We present a method for performing low-frequency electric-field sensing via ionization detection of Rydberg atoms in a collimated atomic beam. A collimated beam avoids many of the electric-field screening effects that are common in warm vapor cells due to the accumulation of alkali-metal atoms on glass surfaces. Further, a beam facilitates a spatially separated region for high signal-to-noise readout via ionization detection. Using this approach, we measure dc Stark shifts from external fields with frequencies as low as 1 Hz. The sensor demonstrates a sensitivity of better than 1 mV / m Hz for frequencies above 20 Hz and 0.14(4) mV / m Hz above 500 Hz with a linear dynamic range of over 50 dB.
We present a method for performing low-frequency electric-field sensing via ionization detection of Rydberg atoms in a collimated atomic beam. A collimated beam avoids many of the electric-field screening effects that are common in warm vapor cells due to the accumulation of alkali-metal atoms on glass surfaces. Further, a beam facilitates a spatially separated region for high signal-to-noise readout via ionization detection. Using this approach, we measure dc Stark shifts from external fields with frequencies as low as 1 Hz. The sensor demonstrates a sensitivity of better than 1 mV / m Hz for frequencies above 20 Hz and 0.14(4) mV / m Hz above 500 Hz with a linear dynamic range of over 50 dB.
We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.
Fields with frequencies below megahertz are challenging for Rydberg-atom-based measurements, due to the low-frequency electric field screening effect caused by the alkali-metal atoms adsorbed on the inner surface of the container. In this paper, we investigate electric field measurements in the ultralow frequency (ULF), very low frequency (VLF), and low frequency (LF) bands in a Cs vapor cell with built-in parallel electrodes. With optimization of the applied DC field, we achieve high-sensitive detection of the electric field at frequencies of 1 kHz, 10 kHz, and 100 kHz based on the Rydberg-atom sensor, with the minimum electric field strength down to 18.0 μV/cm, 6.9 μV/cm, and 3.0 μV/cm, respectively. The corresponding sensitivity is 5.7 μV/cm/Hz 1/2 , 2.2 μV/cm/Hz 1/2 , and 0.95 μV/cm/Hz 1/2 for the ULF, VLF, and LF fields, which is better than a 1-cm dipole antenna. Besides, the linear dynamic range of the Rydberg-atom sensor is over 50 dB. This work presents the potential to enable more applications that utilize atomic sensing technology in the ULF, VLF, and LF fields.
Rydberg-atom electric field sensing has shown great potential from near-DC to THz with state-of-the-art measurement metrics realized in sensitivity, phase extraction, multi-band receptivity, etc. While Rydberg-atom sensors have shown exceptional performance in the GHz regime, low-frequency operation has remained challenging because of electric-field-screening in conventional vapor cells, which suppresses externally applied fields. We overcome this limitation by combining auxiliary modulation and lock-in detection with a paraffin-coated vapor cell, and demonstrate an electrode-free, wideband method for sensing frequencies, ranging from 0.5 Hz to 10 kHz. Our work extends Rydberg-atom sensor range to VLF, ULF, SLF, ELF and sub-ELF frequency bands. In our method, high state-of-the-art sensitivities have been achieved - 819 μV/cm/Hz for 1 Hz, 33 μV/cm/Hz for 10 Hz, 10 μV/cm/Hz for 100 Hz and 2 μV/cm/Hz for 1 kHz.
Low-frequency (LF) electric-field measurements with Rydberg atoms are limited by alkali-induced cell-surface screening and excess laser-intensity noise. Here, we address these limitations using a Cs vapor cell with built-in parallel electrodes, active laser-power stabilization, and a home-built balanced detector to suppress 10 Hz-kHz intensity noise. A 15 kHz local-oscillator field is introduced to up-convert Hz-scale signals to the lower-noise kHz band through Rydberg atom-mediated sum-frequency mixing (SFM), improving the optical readout signal-to-noise ratio. The system achieves a minimum detectable electric field of 190 nV/cm within 0.5 Hz-1.006 kHz, a linear dynamic range exceeding 67 dB, and a spectral resolution of 18 mHz.
We report several technical approaches that significantly improve the performance of a vapor-cell atomic electrometer operating in the quasi-DC frequency domain (≪ 1 kHz). With a very small active volume of approximately 11 mm3 inside the vapor cell, we demonstrated a noise floor for electric field (E-field) sensitivity ranging from 0.2 to 7.7 mV/mHz for a frequency band of 1--100 Hz. Our work utilizes only a bare vapor cell for electrometry, without any metal parts or electrodes, to ensure minimal distortion of the measured E-field and to minimize the effective sensing volume for high spatial resolution. The E-field-sensitive atomic state (Rydberg state) is excited and read out optically, maximizing the simplicity of the system design and enabling the miniaturization of quasi-DC E-field sensors for potential applications, such as diagnostics of electronics without physical contact, communications in and below the super-low frequency (SLF) band, proximity detection, remote activity surveillance, tracing charge signatures, and research in bioscience and geoscience.
Rydberg-assisted atomic electrometry with thermal vapors offers a promising approach for detecting external electric fields. However, this technique presents significant challenges for measuring low frequencies due to the effects of metal-alkali atoms adsorbed on the interior surface of the vacuum chamber. In this work, we apply high-contrast Rydberg electromagnetically induced transparency (EIT) spectroscopy to systematically investigate these effects, including the influence of laser power and electric field strength. We demonstrate the ability to measure electric field frequencies ranging from 10 Hz to 1 MHz. Additionally, this study identifies a fundamental limit for data capacity in such measurements. Furthermore, we propose a method for precise Stark shift measurements by locking the coupling laser to Zeeman-split Rydberg EIT peaks. Using the Zeeman shift in a reference cell as a stable frequency reference, we are able to track Stark-induced shifts in a science cell and confirm excellent agreement with theoretical predictions. These results provide valuable insights for future precision measurement techniques and field sensing applications based on Rydberg atom systems.