Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2501.13289 · Journal of Applied Physics

Effects of valley splitting on resonant-tunneling readout of spin qubits

Tetsufumi Tanamoto, Keiji Ono

Published Apr 25, 2025• 1 citation
arXivHTMLPDF

Abstract

The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source–drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time tmeas is much less than the decoherence time tdec such that tdec/tmeas>100. This suggests that less than 1% measurement error is anticipated, which opens up the possibility of implementing surface codes even in the presence of valley splitting.

DOI
10.1063/5.0260516

Related papers

Readout using resonant tunneling in silicon spin qubits

Tetsufumi Tanamoto, Keiji Ono

Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.

arXiv:2308.15015•Journal of Applied Physics•Dec 4, 2023•6 citations

Proposal for a cavity-induced measurement of the exchange coupling in quantum dots

Florian Ginzel, Guido Burkard

In spin qubit arrays the exchange coupling can be harnessed to implement two-qubit gates and to realize intermediate-range qubit connectivity along a spin bus. In this work, we propose a scheme to characterize the exchange coupling between electrons in adjacent quantum dots. We investigate theoretically the transmission of a microwave resonator coupled to a triple quantum dot occupied by two electrons. We assume that the right quantum dot (QD) is always occupied by one electron while the second electron can tunnel between the left and center QDs. If the two electrons are in adjacent dots they interact via the exchange coupling. By means of analytical calculations we show that the transmission profile of the resonator directly reveals the value of the exchange coupling strength between two electrons. From perturbation theory up to second order we conclude that the exchange can still be identified in the presence of magnetic gradients. A valley splitting comparable to the interdot tunnel coupling will lead to further modifications of the cavity transmission dips that also depend on the valley phases.

arXiv:2202.00797•Physical Review Research•Jul 18, 2022•3 citations

Singlet-triplet oscillations in multivalley Si double quantum dots

Łukasz Cywiński, Mats Volmer, Tom Struck +2 more

Charge separation from the $(4,0)$ to the $(3,1)$ state in a Si/SiGe double quantum dot is commonly used for initialization of spin qubits and Pauli-spin-blockade readout. It was used in recent experiments involving creation of the $(3,1)$ singlet, and subsequent shuttling of one of the electrons. We present a theoretical description of the process of charge separation and singlet-triplet mixing, arriving at expressions for the singlet return probability that take into account experimentally observed finite probabilities of the creation of singlets with various patterns of valley occupations. In our analysis we focus on magnetic fields for which the electron spin Zeeman splitting is close to the valley splitting in one of the dots, when the spin-valley coupling causes a strong renormalization of the frequency of oscillations of singlet return probability. The latter effect has been recently used to perform valley splitting mapping by shuttling of one quantum dot to various locations with respect to the other. We give a detailed description of singlet-triplet dynamics near these spin-valley resonances and compare the results of calculations with measurements on double quantum dots in two distinct Si/SiGe heterostructures. Comparison of theory with experiments in which the presence of a few valley occupation patterns is visible, gives insight into the valley dependence of $g$-factors in these structures, providing support for a recently proposed theoretical model of this dependence. We also discuss how dephasing of singlet return probability oscillations near the spin-valley resonances is affected by valley splitting fluctuations caused by electric field noise.

cond-mat.mes-hallCross-listedarXiv:2604.24689•Apr 28, 2026

Confinement drives valley splitting above 4K in buried silicon quantum wells

Davide Degli Esposti, Emma Catherine Brann, Asser Elsayed +3 more

Controlling the energy scales of a quantum system is essential for defining robust qubits. In silicon spin qubits, the nearly degenerate conduction-band valleys create a leakage channel from the single-spin computational basis, posing a challenge to scaling and to shuttling-based architectures. Here, we measure the relevant energy scales of single-electron spin qubits in buried silicon quantum wells co-designed for low disorder and high valley splitting. Across a linear array of four quantum dots with an average orbital energy of 2.4(2) meV, we report an average single-electron valley splitting of 0.40(6) meV and an average two-electron singlet-triplet splitting of 0.24(7) meV. In three dots, we observe a strong correlation between valley splitting and orbital energy, with an average linear coefficient of $\approx 0.22$ (meV/meV), demonstrating that electrostatic confinement can increase the valley splitting by several hundred microelectronvolts. In contrast, the remaining dot exhibits the highest valley splitting of 0.76(2) meV and low correlation, suggesting excellent characteristics for spin-qubit operation. Our findings demonstrate that strong confinement can be exploited in buried quantum wells to effectively enhance the valley splitting, thereby establishing a viable path toward the realization of shuttling and sparse-occupation-based architectures in low-disorder heterostructures.

cond-mat.mes-hallCross-listedarXiv:2607.09570•Jul 13, 2026

Assessing quantum dot SWAP gate fidelity using tensor network methods

Jacob R. Taylor, Nathan L. Foulk, S. Das Sarma

Advanced tensor network numerical methods are used to explore the fidelity of repeated SWAP operations on a system comprising 20--100 quantum dot spin qubits in the presence of valley leakage and electrostatic crosstalk. The fidelity of SWAP gates is largely unaffected by Zeeman splitting and valley splitting, except when these parameters come into resonance. The fidelity remains independent of the overall valley phase for valley eigenstates, while for generic valley states, some minor corrections arise. We analyze the fidelity scaling for long qubit chains without valley effects, where crosstalk represents the only error source.

arXiv:2307.15177•Physical review. B./Physical review. B•Apr 1, 2024•2 citations

Anisotropic spin-valley coupling in SiMOS and Si/SiGe quantum dots

N. Tobias Jacobson, Natalie D. Foster, Ryan M. Jock +5 more

While bulk silicon has long been understood to exhibit relatively weak spin-orbit coupling (SOC), confinement of electrons to quantum dots (QDs) at a silicon heterointerface results in significantly larger SOC. This is a concern for electron spin qubit performance, as intravalley and intervalley SOC can significantly perturb the operation of electron spin qubits. While these interactions can be harnessed to drive coherent rotations in a singlet-triplet qubit, coupling to low-lying excited valley states can lead to undesirable spin relaxation when valley splitting is on resonance with the Zeeman energy. In this work, we measure the angular dependence of the interfacial spin-orbit interaction as a function of the direction and magnitude of an applied external magnetic field in SiMOS and Si/SiGe heterostructures, two common material platforms for silicon spin qubits. We construct a physical model that accurately infers intra- and inter-valley SOC physics from fits to the data, allowing for a direct comparison between these two material systems. For the devices measured we find that, while the $g$-factor differences are comparable, the SiMOS QDs exhibit an order of magnitude larger spin-valley coupling than for Si/SiGe. Moreover, we find that the angular dependence of the spin-valley coupling is similar for both devices, with similar magnetic field orientations minimizing the spin-valley coupling. Our work points towards operational schemes for optimizing spin-valley coupling to avoid or exploit this mechanism for qubit operation.

cond-mat.mes-hallCross-listedarXiv:2604.16713•Apr 21, 2026
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source–drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time tmeas is much less than the decoherence time tdec such that tdec/tmeas>100. This suggests that less than 1% measurement error is anticipated, which opens up the possibility of implementing surface codes even in the presence of valley splitting.
Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.
In spin qubit arrays the exchange coupling can be harnessed to implement two-qubit gates and to realize intermediate-range qubit connectivity along a spin bus. In this work, we propose a scheme to characterize the exchange coupling between electrons in adjacent quantum dots. We investigate theoretically the transmission of a microwave resonator coupled to a triple quantum dot occupied by two electrons. We assume that the right quantum dot (QD) is always occupied by one electron while the second electron can tunnel between the left and center QDs. If the two electrons are in adjacent dots they interact via the exchange coupling. By means of analytical calculations we show that the transmission profile of the resonator directly reveals the value of the exchange coupling strength between two electrons. From perturbation theory up to second order we conclude that the exchange can still be identified in the presence of magnetic gradients. A valley splitting comparable to the interdot tunnel coupling will lead to further modifications of the cavity transmission dips that also depend on the valley phases.
Charge separation from the (4,0)(4,0)(4,0) to the (3,1)(3,1)(3,1) state in a Si/SiGe double quantum dot is commonly used for initialization of spin qubits and Pauli-spin-blockade readout. It was used in recent experiments involving creation of the (3,1)(3,1)(3,1) singlet, and subsequent shuttling of one of the electrons. We present a theoretical description of the process of charge separation and singlet-triplet mixing, arriving at expressions for the singlet return probability that take into account experimentally observed finite probabilities of the creation of singlets with various patterns of valley occupations. In our analysis we focus on magnetic fields for which the electron spin Zeeman splitting is close to the valley splitting in one of the dots, when the spin-valley coupling causes a strong renormalization of the frequency of oscillations of singlet return probability. The latter effect has been recently used to perform valley splitting mapping by shuttling of one quantum dot to various locations with respect to the other. We give a detailed description of singlet-triplet dynamics near these spin-valley resonances and compare the results of calculations with measurements on double quantum dots in two distinct Si/SiGe heterostructures. Comparison of theory with experiments in which the presence of a few valley occupation patterns is visible, gives insight into the valley dependence of ggg-factors in these structures, providing support for a recently proposed theoretical model of this dependence. We also discuss how dephasing of singlet return probability oscillations near the spin-valley resonances is affected by valley splitting fluctuations caused by electric field noise.
Controlling the energy scales of a quantum system is essential for defining robust qubits. In silicon spin qubits, the nearly degenerate conduction-band valleys create a leakage channel from the single-spin computational basis, posing a challenge to scaling and to shuttling-based architectures. Here, we measure the relevant energy scales of single-electron spin qubits in buried silicon quantum wells co-designed for low disorder and high valley splitting. Across a linear array of four quantum dots with an average orbital energy of 2.4(2) meV, we report an average single-electron valley splitting of 0.40(6) meV and an average two-electron singlet-triplet splitting of 0.24(7) meV. In three dots, we observe a strong correlation between valley splitting and orbital energy, with an average linear coefficient of ≈0.22\approx 0.22≈0.22 (meV/meV), demonstrating that electrostatic confinement can increase the valley splitting by several hundred microelectronvolts. In contrast, the remaining dot exhibits the highest valley splitting of 0.76(2) meV and low correlation, suggesting excellent characteristics for spin-qubit operation. Our findings demonstrate that strong confinement can be exploited in buried quantum wells to effectively enhance the valley splitting, thereby establishing a viable path toward the realization of shuttling and sparse-occupation-based architectures in low-disorder heterostructures.
Advanced tensor network numerical methods are used to explore the fidelity of repeated SWAP operations on a system comprising 20--100 quantum dot spin qubits in the presence of valley leakage and electrostatic crosstalk. The fidelity of SWAP gates is largely unaffected by Zeeman splitting and valley splitting, except when these parameters come into resonance. The fidelity remains independent of the overall valley phase for valley eigenstates, while for generic valley states, some minor corrections arise. We analyze the fidelity scaling for long qubit chains without valley effects, where crosstalk represents the only error source.
While bulk silicon has long been understood to exhibit relatively weak spin-orbit coupling (SOC), confinement of electrons to quantum dots (QDs) at a silicon heterointerface results in significantly larger SOC. This is a concern for electron spin qubit performance, as intravalley and intervalley SOC can significantly perturb the operation of electron spin qubits. While these interactions can be harnessed to drive coherent rotations in a singlet-triplet qubit, coupling to low-lying excited valley states can lead to undesirable spin relaxation when valley splitting is on resonance with the Zeeman energy. In this work, we measure the angular dependence of the interfacial spin-orbit interaction as a function of the direction and magnitude of an applied external magnetic field in SiMOS and Si/SiGe heterostructures, two common material platforms for silicon spin qubits. We construct a physical model that accurately infers intra- and inter-valley SOC physics from fits to the data, allowing for a direct comparison between these two material systems. For the devices measured we find that, while the ggg-factor differences are comparable, the SiMOS QDs exhibit an order of magnitude larger spin-valley coupling than for Si/SiGe. Moreover, we find that the angular dependence of the spin-valley coupling is similar for both devices, with similar magnetic field orientations minimizing the spin-valley coupling. Our work points towards operational schemes for optimizing spin-valley coupling to avoid or exploit this mechanism for qubit operation.