The detection of gravitational waves in the low-frequency band (10 nHz to 1 micro-Hz) using inner solar system proof masses is severely limited by Newtonian gravity gradient noise (GGN) sourced by the asteroid belt. In this paper, we propose a novel detection concept that exploits the relativistic nature of gravitational waves to break the degeneracy between the signal and the asteroid GGN background. The non-relativistic motion of asteroids dominantly sources gravito-electric fields, with velocity suppressed gravito-magnetic components. Relativistic gravitational waves produce gravito-electric and gravito-magnetic components of equal magnitude. We propose detecting the gravito-magnetic component of low frequency gravitational waves using the Lorentz acceleration of test bodies. The measurement of this Lorentz acceleration is metrologically possible due to the fact that expected astrophysical sources of low frequency gravitational waves have considerably higher characteristic strains than the strains typically expected at higher frequencies. We show that this measurement allows for unambiguous extraction of the gravitational wave signal from the gravity gradient noise in a three satellite constellation. The gravito-magnetic measurement still requires a proof mass that is well isolated from non-gravitational noise. We propose the use of atom interferometers to serve as such a pristine inertial reference.
AI Summary
The paper asks whether inner-solar-system detectors can observe gravitational waves at $10\,\mathrm{nHz}$–$1\,\mu\mathrm{Hz}$ despite asteroid gravity-gradient noise (GGN), estimated to exceed the target gravito-electric signal by $10^2$–$10^4$. It proposes measuring gravito-magnetic tidal acceleration: gravitational waves have comparable electric and magnetic curvature components, whereas asteroid magnetic components are suppressed by orbital speeds of order $10^{-4}c$.
Using Fermi normal coordinates, it derives velocity-dependent satellite accelerations and intersatellite pulse-arrival-time observables. Multiple baselines and orbital modulation are used to separate these accelerations from Newtonian gradients. Orbital simulations indicate that three satellites in elliptical heliocentric orbits, separated by roughly $10^7\,\mathrm{km}$, can fit GGN terms through seventh order with an order-unity sensitivity penalty beyond the intrinsic velocity suppression. The required acceleration sensitivity is approximately $10^{-21}\,\mathrm{m\,s^{-2}/\sqrt{Hz}}$ near $10\,\mathrm{nHz}$.
A proposed inertial reference combines local atom interferometers with macroscopic optical proof masses. Indicative requirements include $10^4\,\mathrm{s}$ interrogation times, picokelvin atomic temperatures, phase sensitivity near $10^{-5}/\sqrt{\mathrm{Hz}}$, and shielded interrogation regions tens to hundreds of metres long.
The analysis does not establish a complete detector noise budget or broadband signal-extraction pipeline. Orbital mixing and spectral leakage remain untreated, particularly near the orbital frequency. Proof-mass construction, satellite self-gravity coupling, and several noise-mitigation schemes require further development. Pointing-noise rejection may require a fourth satellite or microarcsecond-level referencing; extraction penalties also depend on frequency and observation duration.
Little sign of AI-generated textOverclaimsStrong assumptionsPossible error
Central claim may not hold: The claimed unambiguous extraction is not established for broadband asteroid noise because the separation tests omit orbital mixing and leakage from other noise frequencies, an omission the paper explicitly acknowledges.
The elementary extraction incorrectly assigns its cubic coefficient solely to Newtonian gradients, omitting the first-order gravitational-wave contribution −(hω²/2)v_xT to the projected acceleration.
The elementary time-delay polynomial also uses the wrong displacement coefficient for linearly changing acceleration and neglects a changing-line-of-sight contribution of the same order as retained Newtonian terms.
Written by gpt-6.1-sol from the paper's full text. Automated: it can be wrong.
The detection of gravitational waves in the low-frequency band (10 nHz to 1 micro-Hz) using inner solar system proof masses is severely limited by Newtonian gravity gradient noise (GGN) sourced by the asteroid belt. In this paper, we propose a novel detection concept that exploits the relativistic nature of gravitational waves to break the degeneracy between the signal and the asteroid GGN background. The non-relativistic motion of asteroids dominantly sources gravito-electric fields, with velocity suppressed gravito-magnetic components. Relativistic gravitational waves produce gravito-electric and gravito-magnetic components of equal magnitude. We propose detecting the gravito-magnetic component of low frequency gravitational waves using the Lorentz acceleration of test bodies. The measurement of this Lorentz acceleration is metrologically possible due to the fact that expected astrophysical sources of low frequency gravitational waves have considerably higher characteristic strains than the strains typically expected at higher frequencies. We show that this measurement allows for unambiguous extraction of the gravitational wave signal from the gravity gradient noise in a three satellite constellation. The gravito-magnetic measurement still requires a proof mass that is well isolated from non-gravitational noise. We propose the use of atom interferometers to serve as such a pristine inertial reference.
The paper asks whether inner-solar-system detectors can observe gravitational waves at 10nHz–1μHz despite asteroid gravity-gradient noise (GGN), estimated to exceed the target gravito-electric signal by 102–104. It proposes measuring gravito-magnetic tidal acceleration: gravitational waves have comparable electric and magnetic curvature components, whereas asteroid magnetic components are suppressed by orbital speeds of order 10−4c.
Using Fermi normal coordinates, it derives velocity-dependent satellite accelerations and intersatellite pulse-arrival-time observables. Multiple baselines and orbital modulation are used to separate these accelerations from Newtonian gradients. Orbital simulations indicate that three satellites in elliptical heliocentric orbits, separated by roughly 107km, can fit GGN terms through seventh order with an order-unity sensitivity penalty beyond the intrinsic velocity suppression. The required acceleration sensitivity is approximately 10−21ms−2/Hz near 10nHz.
A proposed inertial reference combines local atom interferometers with macroscopic optical proof masses. Indicative requirements include 104s interrogation times, picokelvin atomic temperatures, phase sensitivity near 10−5/Hz, and shielded interrogation regions tens to hundreds of metres long.
The analysis does not establish a complete detector noise budget or broadband signal-extraction pipeline. Orbital mixing and spectral leakage remain untreated, particularly near the orbital frequency. Proof-mass construction, satellite self-gravity coupling, and several noise-mitigation schemes require further development. Pointing-noise rejection may require a fourth satellite or microarcsecond-level referencing; extraction penalties also depend on frequency and observation duration.
Matter-wave interferometers have fundamental applications for gravity experiments such as testing the equivalence principle and the quantum nature of gravity. In addition, matter-wave interferometers can be used as quantum sensors to measure the local gravitational acceleration caused by external massive moving objects, thus lending itself for technological applications. In this paper, we will establish a three-dimensional model to describe the gravity gradient signal from an external moving object, and theoretically investigate the achievable sensitivities using the matter-wave interferometer based on the Stern-Gerlach setup. As an application we will consider the mesoscopic interference for metric and curvature and gravitational-wave detection scheme [R. J. Marshman et al., Mesoscopic interference for metric and curvature (MIMAC) & gravitational wave detection, New J. Phys. 22, 083012 (2020)] and quantify its sensitivity to gravity gradients using frequency-space analysis. We will consider objects near Earth-based experiments and space debris in proximity of satellites and estimate the minimum detectable mass of the object as a function of their distance, velocity, and orientation.
In this white paper, we highlight the importance of the (1−10Hz) frequency range for laboratory tests of the quantum nature of gravity using the quantum gravity-induced entanglement of masses (QGEM) protocol. QGEM requires matter-wave interferometers with masses (m∼10−15−10−14kg), brought within separations (d∼30−50μm), while maintaining spatial superpositions of (1−20μm) and coherence for (τ∼0.1−1s). These requirements make low-frequency environmental noise a central experimental challenge and place QGEM in a regime closely related to the low-frequency goals of the Einstein Telescope (ET) and the Cosmic Explorer (CE). In particular, QGEM is sensitive to relative acceleration noise (RAN) and to gravity-gradient noise (GGN) generated by seismic and other environmental mass-density fluctuations. For representative parameters m=10−14kg, Δx=10μm, and τ=1s, the differential acceleration-noise amplitude spectral density must be suppressed well below the 10−15ms−2/Hz level to keep acceleration-induced dephasing below the relevant experimental scale. Achieving this level of low-frequency noise suppression is therefore a key requirement for QGEM and closely parallels the seismic and gravity-gradient noise challenges that ET and CE address.
Gravitational waves manifest as a time varying straining of space: they arise from the accelerating motions of large bodies of mass and propagate across the universe at the speed of light as ripples in the fabric of space-time, a fleetingly weak effect so far eluding direct detection. The detection of gravitation waves is expected to yield a rich vein to observational astronomy, complementing existing electromagnetic surveys and revealing a hitherto unexplored range of phenomena. First generation interferometric gravitational wave detectors, notably Enhanced LIGO, achieved strain sensitivities of one part in ten to power twenty-one per square-root-Hertz at 100 Hz with an expected detection rate of 2-3 events per year. Commissioning of a new generation of Advanced LIGO interferometric detectors has concluded recently with a resultant ten-fold sensitivity improvement. Overall their potential event detection space has increased by a factor of 1000. The quantum nature of light within these detectors now limits their sensitivity over most of their frequency range. This quantum noise limit is driven by the vacuum quadrature fluctuations propagated through their open detection ports and represents a fundamental noise floor to their strain sensitivity. This thesis addresses two distinct approaches to quantum noise improvement for future upgrades to advanced detectors. The first addresses the issue of quantum noise by adopting a quantum non-demolition approach to detector readout variables, the so-called `speed-meter’ design. Such a modified instrument samples test mass momentum, a quantity for which time separated measurements commute and are therefore not bound by Heisenberg-like limits. A novel polarisation-folded sloshing cavity type speed-meter is proposed where readout fields are stored and delayed in the orthogonal polarisation of the interferometer’s arms cavities. Here frequency dependence is selected to cancel position like measurements so that only test mass momentum information remains. A quantum noise propagation model is developed and a sensitivity performance is demonstrated that beats the standard quantum limit below 100 Hz over a broad range of frequencies. A second approach to achieve quantum noise enhancement in advanced detectors involves injection of quadrature-squeezed states in the place of vacuum. This dissertation details the development of a prototype squeezed vacuum source suitable to the demanding enhancement requirements for an Advanced LIGO squeezing installation. The construction of a doubly resonant, bow-tie cavity source is presented. This employs a novel monolithic all-glass cavity construction and is vacuum compatible. This design demonstrates the viability of building a cavity using optical contacting as a construction technique for attaching mounting prisms to highly polished fused-silica breadboards. Such a design can be expected to have excellent length noise stability, provide low intrinsic phase noise and would be suitable to mount on seismic isolation stages within the LIGO vacuum envelope. Further, the travelling wave cavity design should provide excellent 50 dB intrinsic backscatter isolation. We demonstrate the first operation of such a complex non-linear device under vacuum, producing 8.6 dB of measured vacuum squeezing down to 10 Hz across the advanced LIGO ‘audio-band’ detection range.
Gravitational-wave astronomy promises a radically new method of investigating the universe, one that does not detect elementary particles, but rather ripples in space-time itself. One might expect that with this radically new method, our understanding of the universe will make an equally giant leap. One of the most promising methods for the eventual detection of gravitational-waves is that of interferometric gravitational-wave detection. The sensitivity of these devices is nothing short of amazing, and their sensitivity continues to improve. The next generation of detectors are expected reach a point where increasing the laser power, previously used to increase the sensitivity, is no longer expected to provide any benefit. One of the most promising options for further increasing the sensitivity, through reduction of the quantum noise, is via the application of "squeezed states of light". Squeezed states of light are light fields for which the noise of some observable has been reduced below the quantum noise limit. These states have been shown for many years to offer increased sensitivity in interferometers and recently in interferometric gravitational-wave detectors. One of the most challenging tasks to make suitable squeezed light sources for these detectors is to produce low-frequency squeezing, corresponding to the detection band of these interferometers. This thesis details the doubly resonant travelling wave bow-tie squeezer as a source of squeezing for interferometric gravitational-wave detection. This squeezer achieves record results of squeezing in the gravitational-wave detection band. For the first time, 10 dB of shot noise suppression at 10Hz is directly observed and above 200Hz, 11.6 dB is observed. The work presented in this thesis provides evidence that further substantiates previous progress indicating that squeezed states of light are now ready for full-time integration into interferometric gravitational-wave detectors. The new cavity design, described in detail throughout this thesis, is shown to outperform previous designs and provide benefits when integrating squeezing into these detectors, in particular, isolation to backscattered light from the interferometer. The noise sources that typically lead to degradation in squeezing measurements are investigated and discussed. Additionally, a modification to the standard locking technique used to control these vacuum squeezed states, coherent locking, is presented and discussed. The modified technique reduces the required number of locking loops and provides a larger beat note from which to derive an error signal for one of the remaining loops. A squeezer using these design philosophies is then constructed and used to inject squeezing into the LIGO gravitational-wave detector. Injection of the squeezed state provides enhancement of the sensitivity of the detector at frequencies around 200Hz and above. The sensitivity seen was equivalent to approximately 2 dB of shot noise reduction. The enhancement is limited by the loss within the interferometer. Injection of the squeezed state did not show any degradation in the sensitivity of the device below 200Hz, indicating for the first time that noise couplings between the interferometer and the squeezer could be sufficiently suppressed at these frequencies even for the most sensitive detectors.
Abstract Recent advances in quantum sensing—optical clocks at 5.5 × 10 − 19 systematic uncertainty, frequency-dependent squeezing below the standard quantum limit, quantum magnetometers approaching fundamental sensitivity limits—raise a natural question: can these technologies detect gravitational waves directly, or enhance existing detectors beyond current capabilities? We show that the answer is primarily determined by the coupling mechanism between the gravitational wave and the sensor. Starting from the tidal Hamiltonian in Fermi normal coordinates, we identify three physically distinct mechanisms by which a gravitational wave couples directly to a quantum system, and derive their transducer gains within linearized general relativity and non-relativistic quantum mechanics. Internal atomic coupling (tidal distortion of electronic wavefunctions) yields a transducer gain G A = 2.4 × 10 − 20 , with vanishing first-order energy shifts for all J = 0 clock states—a ∼ 10 35 deficit relative to laser interferometry that exceeds any projected quantum enhancement. Center-of-mass coupling (Doppler shifts from geodesic motion) reaches strain sensitivities of ∼ 10 − 18 , still 10 4 above LISA requirements. Light propagation coupling (phase accumulation over macroscopic baselines) provides the enormous transducer gain that makes laser interferometry—and atom interferometry—viable. For detectors exploiting this third mechanism, we quantify how much improvement quantum sensors can provide through the detector’s noise architecture: LISA’s noise budget is predominantly classical, limiting combined quantum enhancement to E ≈ 1.04 , while ground-based detectors in the shot-noise-dominated regime achieve E = 1.6 – 2.1 . Atom interferometers exploit the same light-propagation mechanism to target the 0.01–10 Hz band between the LISA and LIGO ranges.
The ability to directly detect gravitational waves will open a completely new branch of astronomy to view the Universe, one that is inaccessible to electromagnetic-based astronomy. First generation ground-based interferometric gravitational-wave detectors have achieved strain sensitivities of order one part in ten to the twenty-one, at 100 Hz detection frequency. A new generation of detectors are under construction, designed to improve on the sensitivity of the first-generation detectors by a factor of 10. The quantum nature of light will broadly limit the sensitivity of these new instruments. This quantum noise will originate from the quantum vacuum fluctuations that enter the unused port of the interferometer. One of the most promising options for reducing the quantum noise impact and further increasing the sensitivity is applying quantum squeezed vacuum states. These squeezed states have lower noise in one quadrature than the vacuum state. By replacing the quantum vacuum fluctuations entering the interferometer with squeezed vacuum states, the quantum noise impact is reduced. This thesis firstly details the development of a squeezed light source that produces squeezed states applicable for enhancing interferometric gravitational-wave detectors. A doubly-resonant, travelling-wave bow-tie cavity squeezed light source is presented. For the first time, greater than 10 dB of quantum noise suppression across the gravitational-wave detection band is directly observed, and 11.6 dB of quantum noise suppression is observed above 200 Hz. This squeezing cavity design also has benefits with intrinsic isolation to backscattered light. Experiments that quantify this isolation are reported. The properties affecting squeezing magnitude and low-frequency squeezing measurement are discussed. In addition, a modified squeezing-ellipse-phase control technique for squeezed vacuum states is presented. This thesis secondly presents results from the LIGO Squeezed Light Injection Experiment, undertaken to test squeezed light injection into a 4 km interferometric gravitational-wave detector. The results of the experiment show the first measurement of squeezing-enhancement in a 4 km gravitational-wave detector, with 2.15 dB measured above 250 Hz. This represents the best sensitivity to gravitational waves yet achieved at these frequencies by any single gravitational-wave detector to date. An unknown area was whether the addition of a squeezer would introduce noise couplings that degrade the crucial low frequency sensitivity. The results demonstrate that injected squeezed states are compatible with low frequency gravitational-wave measurement. The characterisation of squeezing-injection optical losses and fluctuations of the squeezing angle are also reported. The knowledge and processes gained, from both the squeezed light source development work and the LIGO Squeezed Light Injection Experiment, will inform the design, planning and implementation of squeezed states in future gravitational-wave detectors.