Quantum coherence in superconducting circuits has increased steadily over the last decades as a result of a growing understanding of the various loss mechanisms. Recently, tantalum (Ta) emerged as a promising material to address microscopic sources of loss found on niobium (Nb) or aluminum (Al) surfaces. However, the effects of film and interface microstructure on low-temperature microwave loss are still not well understood. Here we present a systematic study of the structural and electrical properties of Ta and Nb films sputtered on c-plane sapphire at varying growth temperatures. As growth temperature is increased, our results show that the onset of epitaxial growth of alpha-phase Ta correlates with lower Ta surface roughness, higher critical temperature, and higher residual resistivity ratio, but surprisingly also correlates with a significant increase in loss at microwave frequency. Notably, this high level of loss is not observed in Nb films prepared in the same way and having very similar structure. By experimentally controlling the surface on which the Ta film is nucleated, we determine that the source of loss is only present in samples having an epitaxial Ta/sapphire interface and show that it is apparently mitigated by either growing a thin, epitaxial Nb inter-layer between the Ta film and the substrate or by intentionally treating, and effectively damaging, the sapphire surface with an in-situ argon plasma before Ta growth. In addition to elucidating this interfacial microwave loss, this work provides adequate process details to aid reproducible growth of low-loss Ta films across fabrication facilities.
Quantum coherence in superconducting circuits has increased steadily over the last decades as a result of a growing understanding of the various loss mechanisms. Recently, tantalum (Ta) emerged as a promising material to address microscopic sources of loss found on niobium (Nb) or aluminum (Al) surfaces. However, the effects of film and interface microstructure on low-temperature microwave loss are still not well understood. Here we present a systematic study of the structural and electrical properties of Ta and Nb films sputtered on c-plane sapphire at varying growth temperatures. As growth temperature is increased, our results show that the onset of epitaxial growth of alpha-phase Ta correlates with lower Ta surface roughness, higher critical temperature, and higher residual resistivity ratio, but surprisingly also correlates with a significant increase in loss at microwave frequency. Notably, this high level of loss is not observed in Nb films prepared in the same way and having very similar structure. By experimentally controlling the surface on which the Ta film is nucleated, we determine that the source of loss is only present in samples having an epitaxial Ta/sapphire interface and show that it is apparently mitigated by either growing a thin, epitaxial Nb inter-layer between the Ta film and the substrate or by intentionally treating, and effectively damaging, the sapphire surface with an in-situ argon plasma before Ta growth. In addition to elucidating this interfacial microwave loss, this work provides adequate process details to aid reproducible growth of low-loss Ta films across fabrication facilities.
Building usefully coherent superconducting quantum processors depends on reducing losses in their constituent materials [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021)]. Tantalum, like niobium, has proven utility as the primary superconducting layer within highly coherent qubits [Place et al., Nat. Commun. 12(1), 1–6 (2021) and Wang et al., npj Quantum Inf. 8(1), 1–6 (2022)]. However, unlike Nb, high temperatures are typically used to stabilize the desirable body-centered-cubic phase, α-Ta, during thin film deposition. It has long been known that a thin Nb layer permits the room-temperature nucleation of α-Ta [Westwood et al., Tantalum Thin Films (Academic Press, 1975); D. W. Face and D. E. Prober, J. Vac. Sci. Technol. A 5, 3408–3408 (1987); and Colin et al., Acta Mater. 126, 481–493 (2017)], but here we observe the epitaxial process and present few-photon microwave loss measurements in Nb-nucleated Ta films. We compare resonators patterned from Ta films grown at high temperature (500 °C) and films nucleated at room temperature, in order to understand the impact of the crystalline order on quantum coherence. In both cases, films grew with Al2O3 (001) ǁ Ta (110), indicating that the epitaxial orientation is independent of temperature and is preserved across the Nb/Ta interface. We use conventional low-power spectroscopy to measure two level system (TLS) loss as well as an electric-field bias technique to measure the effective dipole moments of TLS in the surfaces of resonators. In our measurements, Nb-nucleated Ta resonators had greater loss tangent (1.5 ± 0.1 × 10−5) than non-nucleated (5 ± 1 × 10−6) in approximate proportion to defect densities as characterized by x-ray diffraction (0.27° vs 0.18° [110] reflection width) and electron microscopy (30 vs 70 nm domain size). The dependence of the loss tangent on domain size indicates that the development of more ordered Ta films is likely to lead to improvements in qubit coherence times [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021) and Premkumar et al., Commun. Mater. 2(1), 1–9 (2021)]. Moreover, low-temperature α-Ta epitaxy may enable the growth of microstate-free heterostructures, which would not withstand high temperature processing [McSkimming et al., J. Vac. Sci. Technol. A 35, 021401 (2017)].
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.
Tantalum (Ta) is a promising material for reaching long coherence times in superconducting qubits. A detailed understanding of the underlying structure-property relationship remains elusive though. In the present study, we sputter-deposited 200 nm thick Ta films on high-resistivity silicon (100) substrates at temperatures ranging from T = 20°C to 600°C, as well as on different seed layers (Nb, TiN and TaN). Alpha-Ta thin films were readily obtained at temperatures above 500°C and on all seed layers. The films were characterized in terms of surface morphology, residual-resistance ratio, crystal phase composition and superconducting transition temperature, as well as RF-performance using coplanar waveguide resonators. Internal quality factors of up to 1.5 million were measured at 100 mK in the single-photon regime. Despite similar bulk material properties, alpha-Ta films on different seed layers exhibit markedly different RF-performance, which we attribute to dissimilar strain and structural defects at the substrate-metal interfaces. Williamson-Hall analysis of XRD data reveals a clear correlation between decreasing microstrain and increasing quality factor. Cross-sectional HR-TEM further supports this interpretation by directly resolving interfacial disorder. Our results highlight the critical role of interface engineering in optimizing superconducting thin films for low-loss quantum computing circuitry.
Polycrystalline α-tantalum (110) films deposited on the c-plane sapphire substrate by sputtering are used in superconducting qubits nowadays. However, these films always occasionally form other structures, such as α-tantalum (111) grains and β-tantalum grains. To improve the film quality, we investigate the growth of α-tantalum (110) films on the a-plane sapphire substrate under varying conditions by molecular beam epitaxy technology. The optimized α-tantalum (110) film is a single crystal, with a smooth surface and atomically flat metal–substrate interface. The film with thickness of 30 nm shows a Tc of 4.12 K and a high residual resistance ratio of 9.53. The quarter wavelength coplanar waveguide resonators fabricated with the 150 nm optimized α-tantalum (110) film exhibit intrinsic quality factor of over one million under single photon excitation at millikelvin temperature.
Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide.
We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.