Josephson element-based parametric amplifiers (JPAs) typically require rf pump power that is several orders of magnitude stronger than the maximum signal power they can handle. The low power efficiency and strong pump leakage towards signal circuitry could be critical concerns in application. In this work, we discuss how to optimize the pump coupling scheme for a three-wave mixing JPA by employing microwave filtering techniques, with the goal of maximizing the pump power efficiency and minimize pump leakage without sacrificing other properties of interest. We implement the corresponding filter design in a SNAIL-based JPA and demonstrate more than three orders of magnitude improvement in both power efficiency and pump leakage suppression compared to a similar device with regular capacitive coupling, while maintaining state-of-the-art dynamic range and near-quantum-limited noise performance. Furthermore, we show experimentally that the filter-coupled JPA is more robust against noise input from the pump port, exhibiting no significant change in added noise performance with up to 4 K of effective noise temperature at the pump port.
Josephson element-based parametric amplifiers (JPAs) typically require rf pump power that is several orders of magnitude stronger than the maximum signal power they can handle. The low power efficiency and strong pump leakage towards signal circuitry could be critical concerns in application. In this work, we discuss how to optimize the pump coupling scheme for a three-wave mixing JPA by employing microwave filtering techniques, with the goal of maximizing the pump power efficiency and minimize pump leakage without sacrificing other properties of interest. We implement the corresponding filter design in a SNAIL-based JPA and demonstrate more than three orders of magnitude improvement in both power efficiency and pump leakage suppression compared to a similar device with regular capacitive coupling, while maintaining state-of-the-art dynamic range and near-quantum-limited noise performance. Furthermore, we show experimentally that the filter-coupled JPA is more robust against noise input from the pump port, exhibiting no significant change in added noise performance with up to 4 K of effective noise temperature at the pump port.
Superconducting quantum circuits are a leading platform for building a large-scale quantum processor [1]. A crucial component necessary for the high-fidelity readout of qubits in this framework, is an ultra-low-noise microwave amplifier. Thus, over the past two decades, superconducting Josephson parametric amplifiers (JPAs) have been developed that achieve near quantum-limited noise performance, an order of magnitude lower than competing microwave amplifiers based on semiconductor transistors [2]. Nevertheless, JPAs suffer from drawbacks such as limited bandwidth and compression power that makes them difficult to use in an eventual large-scale quantum processor. Thus, an ongoing theme in JPA development is to optimize the circuit to improve these specifications without sacrificing other desirable properties such as the noise performance, ease of construction and operation, etc. Here, we review some results of optimizing a specific JPA circuit called the SNAIL parametric amplifier [3]–[5], shown in Fig. 1, where the acronym SNAIL refers to the Superconducting Nonlinear Asymmetric Inductive eLement. The SNAIL is a composite element made from conventional Al/AlOx/Al Josephson junctions, which has a nonlinear current-phase relation that can be approximated as a nonlinear inductance. By applying a strong microwave frequency pump to modulate the nonlinear inductance, parametric amplification can be realized. By device and circuit engineering we have demonstrated two orders of magnitude improvement in compression power (Fig. 2) in such devices without sacrificing other desirable characteristics.
Circuit quantum-electrodynamics-based quantum information processing relies on low noise amplification for signal readout. In the realm of microwave superconducting circuits, this amplification is often achieved via Josephson parametric amplifiers (JPAs). In the past, these amplifiers exhibited low power added efficiency (PAE), which is roughly the fraction of pump power that is converted to output signal power. This is increasingly relevant because recent attempts to build high saturation power amplifiers achieve this at the cost of very low PAE, which in turn puts a high heat load on the cryostat and limits the number of these devices that a dilution refrigerator can host. Here, we numerically investigate upper bounds on PAE. We focus on a class of parametric amplifiers that consists of a capacitor shunted by a nonlinear inductive block. We first set a benchmark for this class of amplifiers by considering nonlinear blocks described by an arbitrary polynomial current-phase relation. Next, we identify that it is important for amplifiers with inductive blocks composed of repeating elements to have monotonic current-phase relations for each element in order to avoid exciting high-frequency modes. Using this design rule, we propose two circuit implementations for repeating elements in JPA inductive blocks. Finally, we investigate polynomial amplifier chains. We find that while amplifiers with higher gain have a lower PAE, regardless of the gain there is considerable room to improve as compared with state-of-the-art devices. For example, for a degenerate amplifier with a power gain of 20 dB, the PAE is $\ensuremath{\approx}0.1%$ for typical JPAs, 37.9% for our simpler circuit JPAs, 42.6% for our more complex circuit JPAs, 63.3% for our arbitrary polynomial amplifiers, and at least 98% for our amplifier chains.
Josephson parametric amplifiers (JPA) are nonlinear devices that are used for quantum sensing and qubit readout in the microwave regime. While JPAs regularly operate near the quantum limit, their gain saturates for very small (few-photon) input power. In a previous work, we showed that the saturation power of JPAs is not limited by pump depletion, but instead by the fourth-order nonlinearity of Josephson junctions, the nonlinear circuit elements that enables amplification in JPAs. Here, we present a systematic study of the nonlinearities in JPAs, show which nonlinearities limit the saturation power, and present a strategy for optimizing the circuit parameters for achieving the best possible JPA. For concreteness, we focus on JPAs that are constructed around a Josephson ring modulator (JRM). We show that by tuning the external and shunt inductors, we should be able to take the best experimentally available JPAs and improve their saturation power by $\ensuremath{\approx}15\phantom{\rule{0.16em}{0ex}}\mathrm{dB}$. Finally, we argue that our methods and qualitative results are applicable to a broad range of cavity-based JPAs.
Quantum-limited Josephson parametric amplifiers are a key component in many precision microwave measurement setups, such as for the readout of superconducting qubits in a quantum computer. As qubit setups scale up, these amplifiers must be optimized to handle input signals of ever-larger power. The authors design a quantum-limited parametric amplifier based on an array of superconducting nonlinear asymmetric inductive elements. This ``SNAIL'' is optimized to handle large input signals without sacrificing other desirable characteristics. The method can be extended to improve all forms of parametrically induced mixing in quantum information applications.
Low-noise microwave amplifiers are crucial for detecting weak signals in fields such as quantum technology and radio astronomy. However, designing an ideal amplifier is challenging, as it must cover a wide frequency range, add minimal noise, and operate directionally - amplifying signals only in the observer's direction while protecting the source from environmental interference. In this work, we demonstrate that an array of non-linearly coupled Josephson parametric amplifiers (JPAs) can collectively function as a directional, broadband quantum amplifier by harnessing topological effects. By applying a collective four-wave-mixing pump with inhomogeneous amplitudes and linearly increasing phase, we break time-reversal symmetry in the JPA array and stabilize a topological amplification regime where signals are exponentially amplified in one direction and exponentially suppressed in the opposite. We show that compact devices with few sites N∼11−17 can achieve exceptional performance, with gains exceeding 20 dB over a bandwidth ranging from hundreds of MHz to GHz, and reverse isolation suppressing backward noise by more than 30 dB across all frequencies. The device also operates near the quantum noise limit and provides topological protection against up to 15% fabrication disorder, effectively suppressing gain ripples. The amplifier's intrinsic directionality eliminates the need for external isolators, paving the way for fully on-chip, near-ideal superconducting pre-amplifiers.
Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.