Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.
Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source–drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time tmeas is much less than the decoherence time tdec such that tdec/tmeas>100. This suggests that less than 1% measurement error is anticipated, which opens up the possibility of implementing surface codes even in the presence of valley splitting.
Spin qubits in gate-defined semiconductor quantum dots are a promising platform for realising a scalable quantum computer. This platform encodes quantum information into the intrinsic angular momentum (spin) of individual electrons or holes. In particular, hole spins in quantum dots enable the possibility of all-electrical spin control due to their intrinsic spin-orbit coupling. One important criterion of a quantum computer is the ability to reliably read out the state of the qubit. This is done by mapping spin information to the charge degree of freedom, combined with a method for charge detection. Charge detection can be facilitated by coupling a resonator directly to the quantum dot gate or to a charge sensor and measuring the resonator's phase or amplitude response. In this thesis, we describe a set of experiments relating to the implementation of hole spin qubit readout with superconducting resonators. First, we study gate-based charge sensing in a Si fin field-effect transistor (finFET) device using a superconducting NbN nanowire resonator. We find that the resonator amplifies capacitive crosstalk when electrical control pulses are applied to gate electrodes in this device. This occurs whenever a spectral component of qubit control pulses overlaps with the resonance frequency, which we show may occur for both baseband and radio-frequency (RF) drive signals. We quantify this crosstalk in a transport-based method, and attribute its source to the capacitance between the bondpads of neighbouring gate electrodes. In a second experiment, we use an RF charge sensor with the same nanowire technology to read out hole spin qubits formed in the quantum well of a Ge/SiGe heterostructure. A screening layer approach is used to facilitate RF matching due to large RF dissipation found in the heterostructure. We implement a double-latched readout scheme in this system to reduce errors arising from both spin and charge decay during readout. The spin-to-charge conversion process and its dependence on magnetic field orientation is studied. Spin and charge decay processes arising after spin-to-charge conversion are mitigated by choosing an optimal working point for the field orientation, field amplitude and readout pulse times. By doing so, we achieve an average single-shot state-preparation-and-measurement fidelity of 97%, primarily bounded by imperfect state preparation and limited signal-to-noise ratio. Finally, we study coplanar waveguide resonators fabricated from NbN. We investigate the feasibility of integrating this type of resonator onto the same chip as the Si finFET quantum dots. We then develop a novel resonator readout technique by the interference of two microwave sidebands. We demonstrate the insensitivity of this technique to common-mode phase and amplitude noise both theoretically and experimentally. This technique is then used to study resonator noise arising from two-level system defects. These results highlight both the practical constraints and the potential for achieving high readout fidelities using resonator-based hole spin qubit readout. This work establishes a blueprint for mitigating resonator-induced crosstalk and enabling high-fidelity readout in lossy materials by incorporating a screening layer.
Semiconductor quantum dots in silicon demonstrate exceptionally long spin lifetimes as qubits and are therefore promising candidates for quantum information processing. However, control and readout techniques for these devices have thus far employed low frequency electrons, in contrast to high speed temperature readout techniques used in other qubit architectures, and coupling between multiple quantum dot qubits has not been satisfactorily addressed.This dissertation presents the design and characterization of a semiconductor charge qubit based on double quantum dot in silicon with an integrated microwave resonator for control and readout. The 6 GHz resonator is designed to achieve strong coupling with the quantum dot qubit, allowing the use of circuit QED control and readout techniques which have not previously been applicable to semiconductor qubits. To achieve this coupling, this document demonstrates successful operation of a novel silicon double quantum dot design with a single active metallic layer and a coplanar stripline resonator with a bias tee for dc excitation.Experiments presented here demonstrate quantum localization and measurement of both electrons on the quantum dot and photons in the resonator. Further, it is shown that the resonator-qubit coupling in these devices is sufficient to reach the strong coupling regime of circuit QED. The details of a measurement setup capable of performing simultaneous low noise measurements of the resonator and quantum dot structure are also presented here.The ultimate aim of this research is to integrate the long coherence times observed in electron spins in silicon with the sophisticated readout architectures available in circuit QED based quantum information systems. This would allow superconducting qubits to be coupled directly to semiconductor qubits to create hybrid quantum systems with separate quantum memory and processing components.
Quantum computing is predicted to provide unprecedented enhancements in computational power. A quantum computer requires implementation of a well-defined and controlled quantum system of many interconnected qubits, each defined using fragile quantum states. The interest in a spin-based quantum computer in silicon stems from demonstrations of very long spin-coherence times, high-fidelity single spin control and compatibility with industrial mass-fabrication. Industrial scale fabrication of the silicon platform offers a clear route towards a large-scale quantum computer, however, some of the processes and techniques employed in qubit demonstrators are incompatible with a dense and foundry-fabricated architecture. In particular, spin-readout utilises external sensors that require nearly the same footprint as qubit devices. In this thesis, improved readout techniques for silicon quantum devices are presented and routes towards implementation of a scalable and high-sensitivity readout architecture are investigated. Firstly, readout sensitivity of compact gate-based sensors is improved using a high-quality factor resonator and Josephson parametric amplifier that are fabricated separately from quantum dots. Secondly, an integrated transistor-based control circuit is presented using which sequential readout of two quantum dot devices using the same gate-based sensor is achieved. Finally, a large-scale readout architecture based on random-access and frequency multiplexing is introduced. The impact of readout circuit footprint on readout sensitivity is determined, showing routes towards integration of conventional circuits with quantum devices in a dense architecture, and a fault-tolerant architecture based on mediated exchange is introduced, capable of relaxing the limitations on available control circuit footprint per qubit. Demonstrations are based on foundry-fabricated transistors and few-electron quantum dots, showing that industry fabrication is a viable route towards quantum computation at a scale large enough to begin addressing the most challenging computational problems.
The hybrid system of electron spins and resonator photons is an attractive architecture for quantum computing owing to the long coherence times of spins and the promise of long-distance coupling between arbitrary pairs of qubits via photons. For the device to serve as a building block for a quantum processer, it is also necessary to readout the spin qubit state. Here we analyze in detail the measurement process of an electron spin singlet-triplet qubit in quantum dots using a coupled superconducting resonator. We show that the states of the spin singlet-triplet qubit lead to readily observable features in the spectrum of a microwave field through the resonator. These features provide useful information on the hybrid system. Moreover, we discuss the working points which can be implemented with high performance in the current state-of-the-art devices. These results can be used to construct the high fidelity measurement toolbox in the spin-circuit QED system.
The understanding of quantum mechanics enabled the development of technology such as transistors and has been the foundation of today’s information age. Actively using quantum mechanics to build quantum technology may cause a second revolution in handling information. However, to execute meaningful algorithms, largescale quantum computers have to be built. Such systems are constructed from many qubits, the quantum version of the classical bit. While exciting progress is being made across a range of different qubit platforms, achieving the radical scalability that is necessary to build a largescale processor could be a roadblock. Huge challenges are put on reproducibility, inand output connectivity and material quality. Qubits based on the spins of electrons and holes confined in semiconductor quantum dots may have an important advantage in constructing quantum processors. This platform can profit from the advanced semiconductor industry that was responsible for the first computing revolution. Group IV semiconductors such as silicon and germanium have a high compatibility with industrial semiconductor manufacturing and contain stable isotopes with zero nuclear spin. The materials can be isotopically purified and serve as excellent hosts for spins with long quantum coherence. In Chapter 3 we present quantum dot arrays in silicon metaloxidesemiconductor (SiMOS), strained silicon (Si/SiGe) and strained germanium (Ge/SiGe). A nearly identical integration scheme based on an overlapping gate structure can be used to define quantum dots in each platform. Each platform has its own opportunities, which are carefully assessed. By employing charge sensing we confirm that all quantum dots can be depleted to the singleelectron regime. We compare capacitive crosstalk and find it to be the smallest in SiMOS, relevant for the tuning of quantum dot arrays. Using this crossplatform integration, we can study qubits in each platform with minimal overhead. Long coherence times, excellent singlequbit gate fidelities and twoqubit logic have been demonstrated with SiMOS spin qubits, making it one of the leading platforms for quantum information processing. However, due to the high disorder at the Si/SiO2 interface compared to Ge/SiGe and Si/SiGe interface, quantum dots defined in SiMOS are small and achieving sufficient control over single electrons has been a long standing challenge. In Chapter 5 we show experiments on a double quantum dot that can be isolated from its reservoir. We demonstrate a tunable tunnel coupling between single electrons up to 13 GHz and tunable tunnel rates down to below 1 Hz. These results mark an important step towards the required degree of control over the location of and coupling between quantum dots, necessary for the operation of a large array.