Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

Microwave loss of DC sputtered NbTiN microstrip lines

Wenlei Shan, Yutaro Sekímoto, Takashi Noguchi

Published Aug 5, 2015• 5 citations
Publisher

Abstract

Abstract Amorphous NbTiN is widely applied in superconducting electronic devices owing to its merits of wide energy gap, high T c , and mitigated requirement in fabrication. Its highly disordered feature yields considerable kinetic inductance, making it an ideal material for parametric amplification. To build up the correspondence between the fabrication conditions and the desirable electrical performance, we designed, fabricated, and measured NbTiN microstrip resonators at microwave frequencies. The principal result is that the unloaded Q factor of the resonators does not depend on the film normal state resistivity, which largely depends on the sputtering pressure. This result is consistent with the dirty superconductor theories.

DOI
10.7567/jjap.54.090303

Related papers

High kinetic inductance NbTiN films for quantum limited travelling wave parametric amplifiers

Federica Mantegazzini, F Ahrens, M. Borghesi +13 more

Abstract A wide-bandwidth and low-noise amplification chain in the microwave regime is crucial for the efficient read-out of quantum systems based on superconducting detectors, such as Microwave Kinetic Inductance Detectors (MKIDs), Transition Edge Sensors (TESs), Magnetic Microcalorimeters (MMCs), and RF cavities, as well as qubits. Kinetic Inductance Travelling Wave Parametric Amplifiers (KI-TWPAs) operated in a three-wave mixing fashion have demonstrated exceptional dynamic range and low-noise performance, approaching the quantum limit. These amplifiers can be fabricated using a single layer of a high kinetic inductance film as weakly dispersive artificial transmission lines, with the ability to control the phase-matched bandwidth through dispersion engineering. In this study, we present the optimisation of the rf sputter-deposition process of NbTiN films using a Nb80%Ti20% target, with the goal of achieving precise control over film characteristics, resulting in high kinetic inductance while maintaining a high transition temperature. The parameter landscape related to the different sputtering conditions, such as pressure, power, and nitrogen flow, has been explored and the film thickness has been used as a fine-tuning parameter to adjust the properties of the final NbTiN films used for the fabrication of KI-TWPAs. As a final result, we have obtained a NbTiN film with a kinetic inductance of 8.5 pH/sq which we have exploited to fabricate KI-TWPA prototype devices, showing promising amplification performance.

arXiv:2310.11410•Physica Scripta•Oct 25, 2023•12 citations

Growth and Characterization of NbTiN Films Synthesized by Reactive Bias Target Ion Beam Deposition (RBTIBD)

Michael E. Cyberey, Tannaz Farrahi, Michael B. Eller +4 more

High energy gap Nb-based superconducting alloys with low normal state resistivity are fundamentally important for realization of low-loss high frequency circuits operating above the typical ~670 GHz gap frequency of elemental Nb. NbTiN has been shown to have a superconducting energy gap nearly twice that of elemental Nb, and is emerging as an important material for various detector and superconducting computing technologies. In this paper, we report on the growth of high-quality face-centered cubic (FCC) NbTiN films through the use of an alternative materials deposition technology-reactive bias target ion beam deposition. This novel technique offers more degrees of freedom compared to conventional sputtering, notably through decoupling the plasma generation and target bias, through use of a hollow-cathode ion source and independently pulse biased sputtering targets. The reported films are of high quality, with increased transition temperatures, reduced normal state resistivity, and surface roughness, compared to our previously reported reactive magnetron sputtered NbTiN films. In particular, at UVA, we are investigating these NbTiN films for wide-bandgap all-NbTiN superconducting-insulating-superconducting mixers, kinetic inductance detectors, and traveling-wave kinetic inductance parametric amplifier devices.

IEEE Transactions on Applied Superconductivity•Apr 27, 2019•5 citations

Fabrication and characterization of NbTi microwave superconducting resonators

Roberto Russo, André Chatel, Nergiz Şahin Solmaz +4 more

Superconducting resonators are widely used in fields spanning from quantum computing to electron spin resonance (ESR) spectroscopy. With the goal of realizing superconducting resonators, a broad variety and combination of superconducting materials, substrates and fabrication processes have been used and thoroughly reported in the literature. High temperature superconductors such as YBCO and low temperature superconductors such as Nb, NbN, NbTiN and Al are the major actors in the domain. In this work, we investigate the possibility to extend the family of suitable low temperature superconductors for the realization of planar superconducting microwave resonators for future ESR applications. In particular, this study focuses on NbTi, a widely used material to realize superconducting cables but not investigated for planar resonating structures at GHz frequencies. A 150 nm thick film of NbTi is sputtered and patterned on top of an Al2O3 substrate. For devices resonating around 6.8 GHz quality factors greater than 10,000 are observed at 3 K and in magnetic fields up to 250 mT.

Micro and Nano Engineering•May 10, 2023•9 citations

Fabrication and Characterization of Superconducting Resonators

Giuseppe Cataldo, Emily M. Barrentine, Ari-David Brown +3 more

Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.

Journal of Visualized Experiments•May 21, 2016•3 citations

Superconducting planar filter design

Martin Baránek, P. Neilinger, Daniel Manca +1 more

Superconducting planar resonators of thin molybdenum carbide (MoC) films were fabricated by optical lithography. The films were deposited via reactive magnetron sputtering and by changing the deposition parameters, the sheet resistance of the films was varied. The microwave properties of the resonators were studied by broadband coplanar waveguide spectroscopy in flip-chip configuration. The kinetic inductance of MoC films governs the high frequency response of the resonators and is determined by the complex conductivity of the superconducting film. Well below the critical temperature of transition, kinetic inductance is proportional to film sheet resistance in normal state. The temperature-dependent resonances in the broadband spectra below critical temperature are described by a lumped LC model, where the inductance consists of geometric and kinetic inductance of the resonator. The temperature and frequency dependent complex conductivity of the superconducting film is calculated by the Dynes model for dirty superconductors. Furthermore, a numerical model of the kinetic planar resonator in Sonnet software is presented, which can be utilized to design resonators with desired properties, based on highly disordered superconductors. An on-chip design of a kinetic planar resonator filter is presented. The high kinetic inductance of the superconducting films allows us to minimize microwave filter dimensions.

AIP conference proceedings•Jan 1, 2021•0 citations

Characterization of NbTiN Films for Superconducting Terahertz Circuitry

Yoshinori Uzawa, Kazumasa Makise, Shingo Saito +7 more

We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•1 citation
Abstract Amorphous NbTiN is widely applied in superconducting electronic devices owing to its merits of wide energy gap, high T c , and mitigated requirement in fabrication. Its highly disordered feature yields considerable kinetic inductance, making it an ideal material for parametric amplification. To build up the correspondence between the fabrication conditions and the desirable electrical performance, we designed, fabricated, and measured NbTiN microstrip resonators at microwave frequencies. The principal result is that the unloaded Q factor of the resonators does not depend on the film normal state resistivity, which largely depends on the sputtering pressure. This result is consistent with the dirty superconductor theories.
Abstract A wide-bandwidth and low-noise amplification chain in the microwave regime is crucial for the efficient read-out of quantum systems based on superconducting detectors, such as Microwave Kinetic Inductance Detectors (MKIDs), Transition Edge Sensors (TESs), Magnetic Microcalorimeters (MMCs), and RF cavities, as well as qubits. Kinetic Inductance Travelling Wave Parametric Amplifiers (KI-TWPAs) operated in a three-wave mixing fashion have demonstrated exceptional dynamic range and low-noise performance, approaching the quantum limit. These amplifiers can be fabricated using a single layer of a high kinetic inductance film as weakly dispersive artificial transmission lines, with the ability to control the phase-matched bandwidth through dispersion engineering. In this study, we present the optimisation of the rf sputter-deposition process of NbTiN films using a Nb80%Ti20% target, with the goal of achieving precise control over film characteristics, resulting in high kinetic inductance while maintaining a high transition temperature. The parameter landscape related to the different sputtering conditions, such as pressure, power, and nitrogen flow, has been explored and the film thickness has been used as a fine-tuning parameter to adjust the properties of the final NbTiN films used for the fabrication of KI-TWPAs. As a final result, we have obtained a NbTiN film with a kinetic inductance of 8.5 pH/sq which we have exploited to fabricate KI-TWPA prototype devices, showing promising amplification performance.
High energy gap Nb-based superconducting alloys with low normal state resistivity are fundamentally important for realization of low-loss high frequency circuits operating above the typical ~670 GHz gap frequency of elemental Nb. NbTiN has been shown to have a superconducting energy gap nearly twice that of elemental Nb, and is emerging as an important material for various detector and superconducting computing technologies. In this paper, we report on the growth of high-quality face-centered cubic (FCC) NbTiN films through the use of an alternative materials deposition technology-reactive bias target ion beam deposition. This novel technique offers more degrees of freedom compared to conventional sputtering, notably through decoupling the plasma generation and target bias, through use of a hollow-cathode ion source and independently pulse biased sputtering targets. The reported films are of high quality, with increased transition temperatures, reduced normal state resistivity, and surface roughness, compared to our previously reported reactive magnetron sputtered NbTiN films. In particular, at UVA, we are investigating these NbTiN films for wide-bandgap all-NbTiN superconducting-insulating-superconducting mixers, kinetic inductance detectors, and traveling-wave kinetic inductance parametric amplifier devices.
Superconducting resonators are widely used in fields spanning from quantum computing to electron spin resonance (ESR) spectroscopy. With the goal of realizing superconducting resonators, a broad variety and combination of superconducting materials, substrates and fabrication processes have been used and thoroughly reported in the literature. High temperature superconductors such as YBCO and low temperature superconductors such as Nb, NbN, NbTiN and Al are the major actors in the domain. In this work, we investigate the possibility to extend the family of suitable low temperature superconductors for the realization of planar superconducting microwave resonators for future ESR applications. In particular, this study focuses on NbTi, a widely used material to realize superconducting cables but not investigated for planar resonating structures at GHz frequencies. A 150 nm thick film of NbTi is sputtered and patterned on top of an Al2O3 substrate. For devices resonating around 6.8 GHz quality factors greater than 10,000 are observed at 3 K and in magnetic fields up to 250 mT.
Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.
Superconducting planar resonators of thin molybdenum carbide (MoC) films were fabricated by optical lithography. The films were deposited via reactive magnetron sputtering and by changing the deposition parameters, the sheet resistance of the films was varied. The microwave properties of the resonators were studied by broadband coplanar waveguide spectroscopy in flip-chip configuration. The kinetic inductance of MoC films governs the high frequency response of the resonators and is determined by the complex conductivity of the superconducting film. Well below the critical temperature of transition, kinetic inductance is proportional to film sheet resistance in normal state. The temperature-dependent resonances in the broadband spectra below critical temperature are described by a lumped LC model, where the inductance consists of geometric and kinetic inductance of the resonator. The temperature and frequency dependent complex conductivity of the superconducting film is calculated by the Dynes model for dirty superconductors. Furthermore, a numerical model of the kinetic planar resonator in Sonnet software is presented, which can be utilized to design resonators with desired properties, based on highly disordered superconductors. An on-chip design of a kinetic planar resonator filter is presented. The high kinetic inductance of the superconducting films allows us to minimize microwave filter dimensions.
We have investigated superconducting properties of niobium titanium nitride (NbTiN) films to be used for the lower and upper electrodes of a microstrip line with a SiO2insulator on a quartz substrate at Terahertz frequencies. NbTiN films were prepared on a 1-mm thick quartz substrate directly (assumed to be the lower electrode of the microstrip line) and on an about 150-nm thick SiO2layer sputtered on a quartz substrate (assumed to be the upper electrode) by reactive dc magnetron sputtering at ambient temperature. The complex conductivity measurement by Terahertz time- domain spectroscopy revealed that both films have similar superconducting properties with critical temperatures of about 14 K and gap frequencies of about 1.2 THz at 5 K. This indicates that all-NbTiN microstrip lines may work well as extremely low-loss transmission lines at Terahertz frequencies.