Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2408.11807 · Physical Review Applied

Low-noise microwave parametric amplifier based on self-heated nonlinear impedance with subnanosecond thermal response

Michael Will, Mohammad Tasnimul Haque, Yuvraj Chaudhry, Dmitry S. Golubev, Pertti Juhani Hakonen

Published Jan 17, 2025• 0 citations
arXivHTMLPDF

Abstract

Low-noise amplifiers are of great significance in the field of quantum technologies. We study a thermally driven parametric amplifier based on a superconductor-insulator-graphene-insulator-superconductor ($S$-$I$-$G$-$I$-$S$) junction coupled to a superconducting microwave cavity. The strong nonlinearity in the temperature dependence of our device leads to thermal self-modulation that produces impedance oscillations at frequencies around twice the angular cavity resonance frequency ${\ensuremath{\omega}}_{\mathrm{r}}$. In particular, reactance modulation of the effective capacitance yields a gain of 18.6 dB over a frequency span of 125 kHz with a minimum noise temperature of ${T}_{\mathrm{N}}=1.4\phantom{\rule{0.2em}{0ex}}\mathrm{K}$. Our theoretical modeling gives insight into the exact mixing processes, confirmation of the electron-phonon coupling parameter and possible improvements of the studied system.

DOI
10.1103/physrevapplied.23.014037

Related papers

Low noise microwave parametric amplifier

A. D. Smith, Robert D. Sandell, John F. Burch +1 more

We report the lowest noise temperature of any microwave amplifier except the maser. This amplifier is a nearly degenerate superconducting parametric amplifier at X-band consisting of a low β, thin film, single junction SQUID, a monolithic 50 Ω to 1 Ω impedance matching network, and a cooled circulator. Nb/Nb2O5/Pb alloy junctions were incorporated into Nb and Pb-in circuitry on 1×2 cm silicon chips. The SQUID was phase-biased near 90° and driven by an external pump at approximately twice the operating frequency. The self-resonance frequency of the SQUID inductance and junction capacitance was set at the operating frequency of 8.2GHz. The operating charac teristics depended on the pump amplitude, the junction phase bias, and the SQUID parameters. For small values of\beta < 1, the maximum gain in both the signal and idler channels was ≈10dB, the bandwidth = 170MHz, and the single-sidehand noise temperature was 6K with an uncertainty of (+15 to -7)K. For higher β, the gain increased to nearly 30dB with increased noise and parametric oscillations occurring near the pump subharmonic frequency.

IEEE Transactions on Magnetics•Mar 1, 1985•40 citations

Parametric Microwave Amplification using a Tunable Superconducting Resonator

C. W. Sandbo Chang

In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.

•Sep 2, 2015•0 citations

Low noise parametric upconversion with a self-pumped Josephson junction

Helmut Kanter

Experimental results are reported on a Josephson parametric upconverting amplifier which is self-pumped via the internal Josephson oscillations derived from a dc bias voltage. A niobium point-contact SQUID is simultaneously coupled to a 115-MHz tank circuit and a 9-GHz cavity. Josephson oscillations at 9 GHz produce parametric upconversion of power in the 115-MHz circuit to sidebands at 9±0.115 GHz with measured power gain of 25. The amplifier noise temperature, referred to the input at 115 MHz, was established to be <15 K by varying the temperature of an input termination from 4.2 to 300 K. This result establishes the behavior of self-pumped SQUID upconverters at microwave frequencies and demonstrates that the achievable noise performance is not greatly in excess of the thermal limit.

Journal of Applied Physics•May 1, 1975•3 citations

Shunted Josephson tunnel junctions: High-frequency, self-pumped low noise amplifiers

Nils P. Calander, T. Claeson, S. Rudner

The high-frequency amplification properties of transformer coupled, resistively shunted Josephson tunnel junctions have been investigated. The importance of the shunt loop inductance is stressed. It allows a high cutoff frequency, of significance for good high-frequency performance. The self-pumped parametric amplifier showed none of the excessive noise rise, which has hitherto plagued the development of externally pumped Josephson junction amplifiers. Around 10 GHz, we estimated a noise temperature less than 30 K for an amplifier pumped by a Josephson oscillation with a frequency well above twice the signal frequency. The corresponding gain of 5 dB may be increased in a better impedance matched circuit. The gain was very stable against variations in the bias conditions. A gain-bandwidth product as high as 0.3 was registered. The experimental results agreed well with the established theory for self-pumped parametric Josephson amplifiers. It should be possible to extend the low noise amplification by this device to mm wave frequencies. A relaxation oscillation occurred at a subharmonic of the Josephson frequency when the shunt loop inductance became large. The amplification in this mode followed closely the predictions of a simple model, where the signal modulated the switching of the sawtooth-like (relatively low frequency) relaxation current. Gains of about 15 dB were measured around 10 GHz, but the amplification was sensitive to bias conditions and noisy in this case where the relaxation frequency fell well below the signal frequency. Much improved properties were registered when the inductance was decreased so that the relaxation frequency approached the Josephson frequency and exceeded twice the signal frequency. The behavior then resembled that of a Josephson mode parametric amplifier, but the high content of harmonics of a relaxation oscillation meant that the amplifier became noisier due to converted noise from the many idler frequencies.

Journal of Applied Physics•Jul 1, 1982•26 citations

One-frequency parametric amplifier using self-pumped Josephson junction

Alexander N. Vystavkin, V. Gubankov, L. S. Kuzmin +3 more

Gain and noise properties of a non-degenerate one-frequency parametric amplifier using a self-pumped Josephson junction are investigated both theoretically and experimentally. The amplifier uses the phenomenon of microwave negative resistance of the junction. Theoretical analysis made in usual resistively shunted junction (RSJ) model shows that the minimum noise temperature is equal to approximately 42T. It takes place at a signal frequency f close to the junction characteristic frequency f0. Maximum effectivity (the product of the square root of power gain and relative bandwidth) can reach 0.4 at f≃f0. Gain up to 20 dB was obtained at X-band using amplifier with Nb-Ta point-contact junction. Minimum noise temperature at T = 4.2K was about 200K.

IEEE Transactions on Magnetics•Jan 1, 1977•16 citations

Demonstration of SQUID (Superconducting QUantum Interference Device) parametric amplifier

Arnold H. Silver, R. Sandell, Reggie Phillips +1 more

This is the first Annual Report of an effort to demonstrate a low noise superconducting microwave amplifier. The amplifier is a nearly degenerate, single idler parametric amplifier which uses the nonlinear inductance of a single junction SQUID (Superconducting Quantum Interference Device). The design frequency is 9 GHz, 10 dB gain, and 16% bandwidth. In order to maximize the saturation power, the device impedance was chosen near 1ohm and a matching network was designed to transform to 50ohm. In later designs, a coherent array of SQUIDs is expected to increase the power and impedance. This report includes the design and test of the 50ohm to 1ohm broadband transformer, design and fabrication of the SQUID amplifier, and both saturation and noise analyses of the single SQUID and SQUID array. The analytical results, reported to the 1982 Applied Superconductivity Conference are: the noise temperature of the single SQUID parametric amplifier is equal to the amplifier termination temperature T(o), the response is linear to several percent of the flux quantum energy in the SQUID: the amplifier will be saturated by broad band noise if the noise source temperature is much greater than 10 To; and the array parametric amplifier has the same noise temperature as the single device indicating an N-fold increase in dynamic range. (Author)

Annual Report•Nov 1, 1982•0 citations
Low-noise amplifiers are of great significance in the field of quantum technologies. We study a thermally driven parametric amplifier based on a superconductor-insulator-graphene-insulator-superconductor (SSS-III-GGG-III-SSS) junction coupled to a superconducting microwave cavity. The strong nonlinearity in the temperature dependence of our device leads to thermal self-modulation that produces impedance oscillations at frequencies around twice the angular cavity resonance frequency \ensuremathωr{\ensuremath{\omega}}_{\mathrm{r}}\ensuremathωr​. In particular, reactance modulation of the effective capacitance yields a gain of 18.6 dB over a frequency span of 125 kHz with a minimum noise temperature of TN=1.4K{T}_{\mathrm{N}}=1.4\phantom{\rule{0.2em}{0ex}}\mathrm{K}TN​=1.4K. Our theoretical modeling gives insight into the exact mixing processes, confirmation of the electron-phonon coupling parameter and possible improvements of the studied system.
We report the lowest noise temperature of any microwave amplifier except the maser. This amplifier is a nearly degenerate superconducting parametric amplifier at X-band consisting of a low β, thin film, single junction SQUID, a monolithic 50 Ω to 1 Ω impedance matching network, and a cooled circulator. Nb/Nb2O5/Pb alloy junctions were incorporated into Nb and Pb-in circuitry on 1×2 cm silicon chips. The SQUID was phase-biased near 90° and driven by an external pump at approximately twice the operating frequency. The self-resonance frequency of the SQUID inductance and junction capacitance was set at the operating frequency of 8.2GHz. The operating charac teristics depended on the pump amplitude, the junction phase bias, and the SQUID parameters. For small values of\beta < 1, the maximum gain in both the signal and idler channels was ≈10dB, the bandwidth = 170MHz, and the single-sidehand noise temperature was 6K with an uncertainty of (+15 to -7)K. For higher β, the gain increased to nearly 30dB with increased noise and parametric oscillations occurring near the pump subharmonic frequency.
In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.
Experimental results are reported on a Josephson parametric upconverting amplifier which is self-pumped via the internal Josephson oscillations derived from a dc bias voltage. A niobium point-contact SQUID is simultaneously coupled to a 115-MHz tank circuit and a 9-GHz cavity. Josephson oscillations at 9 GHz produce parametric upconversion of power in the 115-MHz circuit to sidebands at 9±0.115 GHz with measured power gain of 25. The amplifier noise temperature, referred to the input at 115 MHz, was established to be <15 K by varying the temperature of an input termination from 4.2 to 300 K. This result establishes the behavior of self-pumped SQUID upconverters at microwave frequencies and demonstrates that the achievable noise performance is not greatly in excess of the thermal limit.
The high-frequency amplification properties of transformer coupled, resistively shunted Josephson tunnel junctions have been investigated. The importance of the shunt loop inductance is stressed. It allows a high cutoff frequency, of significance for good high-frequency performance. The self-pumped parametric amplifier showed none of the excessive noise rise, which has hitherto plagued the development of externally pumped Josephson junction amplifiers. Around 10 GHz, we estimated a noise temperature less than 30 K for an amplifier pumped by a Josephson oscillation with a frequency well above twice the signal frequency. The corresponding gain of 5 dB may be increased in a better impedance matched circuit. The gain was very stable against variations in the bias conditions. A gain-bandwidth product as high as 0.3 was registered. The experimental results agreed well with the established theory for self-pumped parametric Josephson amplifiers. It should be possible to extend the low noise amplification by this device to mm wave frequencies. A relaxation oscillation occurred at a subharmonic of the Josephson frequency when the shunt loop inductance became large. The amplification in this mode followed closely the predictions of a simple model, where the signal modulated the switching of the sawtooth-like (relatively low frequency) relaxation current. Gains of about 15 dB were measured around 10 GHz, but the amplification was sensitive to bias conditions and noisy in this case where the relaxation frequency fell well below the signal frequency. Much improved properties were registered when the inductance was decreased so that the relaxation frequency approached the Josephson frequency and exceeded twice the signal frequency. The behavior then resembled that of a Josephson mode parametric amplifier, but the high content of harmonics of a relaxation oscillation meant that the amplifier became noisier due to converted noise from the many idler frequencies.
Gain and noise properties of a non-degenerate one-frequency parametric amplifier using a self-pumped Josephson junction are investigated both theoretically and experimentally. The amplifier uses the phenomenon of microwave negative resistance of the junction. Theoretical analysis made in usual resistively shunted junction (RSJ) model shows that the minimum noise temperature is equal to approximately 42T. It takes place at a signal frequency f close to the junction characteristic frequency f0. Maximum effectivity (the product of the square root of power gain and relative bandwidth) can reach 0.4 at f≃f0. Gain up to 20 dB was obtained at X-band using amplifier with Nb-Ta point-contact junction. Minimum noise temperature at T = 4.2K was about 200K.
This is the first Annual Report of an effort to demonstrate a low noise superconducting microwave amplifier. The amplifier is a nearly degenerate, single idler parametric amplifier which uses the nonlinear inductance of a single junction SQUID (Superconducting Quantum Interference Device). The design frequency is 9 GHz, 10 dB gain, and 16% bandwidth. In order to maximize the saturation power, the device impedance was chosen near 1ohm and a matching network was designed to transform to 50ohm. In later designs, a coherent array of SQUIDs is expected to increase the power and impedance. This report includes the design and test of the 50ohm to 1ohm broadband transformer, design and fabrication of the SQUID amplifier, and both saturation and noise analyses of the single SQUID and SQUID array. The analytical results, reported to the 1982 Applied Superconductivity Conference are: the noise temperature of the single SQUID parametric amplifier is equal to the amplifier termination temperature T(o), the response is linear to several percent of the flux quantum energy in the SQUID: the amplifier will be saturated by broad band noise if the noise source temperature is much greater than 10 To; and the array parametric amplifier has the same noise temperature as the single device indicating an N-fold increase in dynamic range. (Author)