The auto-correlative weak-value amplification (AWVA) technique demonstrates distinct advantages over standard weak-value amplification (SWVA) for quantum parameter estimation. To achieve enhanced precision in real-time parameter estimation, the AWVA requires additional resources compared to SWVA, namely real-time multiplication and integrator modules. We implemented a real-time analog circuit for AWVA using an AD835 multiplier and an NE5532 operational amplifier for the integrator. The circuit was tested using Gaussian pointers in the AWVA scheme, exhibiting sufficient sensitivity for Gaussian pointers with frequencies 200 Hz ≤ f ≤ 20 kHz. Compared to SWVA, AWVA achieves higher accuracy and superior robustness against noise at signal-to-noise ratios (SNRs) of −12 dB ≤ SNR ≤ −4 dB. Beyond quantum metrology, the circuit is applicable to diverse detection schemes for correlated signals.
The auto-correlative weak-value amplification (AWVA) technique demonstrates distinct advantages over standard weak-value amplification (SWVA) for quantum parameter estimation. To achieve enhanced precision in real-time parameter estimation, the AWVA requires additional resources compared to SWVA, namely real-time multiplication and integrator modules. We implemented a real-time analog circuit for AWVA using an AD835 multiplier and an NE5532 operational amplifier for the integrator. The circuit was tested using Gaussian pointers in the AWVA scheme, exhibiting sufficient sensitivity for Gaussian pointers with frequencies 200 Hz ≤ f ≤ 20 kHz. Compared to SWVA, AWVA achieves higher accuracy and superior robustness against noise at signal-to-noise ratios (SNRs) of −12 dB ≤ SNR ≤ −4 dB. Beyond quantum metrology, the circuit is applicable to diverse detection schemes for correlated signals.
By choosing more orthogonality between preselection and postselection states, one can significantly improve the sensitivity in general optical quantum metrology based on the weak-value amplification (WVA) approach. However, increasing the orthogonality decreases the probability of detecting photons and makes the weak measurement difficult, especially when the weak measurement is disturbed by strong noise and the pointer is drowned in noise with a negative-decibel signal-to-noise ratio (SNR). In this article we introduce and numerically evaluate a modified weak-measurement protocol with a temporal pointer, namely, the autocorrelative weak-value amplification (AWVA) approach. Specifically, a small longitudinal time delay (tiny phase shift) $\ensuremath{\tau}$ of a Gaussian pulse is measured by implementing two simultaneous autocorrelative weak measurements under Gaussian white noise with different SNRs. The small quantities $\ensuremath{\tau}$ are obtained by measuring the autocorrelation coefficient of the pulses instead of fitting the shift of the mean value of the probe in the standard WVA technique. Simulation results show that the AWVA approach outperforms the standard WVA technique in the time domain with smaller statistical errors, remarkably increasing the precision of weak measurement under a strong noise background.
Weak-value amplification (WVA), a postselection-based technique that amplifies weak physical signals by preparing nearly orthogonal pre- and postselected quantum states, is intrinsically limited by various kinds of technical noise, which distorts amplified weak values, especially when discarding photons in postselection. While prior work established the efficacy of autocorrelative weak-value amplification (AWVA) under Gaussian noise, practical implementations face challenges from band-limited laser-source noise and detection noise (including shot noise and electrical noise). Here, we demonstrate that the AWVA protocol robustly suppresses both laser-power fluctuations and detection noise. Numerical experiments in Simulink further reveal AWVA's dual advantage: under high-power conditions, the noise-reduction superiority of AWVA over WVA becomes in- creasingly pronounced as input laser power increases, whereas in detection-limited regimes AWVA achieves an order-of-magnitude lower uncertainty, closely approaching the Cram\'er-Rao bound. Crucially, this work demonstrates that AWVA improves precision in both high-power (laser-noise-dominated) and photon-starved (detector-noise-dominated) regimes, thereby bridging these operating extremes and advancing precision in applications from gravitational-wave detection to hybrid quantum systems.
Weak-value amplification (WVA) has recently become an important technique for parameter estimation, owing to its ability to enhance the signal-to-noise ratio by amplifying extremely small signals with proper postselection strategies. In this paper, we propose an adaptive WVA scheme to achieve the highest Fisher information when using an unbalanced pointer. Different from previous schemes, the adaptive WVA scheme is associated with a real-time update on the postselection states with the help of feedback information from the outcomes, and the ``extremely small'' condition set on the parameter of interest is relaxed. By applying this scheme to a time-delay measurement scenario, we show by numerical simulation that the precision achieved in our scheme is several times higher than the standard WVA scheme. Our result might open a path for improving the WVA technique in a more flexible and robust way.
Precision measurements are bounded by the Standard Quantum Limit, and prepar- ing non-classical states is often used to circumvent such a limit. In all cases, it is common to improve the precision in a parameter estimation procedure by averaging measurements of a large ensemble of identically prepared systems. However, such a task cannot be performed indefinitely due to sources of technical noise setting an experimental bound. Weak-Value Amplification (WVA) allows one to overcome some of these issues by amplifying a signal of interest above the technical-noise floor. This built-in robustness to external sources of noise relies on a weak coupling to a meter and postselection. In this document we evaluate, the- oretically and experimentally, under what circumstances the technique is superior to non-postselected standard techniques. We also present a novel protocol where a WVA-like response is induced in an optical homodyne-type detection technique. We dub this technique Almost-Balanced Weak Values (ABWV) and present three experimental measurements of different physical velocities to evaluate the practi- cal advantages over the well-known technique of WVA. In addition, we point out the existence of a third postselected-weak-measurements technique for metrology, Inverse Weak Value (IWV), that has been ignored by the scientific community. We use this protocol to measure ultra small tilts of a mirror in a Sagnac interfer- ometer. We report all three techniques as complementary to each other, and show their robustness for low-frequency signals.
The weak-value amplification is extensively considered in precision metrology in order to achieve a higher sensitivity. Despite the practical benefits in amplifying small physical quantities, its metrological advantage still arouses a broad debate due to the low postselection probability of success. In this paper, by employing the quantum Fisher information metric, we show that the precision of estimating an unknown parameter can be improved by introducing a precoupling process with properly chosen interaction operators. We point out this result is credible for both real and imaginary weak values. By tracking the meter wave functions, we find this enhancement of estimation precision comes from a precoupling induced modulation of the meter wave function, thus the most sensitive regime with respect to the parameter is reached. In addition, the estimation error is investigated by considering the difference between the theoretical and estimated value. The analysis suggests that this kind of error can be effectively suppressed by averaging the estimations resulted from different initial meter states. These results are finally illustrated by an exact numerical simulation where the advantages of our proposal are displayed by the comparison to the standard weak-value amplification scheme.
Abstract Reducing noises and enhancing signal-to-noise ratios (SNRs) have become critical for designing third-generation gravitational-wave (GW) detectors with a GW strain of less than 10 − 23 H z − 1 . In this paper, we propose a potential third-generation GW detector based on autocorrelative weak-value amplification (AWVA) for GW detection with a strain of h g = 4 × 10 − 25 H z − 1 . In our scheme, a GW event induces a phase difference Δ ϕ by passing through a 11-bounce delay line, 10-km arm-length, zero-area Sagnac interferometer illuminated with a 1064-nm laser. Subsequently, Δ ϕ is amplified as the parameter of post-selection by choosing the appropriate pre-selected state and coupling strength in AWVA. In particular, we theoretically investigate the AWVA measurements for GW detection within the frequency band of 200 Hz ⩽ f g ⩽ 800 Hz, considering Gaussian noises with negative-decibel SNRs. The peak response of the AWVA sensitivity κ ( f g ) occurs at frequency f g , m a x = 500 Hz, which falls within the frequency band of interest of the current third-generation GW detectors. Our simulation results indicate that AWVA can demonstrate a measurable sensitivity of the autocorrelation coefficient Θ ( f g ) within the frequency band of interest. Moreover, the robustness of WVA shows promising potential in mitigating the effects of Gaussian noises.