Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2507.18027 · Carbon

Nitrogen-vacancy centre formation via local femto-second laser annealing of diamond

Davin Yue Ming Peng, Alexander J. Healey, Rebecca Griffin, Benjamin P. Cumming, Hiroshi Abe, Takeshi Ohshima, Alastair D. Stacey, Brant C. Gibson, Brett C. Johnson, Philipp Reineck

Published Sep 30, 2025• 4 citations
arXivHTMLPDF

Abstract

Emerging quantum technologies based on the nitrogen-vacancy (NV) centre in diamond require carefully engineered material with controlled defect density, optimised NV formation processes, and minimal crystal strain. The choice of NV generation technique plays a crucial role in determining the quality and performance of these centres. In this work, we investigate NV centre formation in nitrogen-doped diamond using femtosecond (fs) laser processing. We systematically examine the effect of laser pulse energy on NV production and quality using photoluminescence and optically detected magnetic resonance measurements. We also probe the role of pre-existing lattice defects formed by electron irradiation and consider defect evolution over extended dwell times. Finally, we are able to identify a regime where the main action of the fs-laser is to diffuse rather than create vacancies. This local annealing capability expands the toolkit for tailored NV production and presents opportunities for fine tuning defect populations.

DOI
10.1016/j.carbon.2025.120892

Related papers

Direct writing of high-density nitrogen-vacancy centers inside diamond by femtosecond laser irradiation

Torataro Kurita, Yasuhiko Shimotsuma, Masanori Fujiwara +4 more

High-density nitrogen-vacancy (NV) centers exceeding 1016/cm3 inside a diamond can be achieved by femtosecond laser irradiation. The number of pulses and pulse energy were adjusted considering the increasing trend of the NV concentration and damage generation. The NV concentration first grew as the number of laser pulses was increased, and then the concentration was temporarily saturated or decreased. By increasing the number of laser pulses more than 2.5–5 × 107, the concentration increased again. The Hahn-echo measurement revealed that electron spins of the substitutional nitrogen center (P1) were dominant source for decoherence and the number of paramagnetic defects induced by the laser irradiation was not significant for degradation of spin coherence of the laser-induced NV centers even without a post-annealing process. Such high-dense ensemble NV centers are crucial for a high-sensitive quantum sensor.

Applied Physics Letters•May 24, 2021•32 citations

Laser engineering of defects in diamond for quantum technologies

Benjamin Griffiths

Colour centre defects in diamond are promising candidates for many quantum technologies because they act as isolated two level systems in the solid-state that can be controlled and read-out through photonics [1][2][3]. Realisation of these technologies requires the placement of many highly coherent centres in a regular array with high positional accuracy and high fabrication yield [4]. Previous fabrication techniques have lacked the ability to produce high yields with high positional accuracy without causing irreparable damage to the lattice which reduced the quality of the spin and optical properties [5]. Ultra-fast laser writing has been shown to produce highly coherent nitrogen vacancy (NV) colour centres within the diamond lattice with positional accuracies of order hundreds of nanometers and a stochastic yield. In this case, the yield and positional accuracy is held back by the need to thermally anneal the diamond within a furnace to convert laser generated defects into colour centres; a fabrication step in which there is little to no control over individual site [6]. In this thesis, the ultra-fast pulsed laser writing technique is broached in detail from both a theoretical and experimental standpoint. The theory behind the highly non-linear light-matter interactions is studied and a hypothesis is developed for the energy transfer between photo-excited carriers and the lattice via the non-radiative recombination of self-trapped multi-excitonic states [7]. In addition, this thesis presents an expansion on the laser writing of colour centres through broaching the generation of different colour centres that have some preferential properties over the NV [8], and the development of a new engineering technique involving a local laser anneal [9]. The yield of generated centres is increased from stochastic to deterministic by replacing the global thermal anneal with the local laser anneal in combination with a fluorescence feedback mechanism. In addition, the use of the laser to locally anneal generated centres leads to a factor of five improvement in the positional accuracy due to the highly non-linear interaction of the laser with the material. These results culminate in a key step forward in the development of a large scale quantum device and improved understanding of the highly dynamical processes that occur upon femtosecond laser interaction with a wide bandgap material.

•Jan 1, 2021•0 citations

Creation of nitrogen-vacancy centers in chemical vapor deposition diamond for sensing applications

Tingpeng Luo, Lukas Lindner, J Langer +13 more

Abstract The nitrogen-vacancy (NV) center in diamond is a promising quantum system for magnetometry applications exhibiting optical readout of minute energy shifts in its spin sub-levels. Key material requirements for NV ensembles are a high NV − concentration, a long spin coherence time and a stable charge state. However, these are interdependent and can be difficult to optimize during diamond growth and subsequent NV creation. In this work, we systematically investigate the NV center formation and properties in bulk chemical vapor deposition (CVD) diamond. The nitrogen flow during growth is varied by over four orders of magnitude, resulting in a broad range of single substitutional nitrogen concentrations of 0.2–20 parts per million. For a fixed nitrogen concentration, we optimize electron-irradiation fluences with two different accelerated electron energies, and we study defect formation via optical characterizations. We discuss a general approach to determine the optimal irradiation conditions, for which an enhanced NV concentration and an optimum of NV charge states can both be satisfied. We achieve spin–spin coherence times T 2 ranging from 45.5 to 549 μ s for CVD diamonds containing 168 to 1 parts per billion NV − centers, respectively. This study shows a pathway to engineer properties of NV-doped CVD diamonds for improved sensitivity.

arXiv:2111.07981•New Journal of Physics•Feb 25, 2022•87 citations

Nitrogen-vacancy centers in diamond: discovery of additional electronic states

Minh Tuan Luu, Ali Tayefeh Younesi, Ronald Ulbricht

Abstract Nitrogen-vacancy (NV) defect centers in diamond are key to applications in quantum sensing and quantum computing. They create localized electronic states in the diamond lattice with distinct population relaxation pathways following photoexcitation that ultimately enable its unique properties. The defect is known to exist in two charge states: neutral and negative, with respectively one and two known optically-active electronic transitions. Here, we report on the observation of a large number of hitherto undiscovered excited electronic states in both charge states as evidenced by distinct optical transitions in the infrared to ultraviolet part of the spectrum. These transitions are observed by monitoring the electronic relaxation of NV centers after photoexcitation using transient absorption spectroscopy, directly probing transient phenomena occurring on timescales from femtoseconds to microseconds. We also for the first time probed the electron transfer dynamics from the 3 E state of NV− to nearby single-substitutional nitrogen defects (N s ) that leads to the well-known effect of NV photoluminescence quenching.

Materials for Quantum Technology•Jul 10, 2024•17 citations

Laser-written nitrogen-vacancy centres in diamond membranes for quantum computing

Joe Gore

Manipulation of quantum effects for computing is an important step in the creation of faster and more powerful computational tools. The nitrogen vacancy centre (NVC) in diamond, when in the negative charge state, has shown significant promise towards being used as a qubit, such as optical polarization and readout, long coherence times (T∗ 2 and T2), and a long relaxation time T1. Such times are desired for producing good quantum memory, utilising the spin state of the sites. Cryogenic conditions are required for facilitating the optical entanglement of two NVC, and can serve to significantly extend these times. These sites have been created using a laser writing technique, capable of producing a large number of NVC with good coherence characteristics at arbitrary locations within diamond samples. This thesis reports on methods to reliably create NVC with good coherence characteristics for quantum computing applications by altering the annealing regime used. This annealing regime has been improved by the design and construction of a new vacuum furnace with better temperature control and thermometry. Steps towards the ideal combination of annealing conditions for a range of desired NV concentrations and characteristics have been undertaken, showing good conversion of laser written sites to NVC. NVC have been systematically tracked using a confocal fluorescence microscope apparatus throughout multiple annealing steps, with the collection of coherence data including T1, T2 and T∗ 2 on the same NV centre at multiple annealing temperatures, for the first time. This data allows for tracking of the influence of annealing temperature on the coherence properties of sites without the caveat of comparing data from either different sites, or different diamonds altogether. Such centres show coherence times above 800 μs, with production rates at and above 40% for single emitters. NVC are limited by their weak emission into the zero phonon line. These issues can be alleviated by increasing the collection efficiency of photons, which requires thin diamonds capable of being used with cavity systems. Steps towards producing such diamonds by a thin-region design have been undertaken and show promising results. Further efforts include the use of nanostructures on the diamond surface, which has been implemented and detailed. Magnetic control of NVC within diamond, especially at cryogenic temperatures, introduces some operational complexity to potential quantum operations. By implementing the use of diamond cut at the (111) crystal plane, this alignment is likely to become more straightforward, enabling future work with diamond at this crystal plane. Diamonds have been produced, with NVC laser written in, for the first time.

•Sep 17, 2026•0 citations

Chemical vapour deposition diamond single crystals with nitrogen-vacancy centres: a review of material synthesis and technology for quantum sensing applications

Jocelyn Achard, V. Jacques, Alexandre Tallaire

Abstract Diamond hosts a wide variety of colour centres that have demonstrated outstanding optical and spin properties. Among them, the nitrogen-vacancy (NV) centre is by far the most investigated owing to its superior characteristics, which promise the development of highly sophisticated quantum devices, in particular for sensing applications. Nevertheless, harnessing the potential of these centres mainly relies on the availability of high quality and purity diamond single crystals that need to be specially designed and engineered for this purpose. Plasma assisted chemical vapour deposition (CVD) has become a key enabling technology in this field of research. Nitrogen can indeed be directly doped in situ into a high crystalline quality diamond matrix in a controlled way, allowing the production of single isolated centres or ensembles that can potentially be integrated into a device. In this paper we will provide an overview of the requirements for synthesizing ‘quantum-grade’ diamond films using CVD. These include the reduction of impurities and surrounding spins that limit coherence times, the control of NV density in a wide range of concentrations as well as their spatial localization within the diamond. Enhancing the charge state and preferential orientation of the colour centres is also discussed. These improvements in material fabrication have contributed to positioning diamond as one of the most promising solid-state quantum systems and the first industrial applications in sensing are just starting to emerge.

arXiv:1912.09749•Journal of Physics D Applied Physics•Mar 20, 2020•136 citations
Emerging quantum technologies based on the nitrogen-vacancy (NV) centre in diamond require carefully engineered material with controlled defect density, optimised NV formation processes, and minimal crystal strain. The choice of NV generation technique plays a crucial role in determining the quality and performance of these centres. In this work, we investigate NV centre formation in nitrogen-doped diamond using femtosecond (fs) laser processing. We systematically examine the effect of laser pulse energy on NV production and quality using photoluminescence and optically detected magnetic resonance measurements. We also probe the role of pre-existing lattice defects formed by electron irradiation and consider defect evolution over extended dwell times. Finally, we are able to identify a regime where the main action of the fs-laser is to diffuse rather than create vacancies. This local annealing capability expands the toolkit for tailored NV production and presents opportunities for fine tuning defect populations.
High-density nitrogen-vacancy (NV) centers exceeding 1016/cm3 inside a diamond can be achieved by femtosecond laser irradiation. The number of pulses and pulse energy were adjusted considering the increasing trend of the NV concentration and damage generation. The NV concentration first grew as the number of laser pulses was increased, and then the concentration was temporarily saturated or decreased. By increasing the number of laser pulses more than 2.5–5 × 107, the concentration increased again. The Hahn-echo measurement revealed that electron spins of the substitutional nitrogen center (P1) were dominant source for decoherence and the number of paramagnetic defects induced by the laser irradiation was not significant for degradation of spin coherence of the laser-induced NV centers even without a post-annealing process. Such high-dense ensemble NV centers are crucial for a high-sensitive quantum sensor.
Colour centre defects in diamond are promising candidates for many quantum technologies because they act as isolated two level systems in the solid-state that can be controlled and read-out through photonics [1][2][3]. Realisation of these technologies requires the placement of many highly coherent centres in a regular array with high positional accuracy and high fabrication yield [4]. Previous fabrication techniques have lacked the ability to produce high yields with high positional accuracy without causing irreparable damage to the lattice which reduced the quality of the spin and optical properties [5]. Ultra-fast laser writing has been shown to produce highly coherent nitrogen vacancy (NV) colour centres within the diamond lattice with positional accuracies of order hundreds of nanometers and a stochastic yield. In this case, the yield and positional accuracy is held back by the need to thermally anneal the diamond within a furnace to convert laser generated defects into colour centres; a fabrication step in which there is little to no control over individual site [6]. In this thesis, the ultra-fast pulsed laser writing technique is broached in detail from both a theoretical and experimental standpoint. The theory behind the highly non-linear light-matter interactions is studied and a hypothesis is developed for the energy transfer between photo-excited carriers and the lattice via the non-radiative recombination of self-trapped multi-excitonic states [7]. In addition, this thesis presents an expansion on the laser writing of colour centres through broaching the generation of different colour centres that have some preferential properties over the NV [8], and the development of a new engineering technique involving a local laser anneal [9]. The yield of generated centres is increased from stochastic to deterministic by replacing the global thermal anneal with the local laser anneal in combination with a fluorescence feedback mechanism. In addition, the use of the laser to locally anneal generated centres leads to a factor of five improvement in the positional accuracy due to the highly non-linear interaction of the laser with the material. These results culminate in a key step forward in the development of a large scale quantum device and improved understanding of the highly dynamical processes that occur upon femtosecond laser interaction with a wide bandgap material.
Abstract The nitrogen-vacancy (NV) center in diamond is a promising quantum system for magnetometry applications exhibiting optical readout of minute energy shifts in its spin sub-levels. Key material requirements for NV ensembles are a high NV − concentration, a long spin coherence time and a stable charge state. However, these are interdependent and can be difficult to optimize during diamond growth and subsequent NV creation. In this work, we systematically investigate the NV center formation and properties in bulk chemical vapor deposition (CVD) diamond. The nitrogen flow during growth is varied by over four orders of magnitude, resulting in a broad range of single substitutional nitrogen concentrations of 0.2–20 parts per million. For a fixed nitrogen concentration, we optimize electron-irradiation fluences with two different accelerated electron energies, and we study defect formation via optical characterizations. We discuss a general approach to determine the optimal irradiation conditions, for which an enhanced NV concentration and an optimum of NV charge states can both be satisfied. We achieve spin–spin coherence times T 2 ranging from 45.5 to 549 μ s for CVD diamonds containing 168 to 1 parts per billion NV − centers, respectively. This study shows a pathway to engineer properties of NV-doped CVD diamonds for improved sensitivity.
Abstract Nitrogen-vacancy (NV) defect centers in diamond are key to applications in quantum sensing and quantum computing. They create localized electronic states in the diamond lattice with distinct population relaxation pathways following photoexcitation that ultimately enable its unique properties. The defect is known to exist in two charge states: neutral and negative, with respectively one and two known optically-active electronic transitions. Here, we report on the observation of a large number of hitherto undiscovered excited electronic states in both charge states as evidenced by distinct optical transitions in the infrared to ultraviolet part of the spectrum. These transitions are observed by monitoring the electronic relaxation of NV centers after photoexcitation using transient absorption spectroscopy, directly probing transient phenomena occurring on timescales from femtoseconds to microseconds. We also for the first time probed the electron transfer dynamics from the 3 E state of NV− to nearby single-substitutional nitrogen defects (N s ) that leads to the well-known effect of NV photoluminescence quenching.
Manipulation of quantum effects for computing is an important step in the creation of faster and more powerful computational tools. The nitrogen vacancy centre (NVC) in diamond, when in the negative charge state, has shown significant promise towards being used as a qubit, such as optical polarization and readout, long coherence times (T∗ 2 and T2), and a long relaxation time T1. Such times are desired for producing good quantum memory, utilising the spin state of the sites. Cryogenic conditions are required for facilitating the optical entanglement of two NVC, and can serve to significantly extend these times. These sites have been created using a laser writing technique, capable of producing a large number of NVC with good coherence characteristics at arbitrary locations within diamond samples. This thesis reports on methods to reliably create NVC with good coherence characteristics for quantum computing applications by altering the annealing regime used. This annealing regime has been improved by the design and construction of a new vacuum furnace with better temperature control and thermometry. Steps towards the ideal combination of annealing conditions for a range of desired NV concentrations and characteristics have been undertaken, showing good conversion of laser written sites to NVC. NVC have been systematically tracked using a confocal fluorescence microscope apparatus throughout multiple annealing steps, with the collection of coherence data including T1, T2 and T∗ 2 on the same NV centre at multiple annealing temperatures, for the first time. This data allows for tracking of the influence of annealing temperature on the coherence properties of sites without the caveat of comparing data from either different sites, or different diamonds altogether. Such centres show coherence times above 800 μs, with production rates at and above 40% for single emitters. NVC are limited by their weak emission into the zero phonon line. These issues can be alleviated by increasing the collection efficiency of photons, which requires thin diamonds capable of being used with cavity systems. Steps towards producing such diamonds by a thin-region design have been undertaken and show promising results. Further efforts include the use of nanostructures on the diamond surface, which has been implemented and detailed. Magnetic control of NVC within diamond, especially at cryogenic temperatures, introduces some operational complexity to potential quantum operations. By implementing the use of diamond cut at the (111) crystal plane, this alignment is likely to become more straightforward, enabling future work with diamond at this crystal plane. Diamonds have been produced, with NVC laser written in, for the first time.
Abstract Diamond hosts a wide variety of colour centres that have demonstrated outstanding optical and spin properties. Among them, the nitrogen-vacancy (NV) centre is by far the most investigated owing to its superior characteristics, which promise the development of highly sophisticated quantum devices, in particular for sensing applications. Nevertheless, harnessing the potential of these centres mainly relies on the availability of high quality and purity diamond single crystals that need to be specially designed and engineered for this purpose. Plasma assisted chemical vapour deposition (CVD) has become a key enabling technology in this field of research. Nitrogen can indeed be directly doped in situ into a high crystalline quality diamond matrix in a controlled way, allowing the production of single isolated centres or ensembles that can potentially be integrated into a device. In this paper we will provide an overview of the requirements for synthesizing ‘quantum-grade’ diamond films using CVD. These include the reduction of impurities and surrounding spins that limit coherence times, the control of NV density in a wide range of concentrations as well as their spatial localization within the diamond. Enhancing the charge state and preferential orientation of the colour centres is also discussed. These improvements in material fabrication have contributed to positioning diamond as one of the most promising solid-state quantum systems and the first industrial applications in sensing are just starting to emerge.