Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Towards shot noise-limited detection of a Single-Electron Transistor

Benedetta Camarota

Published Jan 8, 2008• 0 citations
OpenAlex

Abstract

A Single-Electron Transistor (SET) is a highly sensitive charge amplifier based on the Coulomb blockade that can operate near the quantum limit: amplification can be accomplished with a back-action close to that required by the uncertainty principle. Its charge sensitivity is ultimately limited to about 1micre/sqrt(Hz) by the shot noise in the source-drain current. Despite the fact that such sensitivity has been approached by some, the shot-noise limit has yet to be reached for either the SET and its RF version, the RF-SET. A scheme is proposed and realized in this thesis for the shot noise-limited detection of a Single-Electron Transistor, based on a DC-SQUID impedance-matched with a DC-biased SET. SQUIDs can operate at the quantum limit, and a microstrip SQUID amplifier has already been demonstrated to operate at almost twice the quantum-limited noise temperature at about 500MHz by M. Muck and collaborators, with a sensitivity sufficient to resolve the SET shot noise. The device has been fabricated and characterized. A 50KOhm resistor has been used as a noise source at low temperature and the measured noise levels have been estimated. Moreover, the detection noise temperature of about 110mK was derived corresponding to a current sensitivity of about 8fA/sqrt(Hz) for the detection of a 100KOhm resistor.

Related papers

Near-Quantum-Limited Operation of a Charge-Sensitive Electrical Amplifier

A. J. Rimberg, Wei Wei Xue, Zhongqing Ji +2 more

Here, we report the operation of a superconducting single-electron transistor (S-SET) as a fast and nearly quantum-limited charge-sensitive amplifier. By operating the S-SET such that Cooper pair tunneling is resonant across both of its tunnel junctions, we are able to achieve an excellent charge sensitivity of δq = 1.6 × 10-6e/√(Hz), while also minimizing back action. We find that near its optimal operating point, the S-SET can have both a very low noise temperature Tn≈ 50 mK and a large power gain ASET>;>; 1. These results indicate that our S-SET operates within a factor of 2 of the quantum limit.

IEEE Transactions on Nanotechnology•Jan 1, 2010•0 citations

Towards the quantum limit: A Single Electron Transistor analysis

Zhongqing Ji

The Single Electron Transistor (SET), especially its variation the radio frequency single electron transistor (RF-SET), is a fast and ultra-sensitive electrometer working in the vicinity of the quantum limit. In this thesis, the theory and techniques related to the SET in the normal state and the superconducting state are introduced The thesis focuses especially on our efforts of improving the sensitivity of superconducting RF-SET, including: the design and fabrication of an all superconducting near loss-less matching network for improving the RF modulation, our early investigation of the sensitivity and linearity of a superconducting SET (S-SET) subject to quantum fluctuations of quasiparticles and Cooper pairs under different tunneling mechanisms, and our recent work approaching the quantum sensitivity limit using a double Josephson quasiparticle (DJQP) cycle of a S-SET. Using an effective bath description, we have found that the S-SET provides damping of the resonator modes proportional to its differential conductance, and has an effective temperature that can be well below both the ambient temperature and the energy scale of the bias voltage. In the region of negative differential conductance (NDC), the S-SET shows negative damping and a negative temperature. In the final part of the thesis, I have demonstrated our first application of an RF-SET for real-time detection of electron tunneling through a quantum dot.

•Jan 1, 2008•1 citation

Toward a quantum-limited charge detector

Nadia Court, D. J. Reilly, Tilo M. Buehler +2 more

The radio-frequency single-electron-transistor (rf-SET) is an electrometer that can sense a fraction of an electron charge on microsecond timescales. At present this device is prevented from reaching quantum limits by the noise contribution of the post-amplifier, generally a cryogenic high-electron mobility transistor (HEMT). We present results to date in our effort to construct an alternative post-amplifier based on the dc superconducting quantum interference device (SQUID). These SQUID-based amplifiers, which are fabricated in aluminium via electron beam lithography and shadow mask evaporation open the possibility of near-quantum-limited electrometry with the rf-SET.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 28, 2005•1 citation

Development and study of charge sensors for fast charge detection in quantum dots

Madhu Thalakulam

Charge detection at microsecond time-scales has far reaching consequences in both technology and in our understanding of electron dynamics in nanoscale devices such as quantum dots. Radio-frequency superconducting single electron transistors (RF-SET) and quantum point contacts (QPC) are ultra sensitive charge sensors operating near the quantum limit. The operation of RF-SETs outside the superconducting gap has been a topic of study; the sub-gap operation, especially in the presence of large quantum fluctuations of quasiparticles remains largely unexplored, both theoretically and experimentally. We have investigated the effects of quantum fluctuations of quasiparticles on the operation of RF-SETs for large values of the quasiparticle cotunneling parameter alpha = 8EJ/Ec, where EJ and Ec are the Josephson and charging energies. We find that, for alpha > 1, sub-gap RF-SET operation is still feasible despite quantum fluctuations that wash out quasiparticle tunneling thresholds. Such RF-SETs show linearity and signal-to-noise ratio superior to those obtained when quantum fluctuations are weak, while still demonstrating excellent charge sensitivity.\nWe have operated a QPC charge detector in a radio frequency mode that allows fast charge detection in a bandwidth of several megahertz. The noise limiting the sensitivity of the charge detector is not the noise of a secondary amplifier, but the non-equilibrium device noise of the QPC itself. The noise power averaged over a measurement bandwidth of about 10MHz around the carrier frequency is in agreement with the theory of photon-assisted shot noise. Frequency-resolved measurements, however show several significant discrepancies with the theoretical predictions. The measurement techniques developed can also be used to investigate the noise of other semiconductor nanostructures such as quantum dots in the Kondo regime.\nA study of the noise characteristics alone can not determine whether the device is operating at the quantum limit; a characterization of back action is also necessary. The inelastic current through a double quantum dot system (DQD) is sensitive to the spectral density of voltage fluctuations in its electromagnetic environment. Electrical transport studies on a DQD system electrostatically coupled to an SET shows qualitative evidence of back-action of SET. The design and fabrication of a few electron DQD device with integrated RF-SET and QPC charge sensors for the study of back action of the sensors and real-time electron dynamics in the DQD are also discussed.

•Jan 1, 2007•0 citations

Radio-frequency single-electron transistor: Toward the shot-noise limit

A. Aassime, David Gunnarsson, Kevin Bladh +2 more

We have fabricated an aluminum single-electron transistor and characterized it at frequencies up to 10 MHz by measuring the reflected signal from a resonant tank in which the transistor is embedded. We measured the charge sensitivity of this radio-frequency single-electron transistor to be 3.2×10−6 e/Hz, which corresponds to the uncoupled energy sensitivity of 4.8 ℏ. Our measurements indicate that with further improvements, the radio-frequency single-electron transistor could reach the shot-noise limit estimated to be about 1 ℏ.

Applied Physics Letters•Dec 10, 2001•87 citations

Radio-frequency operation of a double-island single-electron transistor

R. Brenner, Tilo M. Buehler, D. J. Reilly

We present results on a double-island single-electron transistor (DISET) operated at radio frequency (rf) for the fast and highly sensitive detection of charge motion in the solid state. Using an intuitive definition for the charge sensitivity, we compare a DISET to a conventional single-electron transistor (SET). We find that a DISET can be more sensitive than a SET for identical, minimum device resistances in the Coulomb blockade regime. This is of particular importance for rf operation, where ideal impedance matching to 50-Ω transmission lines is only possible for a limited range of device resistances. We report a charge sensitivity of 5.6×10−6e∕Hz for a rf-DISET, together with a demonstration of the single-shot detection of small (⩽0.1e) charge signals on microsecond time scales.

arXiv:cond-mat/0409046•Journal of Applied Physics•Dec 30, 2004•7 citations
A Single-Electron Transistor (SET) is a highly sensitive charge amplifier based on the Coulomb blockade that can operate near the quantum limit: amplification can be accomplished with a back-action close to that required by the uncertainty principle. Its charge sensitivity is ultimately limited to about 1micre/sqrt(Hz) by the shot noise in the source-drain current. Despite the fact that such sensitivity has been approached by some, the shot-noise limit has yet to be reached for either the SET and its RF version, the RF-SET. A scheme is proposed and realized in this thesis for the shot noise-limited detection of a Single-Electron Transistor, based on a DC-SQUID impedance-matched with a DC-biased SET. SQUIDs can operate at the quantum limit, and a microstrip SQUID amplifier has already been demonstrated to operate at almost twice the quantum-limited noise temperature at about 500MHz by M. Muck and collaborators, with a sensitivity sufficient to resolve the SET shot noise. The device has been fabricated and characterized. A 50KOhm resistor has been used as a noise source at low temperature and the measured noise levels have been estimated. Moreover, the detection noise temperature of about 110mK was derived corresponding to a current sensitivity of about 8fA/sqrt(Hz) for the detection of a 100KOhm resistor.
Here, we report the operation of a superconducting single-electron transistor (S-SET) as a fast and nearly quantum-limited charge-sensitive amplifier. By operating the S-SET such that Cooper pair tunneling is resonant across both of its tunnel junctions, we are able to achieve an excellent charge sensitivity of δq = 1.6 × 10-6e/√(Hz), while also minimizing back action. We find that near its optimal operating point, the S-SET can have both a very low noise temperature Tn≈ 50 mK and a large power gain ASET>;>; 1. These results indicate that our S-SET operates within a factor of 2 of the quantum limit.
The Single Electron Transistor (SET), especially its variation the radio frequency single electron transistor (RF-SET), is a fast and ultra-sensitive electrometer working in the vicinity of the quantum limit. In this thesis, the theory and techniques related to the SET in the normal state and the superconducting state are introduced The thesis focuses especially on our efforts of improving the sensitivity of superconducting RF-SET, including: the design and fabrication of an all superconducting near loss-less matching network for improving the RF modulation, our early investigation of the sensitivity and linearity of a superconducting SET (S-SET) subject to quantum fluctuations of quasiparticles and Cooper pairs under different tunneling mechanisms, and our recent work approaching the quantum sensitivity limit using a double Josephson quasiparticle (DJQP) cycle of a S-SET. Using an effective bath description, we have found that the S-SET provides damping of the resonator modes proportional to its differential conductance, and has an effective temperature that can be well below both the ambient temperature and the energy scale of the bias voltage. In the region of negative differential conductance (NDC), the S-SET shows negative damping and a negative temperature. In the final part of the thesis, I have demonstrated our first application of an RF-SET for real-time detection of electron tunneling through a quantum dot.
The radio-frequency single-electron-transistor (rf-SET) is an electrometer that can sense a fraction of an electron charge on microsecond timescales. At present this device is prevented from reaching quantum limits by the noise contribution of the post-amplifier, generally a cryogenic high-electron mobility transistor (HEMT). We present results to date in our effort to construct an alternative post-amplifier based on the dc superconducting quantum interference device (SQUID). These SQUID-based amplifiers, which are fabricated in aluminium via electron beam lithography and shadow mask evaporation open the possibility of near-quantum-limited electrometry with the rf-SET.
Charge detection at microsecond time-scales has far reaching consequences in both technology and in our understanding of electron dynamics in nanoscale devices such as quantum dots. Radio-frequency superconducting single electron transistors (RF-SET) and quantum point contacts (QPC) are ultra sensitive charge sensors operating near the quantum limit. The operation of RF-SETs outside the superconducting gap has been a topic of study; the sub-gap operation, especially in the presence of large quantum fluctuations of quasiparticles remains largely unexplored, both theoretically and experimentally. We have investigated the effects of quantum fluctuations of quasiparticles on the operation of RF-SETs for large values of the quasiparticle cotunneling parameter alpha = 8EJ/Ec, where EJ and Ec are the Josephson and charging energies. We find that, for alpha > 1, sub-gap RF-SET operation is still feasible despite quantum fluctuations that wash out quasiparticle tunneling thresholds. Such RF-SETs show linearity and signal-to-noise ratio superior to those obtained when quantum fluctuations are weak, while still demonstrating excellent charge sensitivity.\nWe have operated a QPC charge detector in a radio frequency mode that allows fast charge detection in a bandwidth of several megahertz. The noise limiting the sensitivity of the charge detector is not the noise of a secondary amplifier, but the non-equilibrium device noise of the QPC itself. The noise power averaged over a measurement bandwidth of about 10MHz around the carrier frequency is in agreement with the theory of photon-assisted shot noise. Frequency-resolved measurements, however show several significant discrepancies with the theoretical predictions. The measurement techniques developed can also be used to investigate the noise of other semiconductor nanostructures such as quantum dots in the Kondo regime.\nA study of the noise characteristics alone can not determine whether the device is operating at the quantum limit; a characterization of back action is also necessary. The inelastic current through a double quantum dot system (DQD) is sensitive to the spectral density of voltage fluctuations in its electromagnetic environment. Electrical transport studies on a DQD system electrostatically coupled to an SET shows qualitative evidence of back-action of SET. The design and fabrication of a few electron DQD device with integrated RF-SET and QPC charge sensors for the study of back action of the sensors and real-time electron dynamics in the DQD are also discussed.
We have fabricated an aluminum single-electron transistor and characterized it at frequencies up to 10 MHz by measuring the reflected signal from a resonant tank in which the transistor is embedded. We measured the charge sensitivity of this radio-frequency single-electron transistor to be 3.2×10−6 e/Hz, which corresponds to the uncoupled energy sensitivity of 4.8 ℏ. Our measurements indicate that with further improvements, the radio-frequency single-electron transistor could reach the shot-noise limit estimated to be about 1 ℏ.
We present results on a double-island single-electron transistor (DISET) operated at radio frequency (rf) for the fast and highly sensitive detection of charge motion in the solid state. Using an intuitive definition for the charge sensitivity, we compare a DISET to a conventional single-electron transistor (SET). We find that a DISET can be more sensitive than a SET for identical, minimum device resistances in the Coulomb blockade regime. This is of particular importance for rf operation, where ideal impedance matching to 50-Ω transmission lines is only possible for a limited range of device resistances. We report a charge sensitivity of 5.6×10−6e∕Hz for a rf-DISET, together with a demonstration of the single-shot detection of small (⩽0.1e) charge signals on microsecond time scales.