Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conversion gain and noise in a Josephson mixer. Technical report

Y. Taur, J. H. Claassen, P. L. Richards

Published Oct 1, 1973• 0 citations
OpenAlex

Abstract

Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 < or = eta < or = 4 and mixer noise temperatures in the neighborhood of ( Taub M) approximately 200K. The observed conversion efficiencies are in good agreement with the Resistively Shunted model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with omega sub (LO)/2 pi at 9GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.

Related papers

Conversion gain and noise in a Josephson mixer

Y. Taur, J. H. Claassen, P. L. Richards

Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 ≤ η ≤ 4 and mixer noise temperatures in the neighborhood of TM ~ 200 K. The observed conversion efficiencies are in good agreement with the Resistively Shunted Junction model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with ωLO/2 π at 9 GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.

Revue de Physique Appliquée•Jan 1, 1974•39 citations

Conversion gain in a Josephson effect mixer. Technical rept

Yuan Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb-Nb point contact Josephson-junctions used as 36 GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than one are attained, with mixer noise temperatures comparable with the best competing devices.

•Oct 1, 1973•0 citations

Conversion gain in a Josephson effect mixer

Y. Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb–Nb point contact Josephson junctions used as 36-GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than unity are attained, with mixer noise temperatures comparable with the best competing devices.

Applied Physics Letters•Jan 15, 1974•55 citations

Noise in Josepson effect mixers and the RSJ model

R. J. Schoelkopf, Tom G. Phillips, Jonas Stasys Zmuidzinas

Josephson effect mixers have previously been observed to display 'excess' noise both in experiments with point contacts and in numerical simulations using the resistively shunted junction (RSJ) model. This excess noise causes the mixer noise temperature to be a factor of typically 20-100 times the physical temperature of the device. Previously, this excess was ascribed to conversion from unwanted sidebands of the local oscillator and Josephson frequencies and their harmonics. Our numerical modeling of the RSJ equations has led to a new understanding of the excess noise, which is simply due to the intrinsic Josephson oscillations of the device. In addition, we have extended the modeling to include the previously ignored case of finite device capacitance (i.e. RSJ capacitance parameter beta(sub c) does not equal 0, which is more realistic for lithographically defined Josephson such as shunted tunnel junctions or SNS bridges. For some cases, this yields an improvement of a factor of two in noise temperature from the zero capacitance models. We will discuss the device parameters which optimize the mixer performance for frequencies approaching the characteristic frequency of the device, which is given by the Josephson frequency at the I(sub c)R(sub n) voltage (nu = 2eI(sub c)R(sub n)/h). These modeling results predict good conversion efficiency and a noise temperature within a factor of a few of the physical temperature. Experiments are in progress to determine the accuracy of this modeling using a waveguide mixer at 100 GHz with optimized, resistively shunted Nb tunnel junctions. If the modeling results are valid, they are particularly encouraging for mixers in the submillimeter regime, given the possibility of obtaining non-hysteretic Josephson devices with I(sub c)R(sub n) products in excess of a millivolt, using for instance, high-T(sub c) SNS bridges. We discuss the modifications to the classical RSJ model which are necessary in the quantum regime (h nu greater than kT), and conclude the Josephson mixers may attain noise temperatures less than ten times the quantum limit at high frequencies.

•Jan 1, 1992•0 citations

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations

Josephson frequency conversion in the range 145–1600 GHz with Nb–Nb superconducting point contacts used as oscillator-mixer

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.

Journal of Applied Physics•Jun 1, 1974•13 citations
Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 < or = eta < or = 4 and mixer noise temperatures in the neighborhood of ( Taub M) approximately 200K. The observed conversion efficiencies are in good agreement with the Resistively Shunted model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with omega sub (LO)/2 pi at 9GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.
Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 ≤ η ≤ 4 and mixer noise temperatures in the neighborhood of TM ~ 200 K. The observed conversion efficiencies are in good agreement with the Resistively Shunted Junction model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with ωLO/2 π at 9 GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.
Josephson effect mixers have previously been observed to display 'excess' noise both in experiments with point contacts and in numerical simulations using the resistively shunted junction (RSJ) model. This excess noise causes the mixer noise temperature to be a factor of typically 20-100 times the physical temperature of the device. Previously, this excess was ascribed to conversion from unwanted sidebands of the local oscillator and Josephson frequencies and their harmonics. Our numerical modeling of the RSJ equations has led to a new understanding of the excess noise, which is simply due to the intrinsic Josephson oscillations of the device. In addition, we have extended the modeling to include the previously ignored case of finite device capacitance (i.e. RSJ capacitance parameter beta(sub c) does not equal 0, which is more realistic for lithographically defined Josephson such as shunted tunnel junctions or SNS bridges. For some cases, this yields an improvement of a factor of two in noise temperature from the zero capacitance models. We will discuss the device parameters which optimize the mixer performance for frequencies approaching the characteristic frequency of the device, which is given by the Josephson frequency at the I(sub c)R(sub n) voltage (nu = 2eI(sub c)R(sub n)/h). These modeling results predict good conversion efficiency and a noise temperature within a factor of a few of the physical temperature. Experiments are in progress to determine the accuracy of this modeling using a waveguide mixer at 100 GHz with optimized, resistively shunted Nb tunnel junctions. If the modeling results are valid, they are particularly encouraging for mixers in the submillimeter regime, given the possibility of obtaining non-hysteretic Josephson devices with I(sub c)R(sub n) products in excess of a millivolt, using for instance, high-T(sub c) SNS bridges. We discuss the modifications to the classical RSJ model which are necessary in the quantum regime (h nu greater than kT), and conclude the Josephson mixers may attain noise temperatures less than ten times the quantum limit at high frequencies.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.