Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2602.12248 · Physical review. B./Physical review. B

Simultaneous high-fidelity readout and strong coupling in a donor-based spin qubit

Si Yan Koh, Weifan Wu, Kelvin Onggadinata, Arghya Maity, Mark Chiyuan Ma, Calvin Pei Yu Wong, Kuan Eng Johnson Goh, Bent Weber, Hui Khoon Ng, Teck Seng Koh

Published Apr 22, 2026• 0 citations
arXivHTMLPDF

Abstract

Superconducting resonators coupled to solid-state qubits offer a scalable architecture for long-range entangling operations and fast, high-fidelity readout. Realizing this requires low photon-loss rates and qubits with tunable electric dipole moments that couple strongly to the resonator's electric field while maintaining long coherence times. For spin qubits, spin-photon coupling is typically achieved via spin-charge hybridization. However, this introduces a fundamental trade-off: a large spin-charge admixture enhances the coupling strength, which boosts readout and resonator-mediated gate speeds, but exposes the qubit to increased decoherence, thereby increasing the threshold required for strong coupling and limiting the time available for accurate state measurement. This makes it essential to identify optimal operating points for each qubit platform. We address this for the donor-based flip-flop qubit, whose microwave-controllable electron-nuclear spin states make it suitable for coupling to microwave resonators. We demonstrate that, by choosing intermediate tunnel couplings that balance strong interaction with long qubit lifetimes, high-fidelity readout and strong coupling are simultaneously achievable. We also map out the respective charge-photon couplings and photon-loss rates required. Furthermore, we show that experimental constraints on charge-photon coupling and photon loss can be mitigated using squeezed input fields. As similar trade-offs appear in quantum-dot-based qubits, our methods and insights extend naturally to these platforms, offering a potential route toward scalable architectures.

DOI
10.1103/7f91-6g8y

Related papers

Optimal dispersive readout of a spin qubit with a microwave resonator

Benjamin D’Anjou, Guido Burkard

Strong coupling of semiconductor spin qubits to superconducting microwave resonators was recently demonstrated [X. Mi et al., Nature 555, 599 (2018); A. J. Landig et al., Nature 560, 179 (2018); N. Samkharadze et al., Science 359, 1123 (2018); T. Cubaynes et al., NPJ Quant. Inf. 5, 47 (2019)]. These breakthroughs pave the way for quantum information processing that combines the long coherence times of solid-state spin qubits with the long-distance connectivity, fast control, and fast high-fidelity quantum-non-demolition readout of existing superconducting qubit implementations. Here we theoretically analyze and optimize the dispersive readout of a single spin in a semiconductor double quantum dot (DQD) coupled to a microwave resonator via its electric dipole moment. The strong spin-photon coupling arises from the motion of the electron spin in a local magnetic field gradient. We calculate the signal-to-noise ratio (SNR) of the readout accounting for both Purcell spin relaxation and spin relaxation arising from intrinsic electric noise within the semiconductor. We express the maximum achievable SNR in terms of the cooperativity associated with these two dissipation processes. We find that while the cooperativity increases with the strength of the dipole coupling between the DQD and the resonator, it does not depend on the strength of the magnetic field gradient. We then optimize the SNR as a function of experimentally tunable DQD parameters. We identify wide regions of parameter space where the unwanted backaction of the resonator photons on the qubit is small. Moreover, we find that the coupling of the resonator to other DQD transitions can enhance the SNR by at least a factor of two, a ``straddling'' effect [J. Koch et al., Phys. Rev. A 76, 042319 (2007)] that occurs only at nonzero energy detuning of the DQD double-well potential. We estimate that with current technology, single-shot readout fidelities in the range 82--95% can be achieved within a few $\ensuremath{\mu}\mathrm{s}$ of readout time without requiring the use of Purcell filters.

arXiv:1905.09702•Physical review. B./Physical review. B•Dec 23, 2019•48 citations

Fast readout of quantum dot spin qubits via Andreev spins

Anonymous, Katharina Laubscher, Patrick Del Vecchio +3 more

Spin qubits in semiconducting quantum dots are currently limited by slow readout processes, which are orders of magnitude slower than gate operations. In contrast, Andreev spin qubits benefit from fast measurement schemes enabled by the large resonator couplings of superconducting qubits but suffer from reduced coherence during qubit operations. Here, we propose fast and high-fidelity measurement protocols based on an electrically tunable coupling between quantum dot and Andreev spin qubits. In realistic devices, this coupling can be made sufficiently strong to enable high-fidelity readout well below microseconds, potentially enabling mid-circuit measurements. Crucially, the electrical tunability of our coupler permits to switch it off during idle periods, minimizing crosstalk and measurement back-action. Our approach is fully compatible with germanium-based devices and paves the way for scalable quantum computing architectures by leveraging the advantages of heterogeneous qubit implementations.

arXiv:2506.19762•Physical Review Applied•Aug 5, 2026•6 citations

High-fidelity regimes of resonator-mediated controlled-Z gates between quantum-dot qubits

Guangzhao Yang, Marek Gluza, Si Yan Koh +6 more

Semiconductor double quantum dot (DQD) qubits coupled via superconducting microwave resonators provide a powerful means of long-range manipulation of the qubits' spin and charge degrees of freedom. Quantum gates can be implemented by parametrically driving the qubits while their transition frequencies are detuned from the resonator frequency. Long-range two-qubit controlled-Z (CZ) gates have been proposed for the DQD spin qubit within the rotating-wave approximation (RWA). Rapid gates demand strong coupling, but RWA breaks down when coupling strengths become significant relative to system frequencies. Therefore, understanding the errors arising from approximations used is critical for high-fidelity operation. Here, we go beyond RWA to study CZ gate fidelity for both DQD spin and charge qubits. We propose a novel parametric drive on the charge qubit that produces smaller errors and show that the fidelity of the CZ gate outperforms its spin counterpart, resulting in a much smaller fidelity loss of $0.05\%$ compared to $0.80\%$ for the spin qubit, and greater robustness against qubit dephasing and photon loss. We find that drive amplitude -- a parameter dropped in RWA -- is critical for optimizing fidelity, with the charge qubit exhibiting better tolerance to drive amplitude variations. Our results demonstrate the necessity of going beyond RWA in understanding how long-range gates can be realized in DQD qubits, with charge qubits offering considerable advantages in high-fidelity operation.

arXiv:2512.00761•Nov 30, 2025•0 citations

Strong coupling of hybrid system between semiconductor quantum dots and superconducting resonator

Mingbo Chen, Yong-Qiang Xu, Gang Cao +1 more

Quantum computing is a powerful way of improving computing efficiency. For some specific problems, quantum processor can exponentially reduce computation time compared to the classical computer. Cavity quantum electrodynamics, which studies the coherent interaction between photons in an optical cavity and atoms or other two-level systems, is of enormous significance to quantum computing and quantum information processing. The strong coupling regime where a cavity photon mode and an atom exchange a single quantum energy coherently has attracted extensive interest in varied experimental platforms and systems such as alkali atoms, Rydberg atoms, large spin ensembles, magnons, etc. The semiconductor gate-defined double quantum dot (DQD) system is one of the most promising platforms that possesses advantages of advanced micro-nano processing technology and outstanding scalability. Introducing the concept of cavity QED into superconducting circuits (circuit QED, cQED), provides an opportunity to study interaction between electrons confined in semiconductor DQD and photons trapped in a superconducting resonator. Reaching strong coupling regime in this hybrid system paves the way to large-scale network of quantum computing. Electrons confined in DQD have large electrical dipoles, thus are able to couple to photons with relatively large coupling rate. Whereas, due to the charge noise and other dissipation channels in the hybrid system, the decoherence rate of the system is larger than the coupling rate, leaving the strong coupling a great challenge. In recent years, different methods have been proposed to access the strong coupling regime. Taking advantage of a high-quality heterojunction structure, an overlapping gate architecture and a low-pass LC filter on the DC bias line, the decoherence of the charge qubit and microwave leakage of the resonator can be effectively suppressed. The coupling strength of the hybrid system can be improved utilizing a high impedance resonator which is comprised of high kinetic inductance materials. Spin, which does not interact directly with the electric field, is insensitive to charge noise and has much longer decoherence time than charge qubit. However, the weak interaction results in a small coupling rate between the spin and the photon. To solve this problem, the method of coherent hybridization between the spin and the charge state is proposed to improve the coupling strength. This hybridization can be achieved by applying a non-uniform magnetic field, utilizing spin-orbit interaction or spin exchange interaction. At present, both charge qubits and spin qubits have achieved strong coupling with the cavity and the coupling distance between long-range qubits is greatly expanded as long as millimeters. This review introduces basic ideas about cQED and fundamental elements in semiconductor cQED systems. Recent progress in strong coupling hybrid system and methods for improving coupling structures are discussed. In future research, more efforts will be devoted into long-range transfer of qubit states and photon-mediated two or multi-qubit gates.

Chinese Science Bulletin (Chinese Version)•Apr 24, 2020•0 citations

Input-output theory for spin-photon coupling in Si double quantum dots

Mónica Benito, Xiao Mi, Jacob M. Taylor +2 more

The interaction of qubits via microwave frequency photons enables long-distance qubit-qubit coupling and facilitates the realization of a large-scale quantum processor. However, qubits based on electron spins in semiconductor quantum dots have proven challenging to couple to microwave photons. In this theoretical work we show that a sizable coupling for a single electron spin is possible via spin-charge hybridization using a magnetic field gradient in a silicon double quantum dot. Based on parameters already shown in recent experiments, we predict optimal working points to achieve a coherent spin-photon coupling, an essential ingredient for the generation of long-range entanglement. Furthermore, we employ input-output theory to identify observable signatures of spin-photon coupling in the cavity output field, which may provide guidance to the experimental search for strong coupling in such spin-photon systems and opens the way to cavity-based readout of the spin qubit.

arXiv:1710.02508•Physical review. B./Physical review. B•Dec 22, 2017•111 citations

Resonator-based Hole Spin Qubit Readout

Eoin G. Kelly

Spin qubits in gate-defined semiconductor quantum dots are a promising platform for realising a scalable quantum computer. This platform encodes quantum information into the intrinsic angular momentum (spin) of individual electrons or holes. In particular, hole spins in quantum dots enable the possibility of all-electrical spin control due to their intrinsic spin-orbit coupling. One important criterion of a quantum computer is the ability to reliably read out the state of the qubit. This is done by mapping spin information to the charge degree of freedom, combined with a method for charge detection. Charge detection can be facilitated by coupling a resonator directly to the quantum dot gate or to a charge sensor and measuring the resonator's phase or amplitude response. In this thesis, we describe a set of experiments relating to the implementation of hole spin qubit readout with superconducting resonators. First, we study gate-based charge sensing in a Si fin field-effect transistor (finFET) device using a superconducting NbN nanowire resonator. We find that the resonator amplifies capacitive crosstalk when electrical control pulses are applied to gate electrodes in this device. This occurs whenever a spectral component of qubit control pulses overlaps with the resonance frequency, which we show may occur for both baseband and radio-frequency (RF) drive signals. We quantify this crosstalk in a transport-based method, and attribute its source to the capacitance between the bondpads of neighbouring gate electrodes. In a second experiment, we use an RF charge sensor with the same nanowire technology to read out hole spin qubits formed in the quantum well of a Ge/SiGe heterostructure. A screening layer approach is used to facilitate RF matching due to large RF dissipation found in the heterostructure. We implement a double-latched readout scheme in this system to reduce errors arising from both spin and charge decay during readout. The spin-to-charge conversion process and its dependence on magnetic field orientation is studied. Spin and charge decay processes arising after spin-to-charge conversion are mitigated by choosing an optimal working point for the field orientation, field amplitude and readout pulse times. By doing so, we achieve an average single-shot state-preparation-and-measurement fidelity of 97%, primarily bounded by imperfect state preparation and limited signal-to-noise ratio. Finally, we study coplanar waveguide resonators fabricated from NbN. We investigate the feasibility of integrating this type of resonator onto the same chip as the Si finFET quantum dots. We then develop a novel resonator readout technique by the interference of two microwave sidebands. We demonstrate the insensitivity of this technique to common-mode phase and amplitude noise both theoretically and experimentally. This technique is then used to study resonator noise arising from two-level system defects. These results highlight both the practical constraints and the potential for achieving high readout fidelities using resonator-based hole spin qubit readout. This work establishes a blueprint for mitigating resonator-induced crosstalk and enabling high-fidelity readout in lossy materials by incorporating a screening layer.

•Jan 1, 2025•0 citations
Superconducting resonators coupled to solid-state qubits offer a scalable architecture for long-range entangling operations and fast, high-fidelity readout. Realizing this requires low photon-loss rates and qubits with tunable electric dipole moments that couple strongly to the resonator's electric field while maintaining long coherence times. For spin qubits, spin-photon coupling is typically achieved via spin-charge hybridization. However, this introduces a fundamental trade-off: a large spin-charge admixture enhances the coupling strength, which boosts readout and resonator-mediated gate speeds, but exposes the qubit to increased decoherence, thereby increasing the threshold required for strong coupling and limiting the time available for accurate state measurement. This makes it essential to identify optimal operating points for each qubit platform. We address this for the donor-based flip-flop qubit, whose microwave-controllable electron-nuclear spin states make it suitable for coupling to microwave resonators. We demonstrate that, by choosing intermediate tunnel couplings that balance strong interaction with long qubit lifetimes, high-fidelity readout and strong coupling are simultaneously achievable. We also map out the respective charge-photon couplings and photon-loss rates required. Furthermore, we show that experimental constraints on charge-photon coupling and photon loss can be mitigated using squeezed input fields. As similar trade-offs appear in quantum-dot-based qubits, our methods and insights extend naturally to these platforms, offering a potential route toward scalable architectures.
Strong coupling of semiconductor spin qubits to superconducting microwave resonators was recently demonstrated [X. Mi et al., Nature 555, 599 (2018); A. J. Landig et al., Nature 560, 179 (2018); N. Samkharadze et al., Science 359, 1123 (2018); T. Cubaynes et al., NPJ Quant. Inf. 5, 47 (2019)]. These breakthroughs pave the way for quantum information processing that combines the long coherence times of solid-state spin qubits with the long-distance connectivity, fast control, and fast high-fidelity quantum-non-demolition readout of existing superconducting qubit implementations. Here we theoretically analyze and optimize the dispersive readout of a single spin in a semiconductor double quantum dot (DQD) coupled to a microwave resonator via its electric dipole moment. The strong spin-photon coupling arises from the motion of the electron spin in a local magnetic field gradient. We calculate the signal-to-noise ratio (SNR) of the readout accounting for both Purcell spin relaxation and spin relaxation arising from intrinsic electric noise within the semiconductor. We express the maximum achievable SNR in terms of the cooperativity associated with these two dissipation processes. We find that while the cooperativity increases with the strength of the dipole coupling between the DQD and the resonator, it does not depend on the strength of the magnetic field gradient. We then optimize the SNR as a function of experimentally tunable DQD parameters. We identify wide regions of parameter space where the unwanted backaction of the resonator photons on the qubit is small. Moreover, we find that the coupling of the resonator to other DQD transitions can enhance the SNR by at least a factor of two, a ``straddling'' effect [J. Koch et al., Phys. Rev. A 76, 042319 (2007)] that occurs only at nonzero energy detuning of the DQD double-well potential. We estimate that with current technology, single-shot readout fidelities in the range 82--95% can be achieved within a few $\ensuremath{\mu}\mathrm{s}$ of readout time without requiring the use of Purcell filters.
Spin qubits in semiconducting quantum dots are currently limited by slow readout processes, which are orders of magnitude slower than gate operations. In contrast, Andreev spin qubits benefit from fast measurement schemes enabled by the large resonator couplings of superconducting qubits but suffer from reduced coherence during qubit operations. Here, we propose fast and high-fidelity measurement protocols based on an electrically tunable coupling between quantum dot and Andreev spin qubits. In realistic devices, this coupling can be made sufficiently strong to enable high-fidelity readout well below microseconds, potentially enabling mid-circuit measurements. Crucially, the electrical tunability of our coupler permits to switch it off during idle periods, minimizing crosstalk and measurement back-action. Our approach is fully compatible with germanium-based devices and paves the way for scalable quantum computing architectures by leveraging the advantages of heterogeneous qubit implementations.
Semiconductor double quantum dot (DQD) qubits coupled via superconducting microwave resonators provide a powerful means of long-range manipulation of the qubits' spin and charge degrees of freedom. Quantum gates can be implemented by parametrically driving the qubits while their transition frequencies are detuned from the resonator frequency. Long-range two-qubit controlled-Z (CZ) gates have been proposed for the DQD spin qubit within the rotating-wave approximation (RWA). Rapid gates demand strong coupling, but RWA breaks down when coupling strengths become significant relative to system frequencies. Therefore, understanding the errors arising from approximations used is critical for high-fidelity operation. Here, we go beyond RWA to study CZ gate fidelity for both DQD spin and charge qubits. We propose a novel parametric drive on the charge qubit that produces smaller errors and show that the fidelity of the CZ gate outperforms its spin counterpart, resulting in a much smaller fidelity loss of 0.05%0.05\%0.05% compared to 0.80%0.80\%0.80% for the spin qubit, and greater robustness against qubit dephasing and photon loss. We find that drive amplitude -- a parameter dropped in RWA -- is critical for optimizing fidelity, with the charge qubit exhibiting better tolerance to drive amplitude variations. Our results demonstrate the necessity of going beyond RWA in understanding how long-range gates can be realized in DQD qubits, with charge qubits offering considerable advantages in high-fidelity operation.
Quantum computing is a powerful way of improving computing efficiency. For some specific problems, quantum processor can exponentially reduce computation time compared to the classical computer. Cavity quantum electrodynamics, which studies the coherent interaction between photons in an optical cavity and atoms or other two-level systems, is of enormous significance to quantum computing and quantum information processing. The strong coupling regime where a cavity photon mode and an atom exchange a single quantum energy coherently has attracted extensive interest in varied experimental platforms and systems such as alkali atoms, Rydberg atoms, large spin ensembles, magnons, etc. The semiconductor gate-defined double quantum dot (DQD) system is one of the most promising platforms that possesses advantages of advanced micro-nano processing technology and outstanding scalability. Introducing the concept of cavity QED into superconducting circuits (circuit QED, cQED), provides an opportunity to study interaction between electrons confined in semiconductor DQD and photons trapped in a superconducting resonator. Reaching strong coupling regime in this hybrid system paves the way to large-scale network of quantum computing. Electrons confined in DQD have large electrical dipoles, thus are able to couple to photons with relatively large coupling rate. Whereas, due to the charge noise and other dissipation channels in the hybrid system, the decoherence rate of the system is larger than the coupling rate, leaving the strong coupling a great challenge. In recent years, different methods have been proposed to access the strong coupling regime. Taking advantage of a high-quality heterojunction structure, an overlapping gate architecture and a low-pass LC filter on the DC bias line, the decoherence of the charge qubit and microwave leakage of the resonator can be effectively suppressed. The coupling strength of the hybrid system can be improved utilizing a high impedance resonator which is comprised of high kinetic inductance materials. Spin, which does not interact directly with the electric field, is insensitive to charge noise and has much longer decoherence time than charge qubit. However, the weak interaction results in a small coupling rate between the spin and the photon. To solve this problem, the method of coherent hybridization between the spin and the charge state is proposed to improve the coupling strength. This hybridization can be achieved by applying a non-uniform magnetic field, utilizing spin-orbit interaction or spin exchange interaction. At present, both charge qubits and spin qubits have achieved strong coupling with the cavity and the coupling distance between long-range qubits is greatly expanded as long as millimeters. This review introduces basic ideas about cQED and fundamental elements in semiconductor cQED systems. Recent progress in strong coupling hybrid system and methods for improving coupling structures are discussed. In future research, more efforts will be devoted into long-range transfer of qubit states and photon-mediated two or multi-qubit gates.
The interaction of qubits via microwave frequency photons enables long-distance qubit-qubit coupling and facilitates the realization of a large-scale quantum processor. However, qubits based on electron spins in semiconductor quantum dots have proven challenging to couple to microwave photons. In this theoretical work we show that a sizable coupling for a single electron spin is possible via spin-charge hybridization using a magnetic field gradient in a silicon double quantum dot. Based on parameters already shown in recent experiments, we predict optimal working points to achieve a coherent spin-photon coupling, an essential ingredient for the generation of long-range entanglement. Furthermore, we employ input-output theory to identify observable signatures of spin-photon coupling in the cavity output field, which may provide guidance to the experimental search for strong coupling in such spin-photon systems and opens the way to cavity-based readout of the spin qubit.
Spin qubits in gate-defined semiconductor quantum dots are a promising platform for realising a scalable quantum computer. This platform encodes quantum information into the intrinsic angular momentum (spin) of individual electrons or holes. In particular, hole spins in quantum dots enable the possibility of all-electrical spin control due to their intrinsic spin-orbit coupling. One important criterion of a quantum computer is the ability to reliably read out the state of the qubit. This is done by mapping spin information to the charge degree of freedom, combined with a method for charge detection. Charge detection can be facilitated by coupling a resonator directly to the quantum dot gate or to a charge sensor and measuring the resonator's phase or amplitude response. In this thesis, we describe a set of experiments relating to the implementation of hole spin qubit readout with superconducting resonators. First, we study gate-based charge sensing in a Si fin field-effect transistor (finFET) device using a superconducting NbN nanowire resonator. We find that the resonator amplifies capacitive crosstalk when electrical control pulses are applied to gate electrodes in this device. This occurs whenever a spectral component of qubit control pulses overlaps with the resonance frequency, which we show may occur for both baseband and radio-frequency (RF) drive signals. We quantify this crosstalk in a transport-based method, and attribute its source to the capacitance between the bondpads of neighbouring gate electrodes. In a second experiment, we use an RF charge sensor with the same nanowire technology to read out hole spin qubits formed in the quantum well of a Ge/SiGe heterostructure. A screening layer approach is used to facilitate RF matching due to large RF dissipation found in the heterostructure. We implement a double-latched readout scheme in this system to reduce errors arising from both spin and charge decay during readout. The spin-to-charge conversion process and its dependence on magnetic field orientation is studied. Spin and charge decay processes arising after spin-to-charge conversion are mitigated by choosing an optimal working point for the field orientation, field amplitude and readout pulse times. By doing so, we achieve an average single-shot state-preparation-and-measurement fidelity of 97%, primarily bounded by imperfect state preparation and limited signal-to-noise ratio. Finally, we study coplanar waveguide resonators fabricated from NbN. We investigate the feasibility of integrating this type of resonator onto the same chip as the Si finFET quantum dots. We then develop a novel resonator readout technique by the interference of two microwave sidebands. We demonstrate the insensitivity of this technique to common-mode phase and amplitude noise both theoretically and experimentally. This technique is then used to study resonator noise arising from two-level system defects. These results highlight both the practical constraints and the potential for achieving high readout fidelities using resonator-based hole spin qubit readout. This work establishes a blueprint for mitigating resonator-induced crosstalk and enabling high-fidelity readout in lossy materials by incorporating a screening layer.