Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2504.00933 · Review of Scientific Instruments

Filter circuit for suppression of electric-field noise in Rydberg-atom experiments

Xinyan Xiang, Shuaijie Li, Alisher Duspayev, Ian Hoffman, L. Zhou, Bineet Dash, Carlos Owens, Anisa Tapper, Georg A. Raithel

Published Sep 1, 2025• 1 citation
arXivHTMLPDF

Abstract

Rydberg atoms are widely employed in precision spectroscopy and quantum information science. To minimize atomic decoherence caused by the dc Stark effect, the electric field noise at the Rydberg atom location should be kept below ∼10 mV/cm. Here, we present a simple yet effective electronic circuit, referred to as a clamp switch, that allows one to realize such conditions. The clamp switch enables precise low-noise electric field control while allowing application of fast high-voltage ionization pulses through the same electrode(s), enabling atom detection via electric-field ionization and electron or ion counting. We outline the circuit design and analyze its noise suppression performance for both small and large input signals. In application examples, we employ the clamp switch to reduce the spectral width and increase the signal strength of a Rydberg line by a factor of two, to estimate the electric-field noise in the testing chamber, and to perform electric-field calibration using Rydberg Stark spectroscopy. The clamp switch improves coherence times and spectroscopic resolution in fundamental and applied quantum science research with Rydberg atoms.

DOI
10.1063/5.0276219

Related papers

Super low-frequency electric field measurement based on Rydberg atoms

Ling Li, Yuechun Jiao, Jinlian Hu +4 more

We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.

Optics Express•Aug 9, 2023•49 citations

Low-frequency electric field sensing with a Rydberg beam

Jeremy Glick, John DICKSON, Josie Wood +1 more

We present a method for performing low-frequency electric-field sensing via ionization detection of Rydberg atoms in a collimated atomic beam. A collimated beam avoids many of the electric-field screening effects that are common in warm vapor cells due to the accumulation of alkali-metal atoms on glass surfaces. Further, a beam facilitates a spatially separated region for high signal-to-noise readout via ionization detection. Using this approach, we measure dc Stark shifts from external fields with frequencies as low as 1 Hz. The sensor demonstrates a sensitivity of better than 1 mV / m Hz for frequencies above 20 Hz and 0.14(4) mV / m Hz above 500 Hz with a linear dynamic range of over 50 dB.

arXiv:2604.01513•Physical Review A•Jun 15, 2026•3 citations

Measurement of low-frequency electric field waveform by Rydberg atom-based sensor

Xuechao Zhang, Jia-Hui Qiao, Yao Liu +6 more

The high polarizability of Rydberg atoms enables the multi-parameters measurement of electromagnetic fields. In this paper, we report on an atomic antenna based on Rydberg atoms in a room temperature vapor cell. The EIT is a destructive interference spectroscopy with a narrow linewidth and can be used to detect small electric fields through Autler-Townes splitting or Stark shifts. In our experiments, we employ cascade-type two-photon excitation electromagnetically induced transparency (EIT) spectroscopy to measure the shift of the Rydberg energy level. We introduce a low-frequency electric field (~kHz frequency) using a built-in electrode technique in the cesium cell. The interaction between the Rydberg atom and electric field induces the Stark shifts, where the amplitude of the electric field is converted into corresponding two-photon detuning by the EIT effect. Furthermore, the amplitude of the low-frequency electric field is converted into an intensity signal of EIT probe beam. Under weak field conditions, it is an approximate linear relationship between EIT transmission signal and input electric field amplitude, enabling measurement of waveform, amplitude, and frequency. We have demonstrated optical measurements of low-frequency electric field using Rydberg atoms. By increasing the power of probe beam and coupling beam, the EIT can increase the response bandwidth from ~MHz to hundreds of MHz. This provides a scalable approach for measuring high-frequency electric fields.

Acta Physica Sinica•Jan 1, 2024•4 citations

Very sensitive vapor-cell quasi-DC atomic E-field sensor

Amy Damitz, George Burns, Yuan-Yu Jau

We report several technical approaches that significantly improve the performance of a vapor-cell atomic electrometer operating in the quasi-DC frequency domain ($\ll$ 1 kHz). With a very small active volume of approximately 11 mm$^3$ inside the vapor cell, we demonstrated a noise floor for electric field (E-field) sensitivity ranging from 0.2 to 7.7 mV/m$\sqrt{\rm Hz}$ for a frequency band of 1--100 Hz. Our work utilizes only a bare vapor cell for electrometry, without any metal parts or electrodes, to ensure minimal distortion of the measured E-field and to minimize the effective sensing volume for high spatial resolution. The E-field-sensitive atomic state (Rydberg state) is excited and read out optically, maximizing the simplicity of the system design and enabling the miniaturization of quasi-DC E-field sensors for potential applications, such as diagnostics of electronics without physical contact, communications in and below the super-low frequency (SLF) band, proximity detection, remote activity surveillance, tracing charge signatures, and research in bioscience and geoscience.

physics.atom-phCross-listedarXiv:2603.23751•Physical Review Applied•Mar 26, 2026•1 citation

Electric field sensing via Rydberg electromagnetically induced transparency using Zeeman and Stark effects

Y. C. Chen, Shao-Cheng Fang, Hsuan-Jui Su +1 more

Rydberg-assisted atomic electrometry with thermal vapors offers a promising approach for detecting external electric fields. However, this technique presents significant challenges for measuring low frequencies due to the effects of metal-alkali atoms adsorbed on the interior surface of the vacuum chamber. In this work, we apply high-contrast Rydberg electromagnetically induced transparency (EIT) spectroscopy to systematically investigate these effects, including the influence of laser power and electric field strength. We demonstrate the ability to measure electric field frequencies ranging from 10 Hz to 1 MHz. Additionally, this study identifies a fundamental limit for data capacity in such measurements. Furthermore, we propose a method for precise Stark shift measurements by locking the coupling laser to Zeeman-split Rydberg EIT peaks. Using the Zeeman shift in a reference cell as a stable frequency reference, we are able to track Stark-induced shifts in a science cell and confirm excellent agreement with theoretical predictions. These results provide valuable insights for future precision measurement techniques and field sensing applications based on Rydberg atom systems.

arXiv:2402.01430•Journal of Applied Physics•Sep 2, 2025•3 citations

Quantum sensing of low-frequency electric signal enabled by modulated auxiliary field in Rydberg atoms

Xiayang Fan, Shenchao Jin, Jiatian Liu +3 more

Rydberg atoms have emerged as a versatile and efficient platform for high-sensitivity quantum sensing of free-space electric fields, with remarkable progress in detecting low-frequency signals. To date, low-frequency Rydberg receivers have relied on a constant bias field, typically realized via intra-cell electrodes or Rydberg plasmas generated by photoelectric effects or inter-atomic interactions. While these approaches improve sensitivity, they suffer from inherent challenges in calibration, long-term stability, and robustness, hindering practical deployment. Here, we propose, design, and experimentally demonstrate a quantum sensing scheme for low-frequency electric signals using modulated auxiliary fields in Rydberg atoms. Unlike conventional methods that employ external DC electric fields that are often fully shielded by adsorbed atom layers on the cell walls, we introduce an AC-field modulation strategy. The incoming low-frequency signal mixes with the auxiliary field, and together they induce Stark shifts of the Rydberg level. These shifts are mapped onto the probe laser via electromagnetically induced transparency (EIT), in a manner analogous to heterodyne detection. We demonstrate a sensitivity of $7.5 \pm 2.6~\mathrm{μV/(cm\cdot Hz^{1/2})}$ at 5 kHz and a minimal detectable field of $0.26 \pm 0.04~\mathrm{μV/cm}$ with an integration time of 1000 s. Furthermore, we extend this approach to systematically analyze the performance of generalized auxiliary fields containing multiple frequency components. By virtue of modulated auxiliary field and quantum frequency mixing, our results establish a robust and systematic framework for quantum sensing of low-frequency electric fields with Rydberg atoms, offering improved sensitivity, stability, and immunity to environmental drifts.

quant-pharXiv:2607.18740•Jul 22, 2026•0 citations
Rydberg atoms are widely employed in precision spectroscopy and quantum information science. To minimize atomic decoherence caused by the dc Stark effect, the electric field noise at the Rydberg atom location should be kept below ∼10 mV/cm. Here, we present a simple yet effective electronic circuit, referred to as a clamp switch, that allows one to realize such conditions. The clamp switch enables precise low-noise electric field control while allowing application of fast high-voltage ionization pulses through the same electrode(s), enabling atom detection via electric-field ionization and electron or ion counting. We outline the circuit design and analyze its noise suppression performance for both small and large input signals. In application examples, we employ the clamp switch to reduce the spectral width and increase the signal strength of a Rydberg line by a factor of two, to estimate the electric-field noise in the testing chamber, and to perform electric-field calibration using Rydberg Stark spectroscopy. The clamp switch improves coherence times and spectroscopic resolution in fundamental and applied quantum science research with Rydberg atoms.
We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.
We present a method for performing low-frequency electric-field sensing via ionization detection of Rydberg atoms in a collimated atomic beam. A collimated beam avoids many of the electric-field screening effects that are common in warm vapor cells due to the accumulation of alkali-metal atoms on glass surfaces. Further, a beam facilitates a spatially separated region for high signal-to-noise readout via ionization detection. Using this approach, we measure dc Stark shifts from external fields with frequencies as low as 1 Hz. The sensor demonstrates a sensitivity of better than 1 mV / m Hz for frequencies above 20 Hz and 0.14(4) mV / m Hz above 500 Hz with a linear dynamic range of over 50 dB.
The high polarizability of Rydberg atoms enables the multi-parameters measurement of electromagnetic fields. In this paper, we report on an atomic antenna based on Rydberg atoms in a room temperature vapor cell. The EIT is a destructive interference spectroscopy with a narrow linewidth and can be used to detect small electric fields through Autler-Townes splitting or Stark shifts. In our experiments, we employ cascade-type two-photon excitation electromagnetically induced transparency (EIT) spectroscopy to measure the shift of the Rydberg energy level. We introduce a low-frequency electric field (~kHz frequency) using a built-in electrode technique in the cesium cell. The interaction between the Rydberg atom and electric field induces the Stark shifts, where the amplitude of the electric field is converted into corresponding two-photon detuning by the EIT effect. Furthermore, the amplitude of the low-frequency electric field is converted into an intensity signal of EIT probe beam. Under weak field conditions, it is an approximate linear relationship between EIT transmission signal and input electric field amplitude, enabling measurement of waveform, amplitude, and frequency. We have demonstrated optical measurements of low-frequency electric field using Rydberg atoms. By increasing the power of probe beam and coupling beam, the EIT can increase the response bandwidth from ~MHz to hundreds of MHz. This provides a scalable approach for measuring high-frequency electric fields.
We report several technical approaches that significantly improve the performance of a vapor-cell atomic electrometer operating in the quasi-DC frequency domain (≪\ll≪ 1 kHz). With a very small active volume of approximately 11 mm3^33 inside the vapor cell, we demonstrated a noise floor for electric field (E-field) sensitivity ranging from 0.2 to 7.7 mV/mHz\sqrt{\rm Hz}Hz​ for a frequency band of 1--100 Hz. Our work utilizes only a bare vapor cell for electrometry, without any metal parts or electrodes, to ensure minimal distortion of the measured E-field and to minimize the effective sensing volume for high spatial resolution. The E-field-sensitive atomic state (Rydberg state) is excited and read out optically, maximizing the simplicity of the system design and enabling the miniaturization of quasi-DC E-field sensors for potential applications, such as diagnostics of electronics without physical contact, communications in and below the super-low frequency (SLF) band, proximity detection, remote activity surveillance, tracing charge signatures, and research in bioscience and geoscience.
Rydberg-assisted atomic electrometry with thermal vapors offers a promising approach for detecting external electric fields. However, this technique presents significant challenges for measuring low frequencies due to the effects of metal-alkali atoms adsorbed on the interior surface of the vacuum chamber. In this work, we apply high-contrast Rydberg electromagnetically induced transparency (EIT) spectroscopy to systematically investigate these effects, including the influence of laser power and electric field strength. We demonstrate the ability to measure electric field frequencies ranging from 10 Hz to 1 MHz. Additionally, this study identifies a fundamental limit for data capacity in such measurements. Furthermore, we propose a method for precise Stark shift measurements by locking the coupling laser to Zeeman-split Rydberg EIT peaks. Using the Zeeman shift in a reference cell as a stable frequency reference, we are able to track Stark-induced shifts in a science cell and confirm excellent agreement with theoretical predictions. These results provide valuable insights for future precision measurement techniques and field sensing applications based on Rydberg atom systems.
Rydberg atoms have emerged as a versatile and efficient platform for high-sensitivity quantum sensing of free-space electric fields, with remarkable progress in detecting low-frequency signals. To date, low-frequency Rydberg receivers have relied on a constant bias field, typically realized via intra-cell electrodes or Rydberg plasmas generated by photoelectric effects or inter-atomic interactions. While these approaches improve sensitivity, they suffer from inherent challenges in calibration, long-term stability, and robustness, hindering practical deployment. Here, we propose, design, and experimentally demonstrate a quantum sensing scheme for low-frequency electric signals using modulated auxiliary fields in Rydberg atoms. Unlike conventional methods that employ external DC electric fields that are often fully shielded by adsorbed atom layers on the cell walls, we introduce an AC-field modulation strategy. The incoming low-frequency signal mixes with the auxiliary field, and together they induce Stark shifts of the Rydberg level. These shifts are mapped onto the probe laser via electromagnetically induced transparency (EIT), in a manner analogous to heterodyne detection. We demonstrate a sensitivity of 7.5±2.6 μV/(cm⋅Hz1/2)7.5 \pm 2.6~\mathrm{μV/(cm\cdot Hz^{1/2})}7.5±2.6 μV/(cm⋅Hz1/2) at 5 kHz and a minimal detectable field of 0.26±0.04 μV/cm0.26 \pm 0.04~\mathrm{μV/cm}0.26±0.04 μV/cm with an integration time of 1000 s. Furthermore, we extend this approach to systematically analyze the performance of generalized auxiliary fields containing multiple frequency components. By virtue of modulated auxiliary field and quantum frequency mixing, our results establish a robust and systematic framework for quantum sensing of low-frequency electric fields with Rydberg atoms, offering improved sensitivity, stability, and immunity to environmental drifts.