arXiv:2610.21435
Accurate gap control of 3D-integrated superconducting quantum circuits using asymmetric indium architecture and multi-angle flip-chip bonding
L. Richard, N. Bruckmoser, J. Feigl, D. Bunch, A. Bhattacharjee, L. Koch, I. Tsitsilin, V. P. Bader, H. Hu, L. Södergren, S. Filipp
Abstract
Flip-chip 3D integration is a key enabling technology for overcoming the routing and layout constraints of planar superconducting quantum processors, but it requires accurate and uniform control of the inter-chip spacing while preserving qubit coherence. In conventional processes, thick indium bumps are deposited symmetrically on both chips, while dedicated spacers are introduced to limit the residual tilt. Here, we present a flip-chip bonding process based on an asymmetric indium architecture, combining $20\,μ\mathrm{m}$ thick indium bumps on the control chip with $200\,\mathrm{nm}$ thin indium pads on the qubit chip. Using electrical and microwave measurements, we demonstrate low resistance and low loss indium interconnects, and show that transmon qubits integrated with this process reach relaxation and coherence times of $T_1=(159\pm14)\,μ\mathrm{s}$ and $T_{\mathrm{2,echo}}=(294\pm42)\,μ\mathrm{s}$, respectively, comparable to planar devices. Combined with a multi angle compression procedure that suppresses systematic tilt, this approach reduces the average post bonding tilt to $(20\pm12)\,μ\mathrm{rad}$. These results establish an asymmetric indium architecture combined with multi angle compression as a robust, coherence preserving route toward 3D-integrated superconducting quantum processors.
AI Summary
The paper addresses inter-chip gap uniformity and coherence preservation in flip-chip superconducting circuits. It combines an asymmetric indium architecture—$20\,\mu\mathrm{m}$ bumps and SU-8 spacers on the control chip, with $200\,\mathrm{nm}$ pads on the qubit chip—with four room-temperature compression steps at successive $90^\circ$ orientations. This confines thick-resist processing to the control chip and compensates systematic bonder-induced tilt. SEM edge measurements and backside profilometry reconstruct the gap geometry. Relative to single-step bonding with spacers, multi-angle compression reduces mean tilt from $209\pm84\,\mu\mathrm{rad}$ to $20\pm12\,\mu\mathrm{rad}$ and RMS spatial gap variation from $418$ to $64\,\mathrm{nm}$, at a mean gap of $10.04\,\mu\mathrm{m}$. Four larger, $14.3\times14.3\,\mathrm{mm}^2$ assemblies show $23\pm8\,\mu\mathrm{rad}$ tilt and $158\,\mathrm{nm}$ RMS variation. Measurements of six transmons before and after assembly show comparable deviations from simulated circuit parameters. Single-photon resonator measurements give internal quality factors of $(1.93\pm0.40)\times10^6$ on the qubit chip and $(0.90\pm0.11)\times10^6$ on the control chip. A fit to resonators containing one to six inter-chip transitions estimates loss per transition below $10^{-7}$ at the stated $1\sigma$ level. Repeated measurements over 24 hours yield mean transmon $T_1=159\pm14\,\mu\mathrm{s}$ and $T_{2,\mathrm{echo}}=294\pm42\,\mu\mathrm{s}$; planar references have $T_1=167\pm34\,\mu\mathrm{s}$. Stated limitations include substantial transition-loss fit uncertainty from six resonators and device-to-device scatter, user-dependent manual rotation, and gap reconstruction assuming predominantly global tilt and bowing. Coherence comparisons establish no detectable added loss only within measurement sensitivity.
Error found: Section 4 claims that assembly-induced changes in circuit-target errors remain below the simulated 20 μrad tilt limit, although the mean resonator- and qubit-frequency errors change by 0.538 and 0.878 percentage points, respectively, exceeding its stated below-0.2% frequency-deviation scale. Section 4 incorrectly infers an insignificant resonator-error difference from overlapping standard deviations, whereas the six tabulated paired differences give t=4.04 and two-sided p≈0.010 under standard paired-test assumptions.
Written by gpt-6.1-sol from the paper's full text. Automated: it can be wrong.
- Comments
- 14 pages, 4 main figures, 5 appendix figures