Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2508.04007 · Nano Letters

Transmon Qubit Using Sn as a Junction Superconductor

Amrita Purkayastha, Amritesh Sharma, Param J. Patel, An‐Hsi Chen, Connor P. Dempsey, Shreyas Asodekar, Subhayan Sinha, Maxime Tomasian, Mihir Pendharkar, Christopher J. Palmstrøm, Moïra Hocevar, Kun Zuo, Michael J. Hatridge, Sergey Frolov

Published Feb 9, 2026• 4 citations
arXivHTMLPDF

Abstract

Superconductor qubits typically use aluminum–aluminum oxide tunnel junctions to provide the nonlinear inductance. Junctions with semiconductor barriers make it possible to vary the superconductor material and explore beyond aluminum. We use InAs semiconductor nanowires coated with thin superconducting shells of β-Sn to realize transmon qubits. By tuning the Josephson energy with a gate voltage, we adjust the qubit frequency over a range of 3 GHz. The longest energy relaxation time, T 1 = 27 μs, is obtained at the lowest qubit frequencies, while the longest echo dephasing time, T 2 = 1.8 μs, is achieved at higher frequencies. We assess the possible factors limiting coherence times in these devices and discuss steps to enhance performance through improvements in materials fabrication and circuit design.

DOI
10.1021/acs.nanolett.5c05276

Related papers

Tunable anharmonicity in Sn-InAs nanowire transmons beyond the short junction limit

Amrita Purkayastha, Amritesh Sharma, Param J. Patel +11 more

The anharmonicity of a transmon qubit, defined as the difference in energy level spacing, is a key design parameter. In transmons built from hybrid superconductor-semiconductor Josephson elements, the anharmonicity is tunable with gate voltages that control both the Josephson energy and the weak link transparency. In Sn-InAs nanowire transmons, we use two-tone microwave spectroscopy to extract anharmonicity ranging in absolute value from the transmon charging energy $E_c$ to values smaller than $E_c/10$. This behavior contrasts with the predictions of the multi-channel short-junction model, which sets a lower limit on anharmonicity at $E_c/4$. Coherent operation of the qubit is still possible at the point of the lowest anharmonicity. These findings demonstrate the potential of quantum circuits that benefit from widely electrically tunable anharmonicity.

cond-mat.mes-hallCross-listedarXiv:2603.26895•Mar 31, 2026•2 citations

Methods to achieve near-millisecond energy relaxation and dephasing times for a superconducting transmon qubit

Mikko Tuokkola, Yoshiki Sunada, Heidi Kivijärvi +6 more

Abstract Superconducting qubits are one of the most promising physical systems for implementing quantum computers. However, executing quantum algorithms of practical computational advantage requires further improvements in the fidelities of qubit operations, which are currently limited by the energy relaxation and dephasing times of the qubits. Here, we report our measurement results of a high-coherence transmon qubit with energy relaxation and echo dephasing times surpassing those in the existing literature. We measure a qubit frequency of 2.9 GHz, an energy relaxation time T 1 with a median of 425 μs and a maximum of (666 ± 33)μs, and an echo dephasing time $${T}_{2}^{{{{\rm{echo}}}}}$$ T 2 echo with a median of 541 μs and a maximum of (1057 ± 138)μs. We report in detail our design, fabrication process, and measurement setup to facilitate the reproduction and wide adoption of high-coherence transmon qubits in the academia and industry.

arXiv:2407.18778•Nature Communications•Jul 8, 2025•98 citations

A transmon qubit realized by exploiting the superconductor-insulator transition

C. G. L. Bøttcher, D. Ekin Önder, Thomas Connolly +8 more

Superconducting qubits are among the most promising platforms for realizing practical quantum computers. One requirement to create a quantum processor is nonlinearity, which in superconducting circuits is typically achieved by sandwiching a layer of aluminum oxide between two aluminum electrodes to form a Josephson junction. These junctions, however, face several limitations that hinder their scalability: the small superconducting gap of aluminum necessitates millikelvin operating temperatures, the material interfaces lead to dissipation, and the sandwich geometry adds unwelcome capacitance for high-frequency applications. In this work, we address all three limitations using a novel superconducting weak link based on the superconductor-insulator transition. By locally thinning a single film of niobium nitride, we exploit its thickness-driven superconductor-insulator transition to form a weak link employing only atomic layer deposition and atomic layer etching. We utilize our weak links to produce a transmon qubit, '$planaron$', with a measured anharmonicity of $α/2π= 235$ MHz; at present, the linewidth is $κ/2π= 15 \mathrm{\: MHz}$. The high superconducting gap of niobium nitride can enable operation at elevated temperatures in future devices, and the fully planar geometry of the weak link eliminates superfluous material interfaces and capacitances. The investigation of small patches of material near the SIT can shed new light on the nature of the transition, including the role of dissipation and finite-size effects.

arXiv:2510.19983•Oct 22, 2025•8 citations

Circuit Quantum Electrodynamics in a Magnetic Field

Florian Luthi

Quantum computers promise to solve certain problems such as quantum chemistry simulations much more efficiently than their classical counterparts. Although it is still unclear what material system will ultimately host large-scale quantum computers, solid-state systems are promising candidates due to their inherent scalability and advanced fabrication techniques that can be adapted from comparable technologies. Crucially, a future quantum computer will depend on the quality of its most fundamental building block, the quantum bit, or qubit. Qubits, although ideally insensitive to potential noise, are very susceptible to slight changes in their environment. Therefore, they do not only make the building block for quantum computers, but are also precise sensors. One of the most studied solid-state implementations of a qubit is the transmon, a weakly anharmonic oscillator based on superconducting capacitive and nonlinear inductive elements. Typically, Al-AlOx-Al superconductor-insulator-superconductor Josephson junctions are used for the latter. The interaction of the transmon with the control circuitry, typically superconducting resonators, is described by circuit quantum electrodynamics. In this PhD thesis, a more recently demonstrated type of qubit is further developed and studied in detail using circuit quantum electrodynamics. In these qubits, the Josephson element of the transmon is replaced with indium arsenide nanowires, forming a superconductor-normal metalsuperconductor junction. In addition to the standard flux tunability, these qubits can also be voltage tuned. Due to the compatibility of all the materials used with an applied magnetic field, this type of qubit is a good candidate to be used as a precise and accurate sensor in a magnetic field. The goal of this work is to introduce the in-plane magnetic field as a new tuning knob to the toolbox of circuit quantum electrodynamics. Advances in material science, especially the epitaxial growth of an aluminum shell directly on the indium arsenide nanowire, have enabled the fabrication of nanowire transmons with state-of-the-art coherence. An understanding of their workings in a zero-field environment is important before applying a magnetic field. Thus, we characterize the noise these qubits are subject to (Chapter 4) and find a strong coupling of charge two-level systems to their Josephson energy next to the expected weakly coupled flux and voltage noise. Applying a magnetic field reveals that coherence in these qubits can be observed up to 70 mT, substantially above the superconducting gap of bulk aluminum (Chapter 5). Effects limiting the performance include the thick and fully covering aluminum shell, and the alignment and stability of the magnetic field. The use of different nanowires, the installation of a persistent-current vector solenoid and additional magnetic shielding then enables the operation of voltage- and flux-tunable devices in a magnetic field (Chapter 6). This constitutes a good starting point for circuit quantum electrodynamics experiments in a magnetic field, such as the investigation of the microscopic origin of flux-noise.

•Mar 8, 2019•0 citations

Hole-type superconducting gatemon qubit based on Ge/Si core/shell nanowires

Enna Zhuo, Zhaozheng Lyu, Xiaopei Sun +11 more

Abstract We demonstrate that superconducting gatemon qubits based on superconductor-semiconductor-superconductor Josephson junctions can be constructed on hole-type Ge/Si core/shell nanowires. The frequency of the qubit can be set firstly by controlling the diffusion of Al in the nanowire via thermal annealing, which yields a suitable critical supercurrent allowing the qubit frequency to be within the experimentally accessible range, and then by fine tuning of a gate voltage, by which an accurate adjustment of the frequency can be realized. On the resulted qubit, Rabi oscillation with an energy relaxation time $${T}_{1} \sim 180\,{\rm{ns}}$$ T 1 ~ 180 ns was observed in the time domain, an average decoherence time $${T}_{2}^{* } \sim 15\,{\rm{ns}}$$ T 2 * ~ 15 ns was obtained, and the gate voltage dependence of both $${T}_{1}$$ T 1 and $${T}_{2}^{* }$$ T 2 * was investigated. Such a hole-type superconducting gatemon qubit, based on materials with strong spin-orbit coupling and potentially the absence of hyperfine interaction after isotope purification, could be used for exploring the quantum coherence phenomena of hole-gas and even Majorana physics in Ge-based quantum devices.

npj Quantum Information•May 31, 2023•37 citations

Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits

Amr Osman, J. Simon, Andreas Bengtsson +7 more

We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.

arXiv:2011.05230•Applied Physics Letters•Feb 8, 2021•104 citations
Superconductor qubits typically use aluminum–aluminum oxide tunnel junctions to provide the nonlinear inductance. Junctions with semiconductor barriers make it possible to vary the superconductor material and explore beyond aluminum. We use InAs semiconductor nanowires coated with thin superconducting shells of β-Sn to realize transmon qubits. By tuning the Josephson energy with a gate voltage, we adjust the qubit frequency over a range of 3 GHz. The longest energy relaxation time, T 1 = 27 μs, is obtained at the lowest qubit frequencies, while the longest echo dephasing time, T 2 = 1.8 μs, is achieved at higher frequencies. We assess the possible factors limiting coherence times in these devices and discuss steps to enhance performance through improvements in materials fabrication and circuit design.
The anharmonicity of a transmon qubit, defined as the difference in energy level spacing, is a key design parameter. In transmons built from hybrid superconductor-semiconductor Josephson elements, the anharmonicity is tunable with gate voltages that control both the Josephson energy and the weak link transparency. In Sn-InAs nanowire transmons, we use two-tone microwave spectroscopy to extract anharmonicity ranging in absolute value from the transmon charging energy EcE_cEc​ to values smaller than Ec/10E_c/10Ec​/10. This behavior contrasts with the predictions of the multi-channel short-junction model, which sets a lower limit on anharmonicity at Ec/4E_c/4Ec​/4. Coherent operation of the qubit is still possible at the point of the lowest anharmonicity. These findings demonstrate the potential of quantum circuits that benefit from widely electrically tunable anharmonicity.
Abstract Superconducting qubits are one of the most promising physical systems for implementing quantum computers. However, executing quantum algorithms of practical computational advantage requires further improvements in the fidelities of qubit operations, which are currently limited by the energy relaxation and dephasing times of the qubits. Here, we report our measurement results of a high-coherence transmon qubit with energy relaxation and echo dephasing times surpassing those in the existing literature. We measure a qubit frequency of 2.9 GHz, an energy relaxation time T 1 with a median of 425 μs and a maximum of (666 ± 33)μs, and an echo dephasing time T2echo{T}_{2}^{{{{\rm{echo}}}}}T2echo​ T 2 echo with a median of 541 μs and a maximum of (1057 ± 138)μs. We report in detail our design, fabrication process, and measurement setup to facilitate the reproduction and wide adoption of high-coherence transmon qubits in the academia and industry.
Superconducting qubits are among the most promising platforms for realizing practical quantum computers. One requirement to create a quantum processor is nonlinearity, which in superconducting circuits is typically achieved by sandwiching a layer of aluminum oxide between two aluminum electrodes to form a Josephson junction. These junctions, however, face several limitations that hinder their scalability: the small superconducting gap of aluminum necessitates millikelvin operating temperatures, the material interfaces lead to dissipation, and the sandwich geometry adds unwelcome capacitance for high-frequency applications. In this work, we address all three limitations using a novel superconducting weak link based on the superconductor-insulator transition. By locally thinning a single film of niobium nitride, we exploit its thickness-driven superconductor-insulator transition to form a weak link employing only atomic layer deposition and atomic layer etching. We utilize our weak links to produce a transmon qubit, 'planaronplanaronplanaron', with a measured anharmonicity of α/2π=235α/2π= 235α/2π=235 MHz; at present, the linewidth is κ/2π=15 MHzκ/2π= 15 \mathrm{\: MHz}κ/2π=15MHz. The high superconducting gap of niobium nitride can enable operation at elevated temperatures in future devices, and the fully planar geometry of the weak link eliminates superfluous material interfaces and capacitances. The investigation of small patches of material near the SIT can shed new light on the nature of the transition, including the role of dissipation and finite-size effects.
Quantum computers promise to solve certain problems such as quantum chemistry simulations much more efficiently than their classical counterparts. Although it is still unclear what material system will ultimately host large-scale quantum computers, solid-state systems are promising candidates due to their inherent scalability and advanced fabrication techniques that can be adapted from comparable technologies. Crucially, a future quantum computer will depend on the quality of its most fundamental building block, the quantum bit, or qubit. Qubits, although ideally insensitive to potential noise, are very susceptible to slight changes in their environment. Therefore, they do not only make the building block for quantum computers, but are also precise sensors. One of the most studied solid-state implementations of a qubit is the transmon, a weakly anharmonic oscillator based on superconducting capacitive and nonlinear inductive elements. Typically, Al-AlOx-Al superconductor-insulator-superconductor Josephson junctions are used for the latter. The interaction of the transmon with the control circuitry, typically superconducting resonators, is described by circuit quantum electrodynamics. In this PhD thesis, a more recently demonstrated type of qubit is further developed and studied in detail using circuit quantum electrodynamics. In these qubits, the Josephson element of the transmon is replaced with indium arsenide nanowires, forming a superconductor-normal metalsuperconductor junction. In addition to the standard flux tunability, these qubits can also be voltage tuned. Due to the compatibility of all the materials used with an applied magnetic field, this type of qubit is a good candidate to be used as a precise and accurate sensor in a magnetic field. The goal of this work is to introduce the in-plane magnetic field as a new tuning knob to the toolbox of circuit quantum electrodynamics. Advances in material science, especially the epitaxial growth of an aluminum shell directly on the indium arsenide nanowire, have enabled the fabrication of nanowire transmons with state-of-the-art coherence. An understanding of their workings in a zero-field environment is important before applying a magnetic field. Thus, we characterize the noise these qubits are subject to (Chapter 4) and find a strong coupling of charge two-level systems to their Josephson energy next to the expected weakly coupled flux and voltage noise. Applying a magnetic field reveals that coherence in these qubits can be observed up to 70 mT, substantially above the superconducting gap of bulk aluminum (Chapter 5). Effects limiting the performance include the thick and fully covering aluminum shell, and the alignment and stability of the magnetic field. The use of different nanowires, the installation of a persistent-current vector solenoid and additional magnetic shielding then enables the operation of voltage- and flux-tunable devices in a magnetic field (Chapter 6). This constitutes a good starting point for circuit quantum electrodynamics experiments in a magnetic field, such as the investigation of the microscopic origin of flux-noise.
Abstract We demonstrate that superconducting gatemon qubits based on superconductor-semiconductor-superconductor Josephson junctions can be constructed on hole-type Ge/Si core/shell nanowires. The frequency of the qubit can be set firstly by controlling the diffusion of Al in the nanowire via thermal annealing, which yields a suitable critical supercurrent allowing the qubit frequency to be within the experimentally accessible range, and then by fine tuning of a gate voltage, by which an accurate adjustment of the frequency can be realized. On the resulted qubit, Rabi oscillation with an energy relaxation time T1∼180 ns{T}_{1} \sim 180\,{\rm{ns}}T1​∼180ns T 1 ~ 180 ns was observed in the time domain, an average decoherence time T2∗∼15 ns{T}_{2}^{* } \sim 15\,{\rm{ns}}T2∗​∼15ns T 2 * ~ 15 ns was obtained, and the gate voltage dependence of both T1{T}_{1}T1​ T 1 and T2∗{T}_{2}^{* }T2∗​ T 2 * was investigated. Such a hole-type superconducting gatemon qubit, based on materials with strong spin-orbit coupling and potentially the absence of hyperfine interaction after isotope purification, could be used for exploring the quantum coherence phenomena of hole-gas and even Majorana physics in Ge-based quantum devices.
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.