Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Studies of rubidium number density and polarization using spectrally-broadened diode lasers

E T Litaker

Published Jan 1, 2014• 0 citations
OpenAlex

Abstract

We have made systematic studies of rubidium (Rb) number density and polarization with the purpose of comparing a variety of techniques used to make these measurements. We have used five different temperatures, 40°C to 100°C in 15° increments, to compare number density measurements made using optical absorption with those made using Faraday rotation. A diode laser operating in the region near the Rb D1 transition was used in the case of the former, while for the latter two different lasers were used, one each operating in the vicinity of the Rb D1 and D2 transitions. These number density results are compared with those obtained from vapor temperature formulae (e.g., Killian, CRC, etc.). We have also made a systematic study of Rb optical pumping using an amplified tunable diode laser which has been incrementally broadened in order to determine the effect of linewidth broadening on Rb polarization. We vary the frequency of the circularly-polarized pump laser across the D1 transition absorption profile for each of four linewidths (0.01, 0.5, 2, and 8 GHz) and measure the Rb polarization using Faraday rotation. The Rb number density for these measurements is on the order of 1012 cm−3, with 1 Torr of N2 as the buffer gas. These results are then compared with polarization measurements taken using a re-pump laser operating near the Rb D2 transition, and with theoretical calculations of the rubidium polarization.

Related papers

An Interferometric Technique Of Density Measurement Applied To Alkali-metal Vapors Oriented By Optical Pumping.

Steven Jarrett

III-8.Comparison of optical pumping signals for two spherical cells with different buffer gas pressures as a function of density times diameter of cell for equal D2/D1.60 IV-1.Energy level diagram showing hyperfine structure of Rb Di line.Units are 10*3 cm-1.67 IV-2.Equivalent circuit for rate equations involving ex change polarization.73 IV-3.Diagram of optical system for optical pumping of Rb. 83 IV-4.Block diagram of Rb optical pumping signal detection system.85 IV-5.Block diagram of Rb light detection system.90 IV-6.Typical photograph from which relaxation time measure ments are made..Time increases from left to right.Scale is 1 millisecond per division.92 IV-7.Lines determined from measurements on time dependence of Rb87 signals at 50°C for the two different light in tensities.Scatter of points is too small to be notice able on graph.93 A-1.Spectral profile of D1 radiation from a Varian spectral lamp containing natural Rb.Ill A-2.Spectral profile of Di radiation from a Varian spectral lamp containing Rb87.112 A-3-Spectral profile of Di radiation from a Varian spectral lamp containing Rb87 after filtering by an Rb85 absorption cell.113 vi CHAPTER I2 atomic ground states and the parameters of various relaxation processes of gaseous systems.These investigations led to the development of mag netometers of unique sensitivity.More recently, very precise frequency standards have been developed using the methods of optical pumping and the knowledge gained through their application.The present work was undertaken in the context of extending our knowledge of the dynamics of optical pumping methods and of exploiting these methods for the deter mination of an interesting atomic exchange cross section.Optical pumping may be considered as a specialized technique used in conjunction with magnetic resonance phenomena.All magnetic reso nance techniques depend upon obtaining an oriented (polarized) macro scopic sample of matter, that is, matter with a net magnetic moment.In the atomic beam magnetic resonance method, this is accomplished by sort ing out, spatially, atoms whose magnetic moments have a particular ori entation with respect to a magnetic field.In nuclear or electron para magnetic resonance work in solids, liquids, or gases, the small thermal equilibrium polarization that matter possesses in a magnetic field is exploited.Optical pumping enhances this equilibrium polarization through selective optical absorption, by a gaseous atomic system, of polarized resonance radiation.Optical pumping offers the great advan tage of experimental simplicity, as compared to other magnetic resonance techniques, but suffers from severe limitations in application.Since the original suggestion by Brossel and Nastier^ and subse quent development by many others, optical pumping, in conjunction with the transmission monitoring technique of signal detection, has became a standard technique in the study of alkali metal ground states.By far the greatest amount of work in optical pumping has been concerned with alkali metal vapors.Bell, Bloom/ and others^ have considered the process of the optical pumping of the alkalis with attention to the spec tral composition of the pumping light, that is, the resonance radiation incident on the alkali vapor.Colegrove and Franken? have recently dis cussed the complication in the analyses of optical pumping signals for Q helium when the helium absorption cell is optically thick.Hobart has considered this same complication for sodium.Prediction of signals must take into account the fact that the pumping light is absorbed ap proximately exponentially in the optical pumping absorption cell.This means that the absorption coefficient, which is proportional to the al kali density, times the length of the cell is a significant parameter in determining the strength of the signal.Similar calculations of the dependence of optical pumping signals on alkali density and spectral com position of the pumping light will be presented in this work.In order to test the signal predictions> a high resolution Fabry-Perot spectrometer was constructed.This instrument can be used for two purposes : the investigation of the intensity distribution of the pumping light, and, more importantly, determinations of the alkali vapor density in the absorption cell.The desired data are curves of optical pumping signals, for a typical sodium optical pumping experiment, as a function of density.It is often necessary to know these densities in order to is limited to the accuracy to which the density is known.Since the Fabry-Perot spectrometer used to measure sodium vapor densities in conjunction with the signal strength versus density meas urements can be applied to different systems, it was decided to make a determination of the rubidium 85-rubidium 87 spin exchange cross sec tion.The reasons for this choice are discussed in detail in Chapt.IV.In brief, work on rubidium exchange offered some experimental sim plifications and rubidium has previously been studied more thoroughly than other systems.

•Jan 1, 1963•0 citations

Straightforward Measurement of Saturation Intensity of Doppler-Broadened Transitions: Application to Rubidium Vapour

Omid Mozafar, Varun Sharma, R. Margoth Córdova‐Castro +3 more

The commonly quoted saturation intensity of rubidium (Rb) for D2 transitions is 16.7$\mathrm{W}.\mathrm{m}^{-2}$. This value, however, is only accurate for the cycling transition, which renders the Rb atom to resemble a two-level system. In practice, the effective saturation intensity is influenced by various factors, such as the polarization of light, optical pumping, and atom collision which can redistribute the population. As a result, it is crucial to experimentally determine the effective saturation intensity. In this context, we demonstrate a novel yet simple experimental method to measure the effective saturation intensities of Doppler-broadened transitions in atomic vapours. Our method only requires on-resonance absorbance data for various input laser intensities, which can be obtained with a tunable CW laser without the need for precise frequency locking. We applied this method to measure the effective saturation intensities of all four Doppler-broadened D2 transitions in natural rubidium (Rb) vapour (27.8%87Rb and 72.2 %${}^{\text{8}} {}^{\text{5}}Rb$) at$r={35}^{\circ} \mathrm{C}$. The results show that the effective saturation intensities for Rb range from 0.752 to 16.8$\mathrm{W}.\mathrm{m}^{-2}$. Notably, for certain transitions (specifically, repump transitions), the effective saturation intensities were smaller than 16.7 W.$\mathrm{m}^{-2}$(up to an order of magnitude), with potentially important implications for optical pumping in Doppler-broadened transitions.

Photonics North (PN)•May 28, 2024•0 citations

Polarization rotation spectral profiles for the D2 line of 87 Rb atoms: theory and experiment

Geol Moon, Seung-Chul Yang, Jin‐Tae Kim +1 more

Abstract We present a theoretical and experimental study of the polarization rotation of a linearly polarized probe beam scanning across all of the neighboring hyperfine levels ( F e = 1 and 2) with a circularly polarized pumping beam resonant on the F g = 2 → F e = 3 transition of the D2 line of 87 Rb atoms. The experimental results match well with the results calculated from the full-level density matrix equations considering laser phase noise, which hinders observations of narrow lines with linewidths of ∼90 kHz, as calculated in polarization rotation spectra for the first time.

Journal of Physics B Atomic Molecular and Optical Physics•Sep 23, 2019•4 citations

Radiation trapping in rubidium optical pumping at low buffer-gas pressures

Mark Rosenberry, J. Paxon Reyes, D. Tupa +1 more

We have made a systematic study of rubidium optical pumping in a simple cylindrical cell geometry with a high-power $10\phantom{\rule{0.3em}{0ex}}\mathrm{W}$ diode laser array, low magnetic fields, and buffer-gas pressures of less than $50\phantom{\rule{0.3em}{0ex}}\text{torr}$. We have determined rubidium polarizations experimentally for ${\mathrm{H}}_{2}$, ${\mathrm{N}}_{2}$, He, and Ar buffer gases, with Rb number densities from ${10}^{12}\phantom{\rule{0.3em}{0ex}}\text{to}\phantom{\rule{0.3em}{0ex}}{10}^{13}\phantom{\rule{0.3em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}3}$. Comparison to a relatively simple optical pumping model allows us to extract useful information about radiation trapping and quenching effects.

Physical Review A•Feb 1, 2007•71 citations

Measurement of Rubidium Number Density Under Optically Thick Conditions

Matthew D. Rotondaro, Charles F. Wisniewski, Martiqua L. Post +1 more

A measurement of rubidium number density under optically thick conditions has been demonstrated by measuring the wings of the D1 absorption spectra using a laser with a 0.16 nm (75 GHz) fine tuning range. This technique can measure the absolute concentration in rubidium under conditions where the absorption coefficient and path length product yield conditions where the central region of the line is opaque. The laser was tuned to a region sufficiently far into the short wavelength wing of the absorption where transmission through the cell was possible. The laser was then scanned through the central opaque region of the line to the adjacent long wavelength wing. The wavelength of the scan was calibrated by using a 1.5 GHz etalon and a cell containing only naturally occurring rubidium as a frequency reference. The measured absorption spectra for various cell conditions of temperature and pressure were then fit to a pressure broadened Voigt profile thereby allowing the determination of the rubidium number density.

AIAA Plasmadynamics and Lasers Conference•Jun 28, 2010•3 citations

Temperature dependence of Doppler-broadening in rubidium: An undergraduate experiment

Chris Leahy, J. Todd Hastings, P. M. Wilt

This paper describes experiments performed by undergraduate physics majors to measure the temperature dependence of Doppler-broadening in Rb absorption lines over the interval 290–500 K. We report measurements made with a laser-diode spectrometer on the resolved hyperfine transitions of Rb87 (5 2S1/2 F=1 to 5 2P1/2, F=1 and 2) near 795 nm, and on the unresolved envelope of the transitions of Rb85 (5 2S1/2 F=2 to 5 2P3/2, F=1, 2 and 3) near 780 nm. Agreement between measured and predicted linewidths is very good.

American Journal of Physics•May 1, 1997•19 citations
We have made systematic studies of rubidium (Rb) number density and polarization with the purpose of comparing a variety of techniques used to make these measurements. We have used five different temperatures, 40°C to 100°C in 15° increments, to compare number density measurements made using optical absorption with those made using Faraday rotation. A diode laser operating in the region near the Rb D1 transition was used in the case of the former, while for the latter two different lasers were used, one each operating in the vicinity of the Rb D1 and D2 transitions. These number density results are compared with those obtained from vapor temperature formulae (e.g., Killian, CRC, etc.). We have also made a systematic study of Rb optical pumping using an amplified tunable diode laser which has been incrementally broadened in order to determine the effect of linewidth broadening on Rb polarization. We vary the frequency of the circularly-polarized pump laser across the D1 transition absorption profile for each of four linewidths (0.01, 0.5, 2, and 8 GHz) and measure the Rb polarization using Faraday rotation. The Rb number density for these measurements is on the order of 1012 cm−3, with 1 Torr of N2 as the buffer gas. These results are then compared with polarization measurements taken using a re-pump laser operating near the Rb D2 transition, and with theoretical calculations of the rubidium polarization.
III-8.Comparison of optical pumping signals for two spherical cells with different buffer gas pressures as a function of density times diameter of cell for equal D2/D1.60 IV-1.Energy level diagram showing hyperfine structure of Rb Di line.Units are 10*3 cm-1.67 IV-2.Equivalent circuit for rate equations involving ex change polarization.73 IV-3.Diagram of optical system for optical pumping of Rb. 83 IV-4.Block diagram of Rb optical pumping signal detection system.85 IV-5.Block diagram of Rb light detection system.90 IV-6.Typical photograph from which relaxation time measure ments are made..Time increases from left to right.Scale is 1 millisecond per division.92 IV-7.Lines determined from measurements on time dependence of Rb87 signals at 50°C for the two different light in tensities.Scatter of points is too small to be notice able on graph.93 A-1.Spectral profile of D1 radiation from a Varian spectral lamp containing natural Rb.Ill A-2.Spectral profile of Di radiation from a Varian spectral lamp containing Rb87.112 A-3-Spectral profile of Di radiation from a Varian spectral lamp containing Rb87 after filtering by an Rb85 absorption cell.113 vi CHAPTER I2 atomic ground states and the parameters of various relaxation processes of gaseous systems.These investigations led to the development of mag netometers of unique sensitivity.More recently, very precise frequency standards have been developed using the methods of optical pumping and the knowledge gained through their application.The present work was undertaken in the context of extending our knowledge of the dynamics of optical pumping methods and of exploiting these methods for the deter mination of an interesting atomic exchange cross section.Optical pumping may be considered as a specialized technique used in conjunction with magnetic resonance phenomena.All magnetic reso nance techniques depend upon obtaining an oriented (polarized) macro scopic sample of matter, that is, matter with a net magnetic moment.In the atomic beam magnetic resonance method, this is accomplished by sort ing out, spatially, atoms whose magnetic moments have a particular ori entation with respect to a magnetic field.In nuclear or electron para magnetic resonance work in solids, liquids, or gases, the small thermal equilibrium polarization that matter possesses in a magnetic field is exploited.Optical pumping enhances this equilibrium polarization through selective optical absorption, by a gaseous atomic system, of polarized resonance radiation.Optical pumping offers the great advan tage of experimental simplicity, as compared to other magnetic resonance techniques, but suffers from severe limitations in application.Since the original suggestion by Brossel and Nastier^ and subse quent development by many others, optical pumping, in conjunction with the transmission monitoring technique of signal detection, has became a standard technique in the study of alkali metal ground states.By far the greatest amount of work in optical pumping has been concerned with alkali metal vapors.Bell, Bloom/ and others^ have considered the process of the optical pumping of the alkalis with attention to the spec tral composition of the pumping light, that is, the resonance radiation incident on the alkali vapor.Colegrove and Franken? have recently dis cussed the complication in the analyses of optical pumping signals for Q helium when the helium absorption cell is optically thick.Hobart has considered this same complication for sodium.Prediction of signals must take into account the fact that the pumping light is absorbed ap proximately exponentially in the optical pumping absorption cell.This means that the absorption coefficient, which is proportional to the al kali density, times the length of the cell is a significant parameter in determining the strength of the signal.Similar calculations of the dependence of optical pumping signals on alkali density and spectral com position of the pumping light will be presented in this work.In order to test the signal predictions> a high resolution Fabry-Perot spectrometer was constructed.This instrument can be used for two purposes : the investigation of the intensity distribution of the pumping light, and, more importantly, determinations of the alkali vapor density in the absorption cell.The desired data are curves of optical pumping signals, for a typical sodium optical pumping experiment, as a function of density.It is often necessary to know these densities in order to is limited to the accuracy to which the density is known.Since the Fabry-Perot spectrometer used to measure sodium vapor densities in conjunction with the signal strength versus density meas urements can be applied to different systems, it was decided to make a determination of the rubidium 85-rubidium 87 spin exchange cross sec tion.The reasons for this choice are discussed in detail in Chapt.IV.In brief, work on rubidium exchange offered some experimental sim plifications and rubidium has previously been studied more thoroughly than other systems.
The commonly quoted saturation intensity of rubidium (Rb) for D2 transitions is 16.7W.m−2\mathrm{W}.\mathrm{m}^{-2}W.m−2. This value, however, is only accurate for the cycling transition, which renders the Rb atom to resemble a two-level system. In practice, the effective saturation intensity is influenced by various factors, such as the polarization of light, optical pumping, and atom collision which can redistribute the population. As a result, it is crucial to experimentally determine the effective saturation intensity. In this context, we demonstrate a novel yet simple experimental method to measure the effective saturation intensities of Doppler-broadened transitions in atomic vapours. Our method only requires on-resonance absorbance data for various input laser intensities, which can be obtained with a tunable CW laser without the need for precise frequency locking. We applied this method to measure the effective saturation intensities of all four Doppler-broadened D2 transitions in natural rubidium (Rb) vapour (27.8%87Rb and 72.2 %85Rb{}^{\text{8}} {}^{\text{5}}Rb85Rb) atr=35∘Cr={35}^{\circ} \mathrm{C}r=35∘C. The results show that the effective saturation intensities for Rb range from 0.752 to 16.8W.m−2\mathrm{W}.\mathrm{m}^{-2}W.m−2. Notably, for certain transitions (specifically, repump transitions), the effective saturation intensities were smaller than 16.7 W.m−2\mathrm{m}^{-2}m−2(up to an order of magnitude), with potentially important implications for optical pumping in Doppler-broadened transitions.
Abstract We present a theoretical and experimental study of the polarization rotation of a linearly polarized probe beam scanning across all of the neighboring hyperfine levels ( F e = 1 and 2) with a circularly polarized pumping beam resonant on the F g = 2 → F e = 3 transition of the D2 line of 87 Rb atoms. The experimental results match well with the results calculated from the full-level density matrix equations considering laser phase noise, which hinders observations of narrow lines with linewidths of ∼90 kHz, as calculated in polarization rotation spectra for the first time.
We have made a systematic study of rubidium optical pumping in a simple cylindrical cell geometry with a high-power 10W10\phantom{\rule{0.3em}{0ex}}\mathrm{W}10W diode laser array, low magnetic fields, and buffer-gas pressures of less than 50torr50\phantom{\rule{0.3em}{0ex}}\text{torr}50torr. We have determined rubidium polarizations experimentally for H2{\mathrm{H}}_{2}H2​, N2{\mathrm{N}}_{2}N2​, He, and Ar buffer gases, with Rb number densities from ${10}^{12}\phantom{\rule{0.3em}{0ex}}\text{to}\phantom{\rule{0.3em}{0ex}}{10}^{13}\phantom{\rule{0.3em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}3}$. Comparison to a relatively simple optical pumping model allows us to extract useful information about radiation trapping and quenching effects.
A measurement of rubidium number density under optically thick conditions has been demonstrated by measuring the wings of the D1 absorption spectra using a laser with a 0.16 nm (75 GHz) fine tuning range. This technique can measure the absolute concentration in rubidium under conditions where the absorption coefficient and path length product yield conditions where the central region of the line is opaque. The laser was tuned to a region sufficiently far into the short wavelength wing of the absorption where transmission through the cell was possible. The laser was then scanned through the central opaque region of the line to the adjacent long wavelength wing. The wavelength of the scan was calibrated by using a 1.5 GHz etalon and a cell containing only naturally occurring rubidium as a frequency reference. The measured absorption spectra for various cell conditions of temperature and pressure were then fit to a pressure broadened Voigt profile thereby allowing the determination of the rubidium number density.
This paper describes experiments performed by undergraduate physics majors to measure the temperature dependence of Doppler-broadening in Rb absorption lines over the interval 290–500 K. We report measurements made with a laser-diode spectrometer on the resolved hyperfine transitions of Rb87 (5 2S1/2 F=1 to 5 2P1/2, F=1 and 2) near 795 nm, and on the unresolved envelope of the transitions of Rb85 (5 2S1/2 F=2 to 5 2P3/2, F=1, 2 and 3) near 780 nm. Agreement between measured and predicted linewidths is very good.