a local oscillator (LO) pumps two identical SIS mixers. The RF power is divided using a waveguide branch line coupler and directed with 900 phase difference to the ends of the substrate, where each path is coupled to the mixer chip through a waveguide to microstrip transition. Preliminary tests of this 2SB mixer show a sideband suppression ratio of about 12 dB and a typical SSB noise temperature of 80K.

Softwaretechnik-Trends•May 1, 2006•0 citations

Design and Performance of a Sideband Separating SIS Mixer for 800–950 GHz

Andrey V. Khudchenko, M. Yu. Fominsky, Christopher Heiter +11 more

We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.

IEEE Transactions on Terahertz Science and Technology•Sep 2, 2019•21 citations

A 0.5 THz Sideband Separation SIS Mixer for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +6 more

Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.

•Apr 1, 2008•4 citations

A 385 to 500-GHz SIS mixer the for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +2 more

The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•5 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

Performance of a sideband separating SIS mixer for 85-115 GHz

Vessen Vassilev, Victor Y. Belitsky, Christophe Risacher +3 more

We present results of the development and measurements of a heterodyne sideband separating SIS mixer for 85-115 GHz band. The sideband separation is achieved by using a quadrature scheme where a local oscillator (LO) pumps two identical mixer junctions with 90° phase difference. A key component in the mixer is a waveguide to microstrip double probe transition used as a power divider to split the input RF signal and to provide transition from waveguide to microstrip line. The double probe transition enables the integration of all mixer components on a single compact substrate. The design also involves coupled lines directional couplers to introduce the LO power to the mixer junctions. An additional pair of SIS junctions is used to provide termination loads for the idle ports of the couplers. Several mixer chips were tested and similar and consistent performance was obtained. The best single sideband noise temperature is below 40 K with IF bandwidth 3.4-4.6 GHz. The sideband suppression ratio is better than 12 dB for both sidebands across the entire RF band. The mixer was also successfully tested with 4-8 GHz IF band. In this paper we present complete mixer characterization data.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 8, 2004•0 citations
We present the final results of the development and characterization of the sideband separating superconductor-insulator-superconductor (SIS) mixer for the APEX telescope band 1 (211-275 GHz). The sideband separation is achieved by using a quadrature scheme where the radio frequency (RF) and a local oscillator (LO) power are applied to two identical double sideband SIS mixers. All mixer components, including the LO and RF distribution circuitry, are integrated into a single mixer block. To achieve a compact design we developed a superconducting Lange coupler, based on Nb thin film, which is used as an intermediate frequency hybrid. Typical single sideband noise temperature of 100 K and sideband rejection ratio of about 12 dB and are measured.
We present the results of the development and characterization of the sideband separating (2SB) SIS mixer for the APEX band 1, 211-275 GHz.All mixer components, except the IF hybrid, are integrated into a single mixer block. The sideband separation is achieved by using a quadrature scheme where a local oscillator (LO) pumps two identical SIS mixers. The RF power is divided using a waveguide branch line coupler and directed with 900 phase difference to the ends of the substrate, where each path is coupled to the mixer chip through a waveguide to microstrip transition. Preliminary tests of this 2SB mixer show a sideband suppression ratio of about 12 dB and a typical SSB noise temperature of 80K.
We present the design and results of characterization of a new sideband separating (2SB) mixer for 800-950 GHz, based on superconductor-insulator-superconductor (SIS) junctions. This is the first waveguide 2SB SIS mixer demonstrated at such a high frequency. The design is following the classical quadrature hybrid architecture, meanwhile additional attention was put on the reduction of reflections in the RF structure in order to minimize the RF imbalance, to achieve a high image rejection ratio (IRR). The RF waveguide block was manufactured by micromilling and populated by single-ended SIS mixers developed earlier for upgrade of the CHAMP+ high-band array on the APEX telescope. These SIS mixers have double-sideband (DSB) noise temperatures from 210 to 400 K. The assembled 2SB mixer yields a SSB noise temperature from 450 to 900 K, with an IRR above 15 dB in 95% of the band. Comparing the DSB and the SSB sensitivities, we find that the waveguide losses are as low as expected and do not exceed 0.6 dB. The presented mixer is a prototype for use in a 2SB dual polarization receiver planned for deployment on the APEX telescope.
Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.
The Atacama Pathfinder EXperiment (APEX) is a 12 m antenna operating at the Atacama Desert on the Chilean Andes at about 5000 m altitude. APEX would be equipped with a suit of single-pixel heterodyne receivers covering 211 - 1500 GHz frequency range. We present here a design of a sideband-separating superconductor-insulator-superconductor (SIS) mixer for the APEX, receiver Band 3, operating in 385 - 500 GHz band. The receiver uses quadrature scheme with the RF signal passing via a 90-degree waveguide 3 dB hybrid and the LO is divided by a waveguide E-plane Y-junction. The outputs of the waveguide hybrid are coupled to the mixer SIS junctions through an E-probe with integrated bias-T. For the LO coupler, conventional branch waveguide couplers are difficult to manufacture at this high frequency with required accuracy as the branch waveguides become extremely narrow. In order to solve this problem, we propose an on-chip LO injection, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made of superconducting lines, which gives almost a lossless solution and provides fabrication accuracy better than 0.5 μm by using optical lithography only. Furthermore, the mixer design includes a novel component, an ellipse termination for the idle LO port, made of thin-film resistive material with sheet resistance equal to the transmission line characteristic impedance, which gives very broadband performance using extremely compact area.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We present results of the development and measurements of a heterodyne sideband separating SIS mixer for 85-115 GHz band. The sideband separation is achieved by using a quadrature scheme where a local oscillator (LO) pumps two identical mixer junctions with 90° phase difference. A key component in the mixer is a waveguide to microstrip double probe transition used as a power divider to split the input RF signal and to provide transition from waveguide to microstrip line. The double probe transition enables the integration of all mixer components on a single compact substrate. The design also involves coupled lines directional couplers to introduce the LO power to the mixer junctions. An additional pair of SIS junctions is used to provide termination loads for the idle ports of the couplers. Several mixer chips were tested and similar and consistent performance was obtained. The best single sideband noise temperature is below 40 K with IF bandwidth 3.4-4.6 GHz. The sideband suppression ratio is better than 12 dB for both sidebands across the entire RF band. The mixer was also successfully tested with 4-8 GHz IF band. In this paper we present complete mixer characterization data.