Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2301.10306 · Applied Physics Letters

Two-level systems in nucleated and non-nucleated epitaxial alpha-tantalum films

Loren D. Alegria, Daniel Tennant, Kevin Chaves, Jonathan R. I. Lee, Sean R. O’Kelley, Yaniv Jacob Rosen, Jonathan L. DuBois

Published Aug 7, 2023• 19 citations
arXivHTMLPDF

Abstract

Building usefully coherent superconducting quantum processors depends on reducing losses in their constituent materials [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021)]. Tantalum, like niobium, has proven utility as the primary superconducting layer within highly coherent qubits [Place et al., Nat. Commun. 12(1), 1–6 (2021) and Wang et al., npj Quantum Inf. 8(1), 1–6 (2022)]. However, unlike Nb, high temperatures are typically used to stabilize the desirable body-centered-cubic phase, α-Ta, during thin film deposition. It has long been known that a thin Nb layer permits the room-temperature nucleation of α-Ta [Westwood et al., Tantalum Thin Films (Academic Press, 1975); D. W. Face and D. E. Prober, J. Vac. Sci. Technol. A 5, 3408–3408 (1987); and Colin et al., Acta Mater. 126, 481–493 (2017)], but here we observe the epitaxial process and present few-photon microwave loss measurements in Nb-nucleated Ta films. We compare resonators patterned from Ta films grown at high temperature (500 °C) and films nucleated at room temperature, in order to understand the impact of the crystalline order on quantum coherence. In both cases, films grew with Al2O3 (001) ǁ Ta (110), indicating that the epitaxial orientation is independent of temperature and is preserved across the Nb/Ta interface. We use conventional low-power spectroscopy to measure two level system (TLS) loss as well as an electric-field bias technique to measure the effective dipole moments of TLS in the surfaces of resonators. In our measurements, Nb-nucleated Ta resonators had greater loss tangent (1.5 ± 0.1 × 10−5) than non-nucleated (5 ± 1 × 10−6) in approximate proportion to defect densities as characterized by x-ray diffraction (0.27° vs 0.18° [110] reflection width) and electron microscopy (30 vs 70 nm domain size). The dependence of the loss tangent on domain size indicates that the development of more ordered Ta films is likely to lead to improvements in qubit coherence times [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021) and Premkumar et al., Commun. Mater. 2(1), 1–9 (2021)]. Moreover, low-temperature α-Ta epitaxy may enable the growth of microstate-free heterostructures, which would not withstand high temperature processing [McSkimming et al., J. Vac. Sci. Technol. A 35, 021401 (2017)].

DOI
10.1063/5.0157654

Related papers

Interface-sensitive microwave loss in superconducting tantalum films sputtered on c-plane sapphire

Anthony McFadden, Trevyn F. Q. Larson, Stephen Gill +5 more

Quantum coherence in superconducting circuits has increased steadily over the last decades as a result of a growing understanding of the various loss mechanisms. Recently, tantalum (Ta) emerged as a promising material to address microscopic sources of loss found on niobium (Nb) or aluminum (Al) surfaces. However, the effects of film and interface microstructure on low-temperature microwave loss are still not well understood. Here we present a systematic study of the structural and electrical properties of Ta and Nb films sputtered on c-plane sapphire at varying growth temperatures. As growth temperature is increased, our results show that the onset of epitaxial growth of alpha-phase Ta correlates with lower Ta surface roughness, higher critical temperature, and higher residual resistivity ratio, but surprisingly also correlates with a significant increase in loss at microwave frequency. Notably, this high level of loss is not observed in Nb films prepared in the same way and having very similar structure. By experimentally controlling the surface on which the Ta film is nucleated, we determine that the source of loss is only present in samples having an epitaxial Ta/sapphire interface and show that it is apparently mitigated by either growing a thin, epitaxial Nb inter-layer between the Ta film and the substrate or by intentionally treating, and effectively damaging, the sapphire surface with an in-situ argon plasma before Ta growth. In addition to elucidating this interfacial microwave loss, this work provides adequate process details to aid reproducible growth of low-loss Ta films across fabrication facilities.

arXiv:2412.16730•Physical Review Materials•Sep 25, 2025•10 citations

Growth and structure of alpha-Ta films for quantum circuit integration

Loren D. Alegria, Alex Abelson, Eunjeong Kim +5 more

Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.

arXiv:2405.07388•Journal of Applied Physics•Jan 28, 2025•8 citations

Tantalum-Encapsulated Niobium Superconducting Resonators: High Internal Quality Factor and Improved Temporal Stability via Surface Passivation

Anas Alkhazaleh, Juan Villegas, Florent Ravaux +1 more

Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide. We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.

quant-pharXiv:2604.09050•Apr 13, 2026•2 citations

Microwave characterization of tantalum superconducting resonators on silicon substrate with niobium buffer layer

Yoshiro Urade, Kay Yakushiji, Manabu Tsujimoto +4 more

Tantalum thin films sputtered on unheated silicon substrates are characterized with microwaves at around 10 GHz in a 10 mK environment. We show that the phase of tantalum with a body-centered cubic lattice (α-Ta) can be grown selectively by depositing a niobium buffer layer prior to a tantalum film. The physical properties of the films, such as superconducting transition temperature and crystallinity, change markedly with the addition of the buffer layer. Coplanar waveguide resonators based on the composite film exhibit significantly enhanced internal quality factors compared with a film without the buffer layer. The internal quality factor approaches 2 × 107 at a large-photon-number limit. While the quality factor decreases at the single-photon level owing to two-level system (TLS) loss, we have deduced that one of the causes of TLS loss is the amorphous silicon layer at the film–substrate interface, which originates from the substrate cleaning before the film deposition rather than the film itself. The temperature dependence of the internal quality factors shows a marked rise below 200 mK, suggesting the presence of TLS–TLS interactions. The present low-loss tantalum films can be deposited without substrate heating and thus have various potential applications in superconducting quantum electronics.

arXiv:2306.15258•APL Materials•Feb 1, 2024•27 citations

Cryogenic growth of tantalum thin films for low-loss superconducting circuits

Teun A. J. van Schijndel, Anthony McFadden, Aaron N. Engel +5 more

Motivated by recent advancements highlighting $\mathrm{Ta}$ as a promising material in low-loss superconducting circuits and showing long coherence times in superconducting qubits, we have explored the effect of cryogenic temperatures on the growth of $\mathrm{Ta}$ and its integration in superconducting circuits. Cryogenic growth of $\mathrm{Ta}$ using a low-temperature molecular beam epitaxy (MBE) system is found to stabilize single-phase $\ensuremath{\alpha}$-$\mathrm{Ta}$ on several different substrates, which include ${\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)$, $\mathrm{Si}$(001), $\mathrm{Si}$(111), ${\mathrm{Si}\mathrm{N}}_{x}$, and $\mathrm{Ga}\mathrm{As}$(001). The substrates are actively cooled down to cryogenic temperatures and remain 20 K during the $\mathrm{Ta}$ deposition. X-ray $\ensuremath{\theta}$-$2\ensuremath{\theta}$ diffraction (XRD) after warming to room temperature indicates the formation of polycrystalline $\ensuremath{\alpha}$-$\mathrm{Ta}$. The 50-nm $\ensuremath{\alpha}$-$\mathrm{Ta}$ films grown on ${\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)$ at a substrate manipulator temperature of 7 K have a room temperature resistivity (${\ensuremath{\rho}}_{300\phantom{\rule{0.1em}{0ex}}\mathrm{K}}$) of $13.4\phantom{\rule{0.1em}{0ex}}\text{\ensuremath{\mu}}\mathrm{\ensuremath{\Omega}}\phantom{\rule{0.2em}{0ex}}\mathrm{cm}$, a residual resistivity ratio (RRR) of 17.3 and a superconducting transition temperature (${T}_{C}$) of 4.14 K, which are comparable to bulk values. In addition, atomic force microscopy (AFM) indicates that the film grown at 7 K with an rms roughness of 0.45 nm was significantly smoother than the one grown at room temperature. Similar properties are found for films grown on other substrates. Results for films grown at higher substrate manipulator temperatures show higher ${\ensuremath{\rho}}_{300\phantom{\rule{0.1em}{0ex}}\mathrm{K}}$, lower RRR and $\mathrm{Tc}$, and increased $\ensuremath{\beta}$-$\mathrm{Ta}$ content. Coplanar waveguide resonators with a gap width of $3\phantom{\rule{0.1em}{0ex}}\text{\ensuremath{\mu}}\mathrm{m}$ fabricated from cryogenically grown $\mathrm{Ta}$ on $\mathrm{Si}$(111) and ${\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)$ show low-power ${Q}_{i}$ of 1.9 million and 0.7 million, respectively, indicating polycrystalline $\ensuremath{\alpha}$-$\mathrm{Ta}$ films may be promising for superconducting qubit applications even though they are not fully epitaxial.

arXiv:2405.12417•Physical Review Applied•Mar 12, 2025•22 citations

Room temperature pure α-phase tantalum films on sapphire for superconducting qubits

Kunliang Bu, Zhiwen Zong, Zhenxing Zhang +12 more

Abstract Tantalum (Ta) films with a body-centered cubic α-phase play a crucial role in high-performance Ta-based superconducting quantum processors. The growth of pure α-Ta at low temperatures has been a long-term goal. Existing experience with Ta growth on silicon substrates has led to the belief that α-Ta can only be stabilized at high temperatures. In this study, we systematically analyzed the growth mechanism of Ta films on sapphire substrates using first-principles calculations, revealing a narrow growth energy window for pure α-Ta at room temperature (RT). This finding indicates the feasibility of obtaining pure α-Ta at significantly lower temperatures. Experimentally, we successfully achieved pure α-Ta at RT via magnetron sputtering by meticulously adjusting the growth parameters. The resulting superconducting resonators based on the developed RT α-Ta exhibit an internal quality factor ( Q i ) of approximately 2.1 × 10 6 at single-photon levels, comparable to those fabricated at high temperatures. Additionally, fixed-frequency transmon qubits fabricated using the RT α-Ta film demonstrate a coherence time exceeding 280 µs, underscoring the film’s high quality. The RT α-Ta without a seed layer simplifies the fabrication process, offering a more efficient and flexible approach for producing Ta-based superconducting quantum processors.

Superconductor Science and Technology•Jan 15, 2025•3 citations
Building usefully coherent superconducting quantum processors depends on reducing losses in their constituent materials [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021)]. Tantalum, like niobium, has proven utility as the primary superconducting layer within highly coherent qubits [Place et al., Nat. Commun. 12(1), 1–6 (2021) and Wang et al., npj Quantum Inf. 8(1), 1–6 (2022)]. However, unlike Nb, high temperatures are typically used to stabilize the desirable body-centered-cubic phase, α-Ta, during thin film deposition. It has long been known that a thin Nb layer permits the room-temperature nucleation of α-Ta [Westwood et al., Tantalum Thin Films (Academic Press, 1975); D. W. Face and D. E. Prober, J. Vac. Sci. Technol. A 5, 3408–3408 (1987); and Colin et al., Acta Mater. 126, 481–493 (2017)], but here we observe the epitaxial process and present few-photon microwave loss measurements in Nb-nucleated Ta films. We compare resonators patterned from Ta films grown at high temperature (500 °C) and films nucleated at room temperature, in order to understand the impact of the crystalline order on quantum coherence. In both cases, films grew with Al2O3 (001) ǁ Ta (110), indicating that the epitaxial orientation is independent of temperature and is preserved across the Nb/Ta interface. We use conventional low-power spectroscopy to measure two level system (TLS) loss as well as an electric-field bias technique to measure the effective dipole moments of TLS in the surfaces of resonators. In our measurements, Nb-nucleated Ta resonators had greater loss tangent (1.5 ± 0.1 × 10−5) than non-nucleated (5 ± 1 × 10−6) in approximate proportion to defect densities as characterized by x-ray diffraction (0.27° vs 0.18° [110] reflection width) and electron microscopy (30 vs 70 nm domain size). The dependence of the loss tangent on domain size indicates that the development of more ordered Ta films is likely to lead to improvements in qubit coherence times [I. Siddiqi, Nat. Rev. Mater. 6, 875–891 (2021) and Premkumar et al., Commun. Mater. 2(1), 1–9 (2021)]. Moreover, low-temperature α-Ta epitaxy may enable the growth of microstate-free heterostructures, which would not withstand high temperature processing [McSkimming et al., J. Vac. Sci. Technol. A 35, 021401 (2017)].
Quantum coherence in superconducting circuits has increased steadily over the last decades as a result of a growing understanding of the various loss mechanisms. Recently, tantalum (Ta) emerged as a promising material to address microscopic sources of loss found on niobium (Nb) or aluminum (Al) surfaces. However, the effects of film and interface microstructure on low-temperature microwave loss are still not well understood. Here we present a systematic study of the structural and electrical properties of Ta and Nb films sputtered on c-plane sapphire at varying growth temperatures. As growth temperature is increased, our results show that the onset of epitaxial growth of alpha-phase Ta correlates with lower Ta surface roughness, higher critical temperature, and higher residual resistivity ratio, but surprisingly also correlates with a significant increase in loss at microwave frequency. Notably, this high level of loss is not observed in Nb films prepared in the same way and having very similar structure. By experimentally controlling the surface on which the Ta film is nucleated, we determine that the source of loss is only present in samples having an epitaxial Ta/sapphire interface and show that it is apparently mitigated by either growing a thin, epitaxial Nb inter-layer between the Ta film and the substrate or by intentionally treating, and effectively damaging, the sapphire surface with an in-situ argon plasma before Ta growth. In addition to elucidating this interfacial microwave loss, this work provides adequate process details to aid reproducible growth of low-loss Ta films across fabrication facilities.
Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.
Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide. We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.
Tantalum thin films sputtered on unheated silicon substrates are characterized with microwaves at around 10 GHz in a 10 mK environment. We show that the phase of tantalum with a body-centered cubic lattice (α-Ta) can be grown selectively by depositing a niobium buffer layer prior to a tantalum film. The physical properties of the films, such as superconducting transition temperature and crystallinity, change markedly with the addition of the buffer layer. Coplanar waveguide resonators based on the composite film exhibit significantly enhanced internal quality factors compared with a film without the buffer layer. The internal quality factor approaches 2 × 107 at a large-photon-number limit. While the quality factor decreases at the single-photon level owing to two-level system (TLS) loss, we have deduced that one of the causes of TLS loss is the amorphous silicon layer at the film–substrate interface, which originates from the substrate cleaning before the film deposition rather than the film itself. The temperature dependence of the internal quality factors shows a marked rise below 200 mK, suggesting the presence of TLS–TLS interactions. The present low-loss tantalum films can be deposited without substrate heating and thus have various potential applications in superconducting quantum electronics.
Motivated by recent advancements highlighting Ta\mathrm{Ta}Ta as a promising material in low-loss superconducting circuits and showing long coherence times in superconducting qubits, we have explored the effect of cryogenic temperatures on the growth of Ta\mathrm{Ta}Ta and its integration in superconducting circuits. Cryogenic growth of Ta\mathrm{Ta}Ta using a low-temperature molecular beam epitaxy (MBE) system is found to stabilize single-phase $\ensuremath{\alpha}$-Ta\mathrm{Ta}Ta on several different substrates, which include Al2O3(0001){\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)Al2​O3​(0001), Si\mathrm{Si}Si(001), Si\mathrm{Si}Si(111), SiNx{\mathrm{Si}\mathrm{N}}_{x}SiNx​, and GaAs\mathrm{Ga}\mathrm{As}GaAs(001). The substrates are actively cooled down to cryogenic temperatures and remain 20 K during the Ta\mathrm{Ta}Ta deposition. X-ray $\ensuremath{\theta}$-$2\ensuremath{\theta}$ diffraction (XRD) after warming to room temperature indicates the formation of polycrystalline $\ensuremath{\alpha}$-Ta\mathrm{Ta}Ta. The 50-nm $\ensuremath{\alpha}$-Ta\mathrm{Ta}Ta films grown on Al2O3(0001){\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)Al2​O3​(0001) at a substrate manipulator temperature of 7 K have a room temperature resistivity (${\ensuremath{\rho}}_{300\phantom{\rule{0.1em}{0ex}}\mathrm{K}}$) of $13.4\phantom{\rule{0.1em}{0ex}}\text{\ensuremath{\mu}}\mathrm{\ensuremath{\Omega}}\phantom{\rule{0.2em}{0ex}}\mathrm{cm}$, a residual resistivity ratio (RRR) of 17.3 and a superconducting transition temperature (TC{T}_{C}TC​) of 4.14 K, which are comparable to bulk values. In addition, atomic force microscopy (AFM) indicates that the film grown at 7 K with an rms roughness of 0.45 nm was significantly smoother than the one grown at room temperature. Similar properties are found for films grown on other substrates. Results for films grown at higher substrate manipulator temperatures show higher ${\ensuremath{\rho}}_{300\phantom{\rule{0.1em}{0ex}}\mathrm{K}}$, lower RRR and Tc\mathrm{Tc}Tc, and increased $\ensuremath{\beta}$-Ta\mathrm{Ta}Ta content. Coplanar waveguide resonators with a gap width of $3\phantom{\rule{0.1em}{0ex}}\text{\ensuremath{\mu}}\mathrm{m}$ fabricated from cryogenically grown Ta\mathrm{Ta}Ta on Si\mathrm{Si}Si(111) and Al2O3(0001){\mathrm{Al}}_{2}{\mathrm{O}}_{3}(0001)Al2​O3​(0001) show low-power Qi{Q}_{i}Qi​ of 1.9 million and 0.7 million, respectively, indicating polycrystalline $\ensuremath{\alpha}$-Ta\mathrm{Ta}Ta films may be promising for superconducting qubit applications even though they are not fully epitaxial.
Abstract Tantalum (Ta) films with a body-centered cubic α-phase play a crucial role in high-performance Ta-based superconducting quantum processors. The growth of pure α-Ta at low temperatures has been a long-term goal. Existing experience with Ta growth on silicon substrates has led to the belief that α-Ta can only be stabilized at high temperatures. In this study, we systematically analyzed the growth mechanism of Ta films on sapphire substrates using first-principles calculations, revealing a narrow growth energy window for pure α-Ta at room temperature (RT). This finding indicates the feasibility of obtaining pure α-Ta at significantly lower temperatures. Experimentally, we successfully achieved pure α-Ta at RT via magnetron sputtering by meticulously adjusting the growth parameters. The resulting superconducting resonators based on the developed RT α-Ta exhibit an internal quality factor ( Q i ) of approximately 2.1 × 10 6 at single-photon levels, comparable to those fabricated at high temperatures. Additionally, fixed-frequency transmon qubits fabricated using the RT α-Ta film demonstrate a coherence time exceeding 280 µs, underscoring the film’s high quality. The RT α-Ta without a seed layer simplifies the fabrication process, offering a more efficient and flexible approach for producing Ta-based superconducting quantum processors.