Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2611.00424

Effect of Rapid Thermal Annealing on the Superconductivity of ALD-Grown TiN thin films

Z. Sadirkhanov, A. Tuigynbek, M. Surendran, A. Jakyp, L. Akisheva, A. T. Hammack, A. B. Tikhonov, A. Kemelbay

Published Oct 30, 2026• 0 citations
arXivHTMLPDF

Abstract

Titanium nitride (TiN) is a promising superconducting material for scalable quantum technologies owing to its tunable kinetic inductance and compatibility with CMOS thin-film processing. However, the superconducting performance of atomic-layer-deposited TiN can be degraded by oxygen incorporation, off-stoichiometry, and crystallographic disorder. In this work, we investigate rapid thermal annealing (RTA) in high-purity nitrogen as a post-deposition strategy to improve polycrystalline TiN films grown by RF-biased plasma-enhanced atomic layer deposition. Grazing-incidence X-ray diffraction reveals reduced peak broadening, a smaller lattice parameter, and a stronger (111) preferred orientation with increasing annealing temperature. X-ray photoelectron spectroscopy depth profiling shows reduced oxygen-related bonding and a shift toward a Ti--N-dominated chemical environment after annealing. These structural and chemical changes result in a 25% increase in the superconducting transition temperature and a significant narrowing of the transition width. Annealing also reduced the sheet resistance and the estimated sheet kinetic inductance, increased the residual resistance ratio, and improved the magnetic-field tolerance. Together, the structural, chemical, and transport results are consistent with reduced material disorder and improved superconducting uniformity. Because RTA is a relatively low thermal budget and is a semiconductor fabrication compatible process, it offers a practical route to improve the quality of ALD-grown TiN for superconducting applications.

DOI
10.48550/arxiv.2611.00424

Related papers

Superconducting titanium nitride films grown by directional reactive evaporation

Raymond Mencia, Yen‐Hsiang Lin, Vladimir Manucharyan

We report a novel method of growing strongly disordered superconducting titanium nitride (TiN) thin films by reactive electron-beam deposition. The normal state sheet resistance and superconducting critical temperature (Tc) can be tuned by controlling the deposition pressure in the range of 1.1×10−6–3.1×10−5mbar. For 10nm thick films, the sheet resistance (R□) reaches 1361Ω/□ and Tc=0.77K, which translates into an estimate for the sheet inductance as large as L□=2.4nH/□. Benefiting from the directionality of reactive evaporation, we fabricated RF test devices with micrometer-sized dimensions using a resist mask and a lift-off process, which would be difficult with sputtering or atomic layer deposition methods. The spectroscopic measurements result in consistent sheet inductance values in two different device geometries, and the quality factors ranged from Q = 300 to 2200. The loss is possibly due to the presence of titanium oxynitride (TiNxOy) in the morphological composition of our films. The flexibility of the lift-off process suggests applications of reactively evaporated TiN for making supporting structures around quantum circuits, such as readout resonators or compact on-chip filters.

arXiv:2011.09446•Journal of Applied Physics•Dec 13, 2021•5 citations

Low-loss superconducting titanium nitride grown using plasma-assisted molecular beam epitaxy

Christopher J. K. Richardson, Ashish Alexander, Christopher Weddle +2 more

Titanium nitride (TiN) is a known superconducting material that is attractive for use as passive components in superconducting circuits for both conventional and quantum information devices. In contrast to conventional synthesis techniques, here, plasma-assisted molecular beam epitaxy is reported to produce high-quality TiN on bare silicon wafers. Using a rf-plasma source to crack the nitrogen molecules and a conventional high-temperature effusion cell for titanium, TiN growth is completed under nitrogen-rich conditions. The growth and nucleation is monitored in situ, while the structure and composition are characterized using x-ray diffraction, atomic force microscopy, x-ray photoelectron spectroscopy, secondary ion mass spectroscopy, and scanning transmission electron microscopy. The stoichiometric TiN (111) films sit on an amorphous nitride layer with low impurity concentrations. The films superconduct with Tc=5.4 K, and coplanar waveguide resonators are fabricated with a small center width of 6 μm that demonstrate single-photon quality factors approaching 1M and high-power quality factors over 5M without observing saturation.

Journal of Applied Physics•Jun 18, 2020•41 citations

Growth of titanium-nitride thin films for low-loss superconducting quantum circuits

Gustaf Olson

This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.

•May 29, 2015•3 citations

Optimizing CMOS-compatible, superconducting titanium nitride resonators: Deposition conditions and structuring processes

Simon J. K. Lang, Alexandra Schewski, Ignaz Eisele +10 more

We report on the fabrication and characterization of superconducting coplanar waveguide (CPW) resonators based on titanium nitride (TiN) thin films deposited on 200\,mm diameter high-resistivity Si(100) substrates. We systematically investigate how deposition conditions, dry-etch power and in-situ resist strip temperature affect morphology, superconducting properties and dielectric losses. By tuning reactive sputtering conditions, three distinct preferred out-of-plane crystal orientations - (111), (200), and a mix of both are achieved. Our results demonstrate that all films exhibit similar minimal two-level system (TLS) losses, with TiN111 exhibiting the lowest median TLS losses $\tildeδ_\mathrm{TLS}$, and greater robustness against reoxidation. The applied structuring process, in contrast, has a far greater influence on the TLS loss than the crystal orientation of the TiN film and, consequently, the intrinsic material properties of the superconducting layer. The lowest TLS losses for all TiN depositions were achieved with a low power etch and low temperature resist strip. An additional buffered oxide etch (BOE) treatment could remove high-loss interfacial oxides at the metal-air (MA) and substrate-air (SA) interface and recover the etch-induced TLS losses. Consequently, TiN resonators exhibiting $\tildeδ_\mathrm{TLS}$ values as low as $9.67 \times 10^{-7}$ were realized. The corresponding median low-power loss, $\tildeδ_\mathrm{LP}$, amounts to $11.04 \times 10^{-7}$, which translates to an internal quality factor approaching one million. These findings highlight the critical role of process induced oxide formation at the MA and SA interfaces in limiting the performance of TiN resonators and provide a scalable, low-loss process compatible with industry-grade 200\,mm CMOS qubit fabrication workflows.

quant-pharXiv:2603.00441•Applied Physics Reviews•Mar 3, 2026•2 citations

Design and Characterisation of Titanium Nitride Subarrays of Kinetic Inductance Detectors for Passive Terahertz Imaging

D. Morozov, Simon M. Doyle, Archan Banerjee +5 more

We report on the investigation of titanium nitride (TiN) thin films deposited via atomic layer deposition (ALD) for microwave kinetic inductance detectors (MKID). Using our in-house ALD process, we have grown a sequence of TiN thin films (thickness 15, 30, 60 nm). The films have been characterised in terms of superconducting transition temperature $$T_\mathrm{c}$$ , sheet resistance $$R_\mathrm{s}$$ and microstructure. We have fabricated test resonator structures and characterised them at a temperature of 300 mK. At 350 GHz, we report an optical noise equivalent power $$\hbox {NEP}_\mathrm{opt} \approx 2.3\times 10^{-15}~\hbox {W}/\sqrt{\hbox {Hz}}$$ , which is promising for passive terahertz imaging applications.

Journal of Low Temperature Physics•Jul 18, 2018•9 citations

Effect of Post Deposition Annealing on the Structural and Electrical Properties of NbTiN Thin Films Deposited by Reactive Bias Target Ion Beam Deposition Technique

Tannaz Farrahi, Michael E. Cyberey, Michael B. Eller +1 more

Nb-based superconducting alloys, such as NbN and NbTiN, can have a superconducting energy gap near twice that of elemental Nb, thus, being ideal candidates for low-loss superconducting circuits operating above the gap frequency of Nb. We are particularly interested in these materials for THz-frequency superconducting-insulating-superconducting (SIS) mixers, kinetic inductance detectors, and traveling wave kinetic inductance parametric amplifier devices. We recently reported the use of an alternative synthesis technique, reactive bias target ion beam deposition (RBTIBD), used to realize high-quality NbTiN films and high-energy gap NbTiN/AlN/NbTiN SIS heterostructures. In this paper, the effect of post-deposition annealing on the electrical and structural properties of room temperature deposited RBTIBD NbTiN was investigated. Our room temperature RBTIBD NbTiN films were annealed using rapid thermal annealing from 200 to 1000 °C. The change in structural and electrical properties was characterized by X-ray diffraction, atomic force microscopy, and four-point probe measurements. The annealed films demonstrated an enhancement in transition temperature (Tc), increased crystallinity, larger grain size, and significantly reduced intrinsic stress.

IEEE Transactions on Applied Superconductivity•May 9, 2019•9 citations
Titanium nitride (TiN) is a promising superconducting material for scalable quantum technologies owing to its tunable kinetic inductance and compatibility with CMOS thin-film processing. However, the superconducting performance of atomic-layer-deposited TiN can be degraded by oxygen incorporation, off-stoichiometry, and crystallographic disorder. In this work, we investigate rapid thermal annealing (RTA) in high-purity nitrogen as a post-deposition strategy to improve polycrystalline TiN films grown by RF-biased plasma-enhanced atomic layer deposition. Grazing-incidence X-ray diffraction reveals reduced peak broadening, a smaller lattice parameter, and a stronger (111) preferred orientation with increasing annealing temperature. X-ray photoelectron spectroscopy depth profiling shows reduced oxygen-related bonding and a shift toward a Ti--N-dominated chemical environment after annealing. These structural and chemical changes result in a 25% increase in the superconducting transition temperature and a significant narrowing of the transition width. Annealing also reduced the sheet resistance and the estimated sheet kinetic inductance, increased the residual resistance ratio, and improved the magnetic-field tolerance. Together, the structural, chemical, and transport results are consistent with reduced material disorder and improved superconducting uniformity. Because RTA is a relatively low thermal budget and is a semiconductor fabrication compatible process, it offers a practical route to improve the quality of ALD-grown TiN for superconducting applications.
We report a novel method of growing strongly disordered superconducting titanium nitride (TiN) thin films by reactive electron-beam deposition. The normal state sheet resistance and superconducting critical temperature (Tc) can be tuned by controlling the deposition pressure in the range of 1.1×10−6–3.1×10−5mbar. For 10nm thick films, the sheet resistance (R□) reaches 1361Ω/□ and Tc=0.77K, which translates into an estimate for the sheet inductance as large as L□=2.4nH/□. Benefiting from the directionality of reactive evaporation, we fabricated RF test devices with micrometer-sized dimensions using a resist mask and a lift-off process, which would be difficult with sputtering or atomic layer deposition methods. The spectroscopic measurements result in consistent sheet inductance values in two different device geometries, and the quality factors ranged from Q = 300 to 2200. The loss is possibly due to the presence of titanium oxynitride (TiNxOy) in the morphological composition of our films. The flexibility of the lift-off process suggests applications of reactively evaporated TiN for making supporting structures around quantum circuits, such as readout resonators or compact on-chip filters.
Titanium nitride (TiN) is a known superconducting material that is attractive for use as passive components in superconducting circuits for both conventional and quantum information devices. In contrast to conventional synthesis techniques, here, plasma-assisted molecular beam epitaxy is reported to produce high-quality TiN on bare silicon wafers. Using a rf-plasma source to crack the nitrogen molecules and a conventional high-temperature effusion cell for titanium, TiN growth is completed under nitrogen-rich conditions. The growth and nucleation is monitored in situ, while the structure and composition are characterized using x-ray diffraction, atomic force microscopy, x-ray photoelectron spectroscopy, secondary ion mass spectroscopy, and scanning transmission electron microscopy. The stoichiometric TiN (111) films sit on an amorphous nitride layer with low impurity concentrations. The films superconduct with Tc=5.4 K, and coplanar waveguide resonators are fabricated with a small center width of 6 μm that demonstrate single-photon quality factors approaching 1M and high-power quality factors over 5M without observing saturation.
This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.
We report on the fabrication and characterization of superconducting coplanar waveguide (CPW) resonators based on titanium nitride (TiN) thin films deposited on 200\,mm diameter high-resistivity Si(100) substrates. We systematically investigate how deposition conditions, dry-etch power and in-situ resist strip temperature affect morphology, superconducting properties and dielectric losses. By tuning reactive sputtering conditions, three distinct preferred out-of-plane crystal orientations - (111), (200), and a mix of both are achieved. Our results demonstrate that all films exhibit similar minimal two-level system (TLS) losses, with TiN111 exhibiting the lowest median TLS losses δ~TLS\tildeδ_\mathrm{TLS}δ~TLS​, and greater robustness against reoxidation. The applied structuring process, in contrast, has a far greater influence on the TLS loss than the crystal orientation of the TiN film and, consequently, the intrinsic material properties of the superconducting layer. The lowest TLS losses for all TiN depositions were achieved with a low power etch and low temperature resist strip. An additional buffered oxide etch (BOE) treatment could remove high-loss interfacial oxides at the metal-air (MA) and substrate-air (SA) interface and recover the etch-induced TLS losses. Consequently, TiN resonators exhibiting δ~TLS\tildeδ_\mathrm{TLS}δ~TLS​ values as low as 9.67×10−79.67 \times 10^{-7}9.67×10−7 were realized. The corresponding median low-power loss, δ~LP\tildeδ_\mathrm{LP}δ~LP​, amounts to 11.04×10−711.04 \times 10^{-7}11.04×10−7, which translates to an internal quality factor approaching one million. These findings highlight the critical role of process induced oxide formation at the MA and SA interfaces in limiting the performance of TiN resonators and provide a scalable, low-loss process compatible with industry-grade 200\,mm CMOS qubit fabrication workflows.
We report on the investigation of titanium nitride (TiN) thin films deposited via atomic layer deposition (ALD) for microwave kinetic inductance detectors (MKID). Using our in-house ALD process, we have grown a sequence of TiN thin films (thickness 15, 30, 60 nm). The films have been characterised in terms of superconducting transition temperature TcT_\mathrm{c}Tc​ , sheet resistance RsR_\mathrm{s}Rs​ and microstructure. We have fabricated test resonator structures and characterised them at a temperature of 300 mK. At 350 GHz, we report an optical noise equivalent power NEPopt≈2.3×10−15 W/Hz\hbox {NEP}_\mathrm{opt} \approx 2.3\times 10^{-15}~\hbox {W}/\sqrt{\hbox {Hz}}NEPopt​≈2.3×10−15 W/Hz​ , which is promising for passive terahertz imaging applications.
Nb-based superconducting alloys, such as NbN and NbTiN, can have a superconducting energy gap near twice that of elemental Nb, thus, being ideal candidates for low-loss superconducting circuits operating above the gap frequency of Nb. We are particularly interested in these materials for THz-frequency superconducting-insulating-superconducting (SIS) mixers, kinetic inductance detectors, and traveling wave kinetic inductance parametric amplifier devices. We recently reported the use of an alternative synthesis technique, reactive bias target ion beam deposition (RBTIBD), used to realize high-quality NbTiN films and high-energy gap NbTiN/AlN/NbTiN SIS heterostructures. In this paper, the effect of post-deposition annealing on the electrical and structural properties of room temperature deposited RBTIBD NbTiN was investigated. Our room temperature RBTIBD NbTiN films were annealed using rapid thermal annealing from 200 to 1000 °C. The change in structural and electrical properties was characterized by X-ray diffraction, atomic force microscopy, and four-point probe measurements. The annealed films demonstrated an enhancement in transition temperature (Tc), increased crystallinity, larger grain size, and significantly reduced intrinsic stress.