Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1905.09702 · Physical review. B./Physical review. B

Optimal dispersive readout of a spin qubit with a microwave resonator

Benjamin D’Anjou, Guido Burkard

Published Dec 23, 2019• 48 citations
arXivHTMLPDF

Abstract

Strong coupling of semiconductor spin qubits to superconducting microwave resonators was recently demonstrated [X. Mi et al., Nature 555, 599 (2018); A. J. Landig et al., Nature 560, 179 (2018); N. Samkharadze et al., Science 359, 1123 (2018); T. Cubaynes et al., NPJ Quant. Inf. 5, 47 (2019)]. These breakthroughs pave the way for quantum information processing that combines the long coherence times of solid-state spin qubits with the long-distance connectivity, fast control, and fast high-fidelity quantum-non-demolition readout of existing superconducting qubit implementations. Here we theoretically analyze and optimize the dispersive readout of a single spin in a semiconductor double quantum dot (DQD) coupled to a microwave resonator via its electric dipole moment. The strong spin-photon coupling arises from the motion of the electron spin in a local magnetic field gradient. We calculate the signal-to-noise ratio (SNR) of the readout accounting for both Purcell spin relaxation and spin relaxation arising from intrinsic electric noise within the semiconductor. We express the maximum achievable SNR in terms of the cooperativity associated with these two dissipation processes. We find that while the cooperativity increases with the strength of the dipole coupling between the DQD and the resonator, it does not depend on the strength of the magnetic field gradient. We then optimize the SNR as a function of experimentally tunable DQD parameters. We identify wide regions of parameter space where the unwanted backaction of the resonator photons on the qubit is small. Moreover, we find that the coupling of the resonator to other DQD transitions can enhance the SNR by at least a factor of two, a ``straddling'' effect [J. Koch et al., Phys. Rev. A 76, 042319 (2007)] that occurs only at nonzero energy detuning of the DQD double-well potential. We estimate that with current technology, single-shot readout fidelities in the range 82--95% can be achieved within a few $\ensuremath{\mu}\mathrm{s}$ of readout time without requiring the use of Purcell filters.

DOI
10.1103/physrevb.100.245427

Related papers

Simultaneous high-fidelity readout and strong coupling in a donor-based spin qubit

Si Yan Koh, Weifan Wu, Kelvin Onggadinata +7 more

Superconducting resonators coupled to solid-state qubits offer a scalable architecture for long-range entangling operations and fast, high-fidelity readout. Realizing this requires low photon-loss rates and qubits with tunable electric dipole moments that couple strongly to the resonator's electric field while maintaining long coherence times. For spin qubits, spin-photon coupling is typically achieved via spin-charge hybridization. However, this introduces a fundamental trade-off: a large spin-charge admixture enhances the coupling strength, which boosts readout and resonator-mediated gate speeds, but exposes the qubit to increased decoherence, thereby increasing the threshold required for strong coupling and limiting the time available for accurate state measurement. This makes it essential to identify optimal operating points for each qubit platform. We address this for the donor-based flip-flop qubit, whose microwave-controllable electron-nuclear spin states make it suitable for coupling to microwave resonators. We demonstrate that, by choosing intermediate tunnel couplings that balance strong interaction with long qubit lifetimes, high-fidelity readout and strong coupling are simultaneously achievable. We also map out the respective charge-photon couplings and photon-loss rates required. Furthermore, we show that experimental constraints on charge-photon coupling and photon loss can be mitigated using squeezed input fields. As similar trade-offs appear in quantum-dot-based qubits, our methods and insights extend naturally to these platforms, offering a potential route toward scalable architectures.

arXiv:2602.12248•Physical review. B./Physical review. B•Apr 22, 2026•0 citations

Fast and high-fidelity dispersive readout of a spin qubit with squeezed microwave and resonator nonlinearity

Chon‐Fai Kam, Xuedong Hu

Fast and high-fidelity qubit measurement is essential for quantum error correction in universal quantum computing. This study examines dispersive measurement of a spin in a semiconductor double quantum dot using a nonlinear microwave resonator. By employing displaced squeezed vacuum states, we achieve rapid, high-fidelity readout for silicon spin qubits. Our results show that modest squeezing and mild nonlinearity significantly enhance the signal-to-noise ratio (SNR) and the fidelity of qubit-state readout. By optimally adjusting the phases of squeezing and nonlinearity, we reduce readout time to sub-microsecond ranges. With current technology parameters ( κ ≈ 2 χ s , χ s /(2 π ) ≈ 0.15 MHz), utilizing a displaced squeezed vacuum state with 30 photons and a modest squeezing parameter r ≈ 0.6, along with a nonlinear microwave resonator charactered by a strength of λ ≈ − 1.2 χ s , a readout fidelity of 98% can be attained within a readout time of around 0.6 μ s.

arXiv:2401.03617•npj Quantum Information•Dec 28, 2024•16 citations

Enhancing Dispersive Readout of Superconducting Qubits through Dynamic Control of the Dispersive Shift: Experiment and Theory

François Swiadek, Ross Shillito, Paul Magnard +9 more

The performance of a wide range of quantum computing algorithms and protocols depends critically on the fidelity and speed of the employed qubit readout. Examples include gate sequences benefiting from midcircuit real-time measurement-based feedback, such as qubit initialization, entanglement generation, teleportation, and, perhaps most importantly, quantum error correction. A prominent and widely used readout approach is based on the dispersive interaction of a superconducting qubit strongly coupled to a large-bandwidth readout resonator, frequently combined with a dedicated or shared Purcell filter protecting qubits from decay. By dynamically reducing the qubit-resonator detuning and thus increasing the dispersive shift, we demonstrate a beyond-state-of-the-art two-state-readout error of only 0.25% in 100-ns integration time. Maintaining low-readout-drive strength, we nearly quadruple the signal-to-noise ratio of the readout by doubling the readout-mode line width, which we quantify by considering the hybridization of the readout resonator and its dedicated Purcell filter. We find excellent agreement between our experimental data and our theoretical model. The presented results are expected to further boost the performance of new and existing algorithms and protocols critically depending on high-fidelity fast midcircuit measurements. Published by the American Physical Society 2024

arXiv:2307.07765•PRX Quantum•Nov 20, 2024•81 citations

Coupling a single electron spin to a microwave resonator: controlling transverse and longitudinal couplings

Félix Beaudoin, Dany Lachance-Quirion, W. A. Coish +1 more

Microwave-frequency superconducting resonators are ideally suited to perform dispersive qubit readout, to mediate two-qubit gates, and to shuttle states between distant quantum systems. A prerequisite for these applications is a strong qubit-resonator coupling. Strong coupling between an electron-spin qubit and a microwave resonator can be achieved by correlating spin- and orbital degrees of freedom. This correlation can be achieved through the Zeeman coupling of a single electron in a double quantum dot to a spatially inhomogeneous magnetic field generated by a nearby nanomagnet. In this paper, we consider such a device and estimate spin-resonator couplings of order ∼1 MHz with realistic parameters. Further, through realistic simulations, we show that precise placement of the double-dot relative to the nanomagnet allows to select between a purely longitudinal coupling (commuting with the bare spin Hamiltonian) and a purely transverse (spin non-conserving) coupling. Additionally, we suggest methods to mitigate dephasing and relaxation channels that are introduced in this coupling scheme. This analysis gives a clear route toward the realization of coherent state transfer between a microwave resonator and a single electron spin in a GaAs double quantum dot with a fidelity above 90%. Improved dynamical decoupling sequences, low-noise environments, and longer-lived microwave cavity modes may lead to substantially higher fidelities in the near future.

arXiv:1606.04736•Nanotechnology•Oct 17, 2016•64 citations

Strong coupling of hybrid system between semiconductor quantum dots and superconducting resonator

Mingbo Chen, Yong-Qiang Xu, Gang Cao +1 more

Quantum computing is a powerful way of improving computing efficiency. For some specific problems, quantum processor can exponentially reduce computation time compared to the classical computer. Cavity quantum electrodynamics, which studies the coherent interaction between photons in an optical cavity and atoms or other two-level systems, is of enormous significance to quantum computing and quantum information processing. The strong coupling regime where a cavity photon mode and an atom exchange a single quantum energy coherently has attracted extensive interest in varied experimental platforms and systems such as alkali atoms, Rydberg atoms, large spin ensembles, magnons, etc. The semiconductor gate-defined double quantum dot (DQD) system is one of the most promising platforms that possesses advantages of advanced micro-nano processing technology and outstanding scalability. Introducing the concept of cavity QED into superconducting circuits (circuit QED, cQED), provides an opportunity to study interaction between electrons confined in semiconductor DQD and photons trapped in a superconducting resonator. Reaching strong coupling regime in this hybrid system paves the way to large-scale network of quantum computing. Electrons confined in DQD have large electrical dipoles, thus are able to couple to photons with relatively large coupling rate. Whereas, due to the charge noise and other dissipation channels in the hybrid system, the decoherence rate of the system is larger than the coupling rate, leaving the strong coupling a great challenge. In recent years, different methods have been proposed to access the strong coupling regime. Taking advantage of a high-quality heterojunction structure, an overlapping gate architecture and a low-pass LC filter on the DC bias line, the decoherence of the charge qubit and microwave leakage of the resonator can be effectively suppressed. The coupling strength of the hybrid system can be improved utilizing a high impedance resonator which is comprised of high kinetic inductance materials. Spin, which does not interact directly with the electric field, is insensitive to charge noise and has much longer decoherence time than charge qubit. However, the weak interaction results in a small coupling rate between the spin and the photon. To solve this problem, the method of coherent hybridization between the spin and the charge state is proposed to improve the coupling strength. This hybridization can be achieved by applying a non-uniform magnetic field, utilizing spin-orbit interaction or spin exchange interaction. At present, both charge qubits and spin qubits have achieved strong coupling with the cavity and the coupling distance between long-range qubits is greatly expanded as long as millimeters. This review introduces basic ideas about cQED and fundamental elements in semiconductor cQED systems. Recent progress in strong coupling hybrid system and methods for improving coupling structures are discussed. In future research, more efforts will be devoted into long-range transfer of qubit states and photon-mediated two or multi-qubit gates.

Chinese Science Bulletin (Chinese Version)•Apr 24, 2020•0 citations

Development of a Silicon Semiconductor Quantum Dot Qubit with Dispersive Microwave Readout

Edward Henry

Semiconductor quantum dots in silicon demonstrate exceptionally long spin lifetimes as qubits and are therefore promising candidates for quantum information processing. However, control and readout techniques for these devices have thus far employed low frequency electrons, in contrast to high speed temperature readout techniques used in other qubit architectures, and coupling between multiple quantum dot qubits has not been satisfactorily addressed.This dissertation presents the design and characterization of a semiconductor charge qubit based on double quantum dot in silicon with an integrated microwave resonator for control and readout. The 6 GHz resonator is designed to achieve strong coupling with the quantum dot qubit, allowing the use of circuit QED control and readout techniques which have not previously been applicable to semiconductor qubits. To achieve this coupling, this document demonstrates successful operation of a novel silicon double quantum dot design with a single active metallic layer and a coplanar stripline resonator with a bias tee for dc excitation.Experiments presented here demonstrate quantum localization and measurement of both electrons on the quantum dot and photons in the resonator. Further, it is shown that the resonator-qubit coupling in these devices is sufficient to reach the strong coupling regime of circuit QED. The details of a measurement setup capable of performing simultaneous low noise measurements of the resonator and quantum dot structure are also presented here.The ultimate aim of this research is to integrate the long coherence times observed in electron spins in silicon with the sophisticated readout architectures available in circuit QED based quantum information systems. This would allow superconducting qubits to be coupled directly to semiconductor qubits to create hybrid quantum systems with separate quantum memory and processing components.

•Jan 1, 2013•0 citations
Strong coupling of semiconductor spin qubits to superconducting microwave resonators was recently demonstrated [X. Mi et al., Nature 555, 599 (2018); A. J. Landig et al., Nature 560, 179 (2018); N. Samkharadze et al., Science 359, 1123 (2018); T. Cubaynes et al., NPJ Quant. Inf. 5, 47 (2019)]. These breakthroughs pave the way for quantum information processing that combines the long coherence times of solid-state spin qubits with the long-distance connectivity, fast control, and fast high-fidelity quantum-non-demolition readout of existing superconducting qubit implementations. Here we theoretically analyze and optimize the dispersive readout of a single spin in a semiconductor double quantum dot (DQD) coupled to a microwave resonator via its electric dipole moment. The strong spin-photon coupling arises from the motion of the electron spin in a local magnetic field gradient. We calculate the signal-to-noise ratio (SNR) of the readout accounting for both Purcell spin relaxation and spin relaxation arising from intrinsic electric noise within the semiconductor. We express the maximum achievable SNR in terms of the cooperativity associated with these two dissipation processes. We find that while the cooperativity increases with the strength of the dipole coupling between the DQD and the resonator, it does not depend on the strength of the magnetic field gradient. We then optimize the SNR as a function of experimentally tunable DQD parameters. We identify wide regions of parameter space where the unwanted backaction of the resonator photons on the qubit is small. Moreover, we find that the coupling of the resonator to other DQD transitions can enhance the SNR by at least a factor of two, a ``straddling'' effect [J. Koch et al., Phys. Rev. A 76, 042319 (2007)] that occurs only at nonzero energy detuning of the DQD double-well potential. We estimate that with current technology, single-shot readout fidelities in the range 82--95% can be achieved within a few \ensuremathμs\ensuremath{\mu}\mathrm{s}\ensuremathμs of readout time without requiring the use of Purcell filters.
Superconducting resonators coupled to solid-state qubits offer a scalable architecture for long-range entangling operations and fast, high-fidelity readout. Realizing this requires low photon-loss rates and qubits with tunable electric dipole moments that couple strongly to the resonator's electric field while maintaining long coherence times. For spin qubits, spin-photon coupling is typically achieved via spin-charge hybridization. However, this introduces a fundamental trade-off: a large spin-charge admixture enhances the coupling strength, which boosts readout and resonator-mediated gate speeds, but exposes the qubit to increased decoherence, thereby increasing the threshold required for strong coupling and limiting the time available for accurate state measurement. This makes it essential to identify optimal operating points for each qubit platform. We address this for the donor-based flip-flop qubit, whose microwave-controllable electron-nuclear spin states make it suitable for coupling to microwave resonators. We demonstrate that, by choosing intermediate tunnel couplings that balance strong interaction with long qubit lifetimes, high-fidelity readout and strong coupling are simultaneously achievable. We also map out the respective charge-photon couplings and photon-loss rates required. Furthermore, we show that experimental constraints on charge-photon coupling and photon loss can be mitigated using squeezed input fields. As similar trade-offs appear in quantum-dot-based qubits, our methods and insights extend naturally to these platforms, offering a potential route toward scalable architectures.
Fast and high-fidelity qubit measurement is essential for quantum error correction in universal quantum computing. This study examines dispersive measurement of a spin in a semiconductor double quantum dot using a nonlinear microwave resonator. By employing displaced squeezed vacuum states, we achieve rapid, high-fidelity readout for silicon spin qubits. Our results show that modest squeezing and mild nonlinearity significantly enhance the signal-to-noise ratio (SNR) and the fidelity of qubit-state readout. By optimally adjusting the phases of squeezing and nonlinearity, we reduce readout time to sub-microsecond ranges. With current technology parameters ( κ ≈ 2 χ s , χ s /(2 π ) ≈ 0.15 MHz), utilizing a displaced squeezed vacuum state with 30 photons and a modest squeezing parameter r ≈ 0.6, along with a nonlinear microwave resonator charactered by a strength of λ ≈ − 1.2 χ s , a readout fidelity of 98% can be attained within a readout time of around 0.6 μ s.
The performance of a wide range of quantum computing algorithms and protocols depends critically on the fidelity and speed of the employed qubit readout. Examples include gate sequences benefiting from midcircuit real-time measurement-based feedback, such as qubit initialization, entanglement generation, teleportation, and, perhaps most importantly, quantum error correction. A prominent and widely used readout approach is based on the dispersive interaction of a superconducting qubit strongly coupled to a large-bandwidth readout resonator, frequently combined with a dedicated or shared Purcell filter protecting qubits from decay. By dynamically reducing the qubit-resonator detuning and thus increasing the dispersive shift, we demonstrate a beyond-state-of-the-art two-state-readout error of only 0.25% in 100-ns integration time. Maintaining low-readout-drive strength, we nearly quadruple the signal-to-noise ratio of the readout by doubling the readout-mode line width, which we quantify by considering the hybridization of the readout resonator and its dedicated Purcell filter. We find excellent agreement between our experimental data and our theoretical model. The presented results are expected to further boost the performance of new and existing algorithms and protocols critically depending on high-fidelity fast midcircuit measurements. Published by the American Physical Society 2024
Microwave-frequency superconducting resonators are ideally suited to perform dispersive qubit readout, to mediate two-qubit gates, and to shuttle states between distant quantum systems. A prerequisite for these applications is a strong qubit-resonator coupling. Strong coupling between an electron-spin qubit and a microwave resonator can be achieved by correlating spin- and orbital degrees of freedom. This correlation can be achieved through the Zeeman coupling of a single electron in a double quantum dot to a spatially inhomogeneous magnetic field generated by a nearby nanomagnet. In this paper, we consider such a device and estimate spin-resonator couplings of order ∼1 MHz with realistic parameters. Further, through realistic simulations, we show that precise placement of the double-dot relative to the nanomagnet allows to select between a purely longitudinal coupling (commuting with the bare spin Hamiltonian) and a purely transverse (spin non-conserving) coupling. Additionally, we suggest methods to mitigate dephasing and relaxation channels that are introduced in this coupling scheme. This analysis gives a clear route toward the realization of coherent state transfer between a microwave resonator and a single electron spin in a GaAs double quantum dot with a fidelity above 90%. Improved dynamical decoupling sequences, low-noise environments, and longer-lived microwave cavity modes may lead to substantially higher fidelities in the near future.
Quantum computing is a powerful way of improving computing efficiency. For some specific problems, quantum processor can exponentially reduce computation time compared to the classical computer. Cavity quantum electrodynamics, which studies the coherent interaction between photons in an optical cavity and atoms or other two-level systems, is of enormous significance to quantum computing and quantum information processing. The strong coupling regime where a cavity photon mode and an atom exchange a single quantum energy coherently has attracted extensive interest in varied experimental platforms and systems such as alkali atoms, Rydberg atoms, large spin ensembles, magnons, etc. The semiconductor gate-defined double quantum dot (DQD) system is one of the most promising platforms that possesses advantages of advanced micro-nano processing technology and outstanding scalability. Introducing the concept of cavity QED into superconducting circuits (circuit QED, cQED), provides an opportunity to study interaction between electrons confined in semiconductor DQD and photons trapped in a superconducting resonator. Reaching strong coupling regime in this hybrid system paves the way to large-scale network of quantum computing. Electrons confined in DQD have large electrical dipoles, thus are able to couple to photons with relatively large coupling rate. Whereas, due to the charge noise and other dissipation channels in the hybrid system, the decoherence rate of the system is larger than the coupling rate, leaving the strong coupling a great challenge. In recent years, different methods have been proposed to access the strong coupling regime. Taking advantage of a high-quality heterojunction structure, an overlapping gate architecture and a low-pass LC filter on the DC bias line, the decoherence of the charge qubit and microwave leakage of the resonator can be effectively suppressed. The coupling strength of the hybrid system can be improved utilizing a high impedance resonator which is comprised of high kinetic inductance materials. Spin, which does not interact directly with the electric field, is insensitive to charge noise and has much longer decoherence time than charge qubit. However, the weak interaction results in a small coupling rate between the spin and the photon. To solve this problem, the method of coherent hybridization between the spin and the charge state is proposed to improve the coupling strength. This hybridization can be achieved by applying a non-uniform magnetic field, utilizing spin-orbit interaction or spin exchange interaction. At present, both charge qubits and spin qubits have achieved strong coupling with the cavity and the coupling distance between long-range qubits is greatly expanded as long as millimeters. This review introduces basic ideas about cQED and fundamental elements in semiconductor cQED systems. Recent progress in strong coupling hybrid system and methods for improving coupling structures are discussed. In future research, more efforts will be devoted into long-range transfer of qubit states and photon-mediated two or multi-qubit gates.
Semiconductor quantum dots in silicon demonstrate exceptionally long spin lifetimes as qubits and are therefore promising candidates for quantum information processing. However, control and readout techniques for these devices have thus far employed low frequency electrons, in contrast to high speed temperature readout techniques used in other qubit architectures, and coupling between multiple quantum dot qubits has not been satisfactorily addressed.This dissertation presents the design and characterization of a semiconductor charge qubit based on double quantum dot in silicon with an integrated microwave resonator for control and readout. The 6 GHz resonator is designed to achieve strong coupling with the quantum dot qubit, allowing the use of circuit QED control and readout techniques which have not previously been applicable to semiconductor qubits. To achieve this coupling, this document demonstrates successful operation of a novel silicon double quantum dot design with a single active metallic layer and a coplanar stripline resonator with a bias tee for dc excitation.Experiments presented here demonstrate quantum localization and measurement of both electrons on the quantum dot and photons in the resonator. Further, it is shown that the resonator-qubit coupling in these devices is sufficient to reach the strong coupling regime of circuit QED. The details of a measurement setup capable of performing simultaneous low noise measurements of the resonator and quantum dot structure are also presented here.The ultimate aim of this research is to integrate the long coherence times observed in electron spins in silicon with the sophisticated readout architectures available in circuit QED based quantum information systems. This would allow superconducting qubits to be coupled directly to semiconductor qubits to create hybrid quantum systems with separate quantum memory and processing components.