Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Parametric Microwave Amplification using a Tunable Superconducting Resonator

C. W. Sandbo Chang

Published Sep 2, 2015• 0 citations
OpenAlex

Abstract

In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.

Related papers

Parametrically pumped superconducting circuits

Philip Krantz

In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model $-$ the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.

•Jan 1, 2013•1 citation

Flux-driven Josephson parametric amplifier

Tsuyoshi Yamamoto, K. Inomata, 道生 渡部 +5 more

We have developed a Josephson parametric amplifier comprising a superconducting coplanar-waveguide resonator terminated by a dc superconducting quantum interference device (SQUID). An external field (the pump, ∼20 GHz) modulates the flux threading of the dc SQUID and, therefore, the resonant frequency of the cavity field (the signal, ∼10 GHz), which leads to the parametric signal amplification. We operated the amplifier at different band centers and observed amplification (17 dB at maximum) and deamplification depending on the relative phase between the pump and the signal. The noise temperature is estimated to be less than 0.87 K.

arXiv:0808.1386•Applied Physics Letters•Jul 28, 2008•485 citations

Parametric interactions with signals and the vacuum

Michaël Simoen

In this thesis I present different experiments on superconducting circuits exploring parametric interactions with external signals and the vacuum in the microwave regime. These parametric processes are the result of the periodic modulation of a property of a system which results in different interactions. The systems used in this thesis are circuits where the nonlinear inductance of a superconducting quantum interference device (SQUID) is parametrically driven.I present the first experimental observation of the dynamical Casimir effect (DCE), since it was predicted in 1970. The DCE is an interaction between the vacuum and a periodically modulated boundary condition of the electromagnetic field, here implemented by a flux-tuned SQUID. In essence the modulated boundary will parametrically amplify the vacuum fluctuations which results in the pairwise generation of photons over a broad frequency range. I have characterized the system and measured the statistical properties of the emitted radiation to show that the radiation exhibits two-mode squeezing.Next, I present measurements on a superconducting multimode resonator containing a SQUID. I show that it is possible to get parametric amplification by driving the SQUID at either twice the frequency of one of the modes or by driving it at the sum of two mode frequencies. In both cases I show that it is possible to reach quantum-limited noise performance.In the same system I also demonstrate frequency conversion which occurs when the system is pumped at the difference frequency between two modes. Microwave photons are coherently transferred from one mode to the other. I show that the coupling strength depends linearly on the applied pump amplitude.The thesis also contains a linearized theoretical model to describe and analyze the flux-pumped SQUID. The model describes an equivalent circuit element called the pumpistor, with an impedance which depends on the pump phase. I show that under specific conditions the impedance becomes real and negative allowing pump power to be injected into the circuit, providing gain.Finally I also present a demonstration of an on-chip Mach-Zehnder interferometer. This experiment uses the tunability of the SQUID to provide a controllable phase shift in one of the interferometer arms. The transmission through the device can be modulated with a maximum change of 45 dB.

•Jan 1, 2015•4 citations

Nonlinearity and parametric driving in a SQUID-tunable microchip resonator

Yarema Reshitnyk

Advances in the field of nanoscale quantum engineered systems depend crucially on the ability to make quantum limited measurements. Current capabilities are limited by technical and quantum noise introduced by devices used for transduction and amplification of the inherently small signals of interest. Many experimental implementations, including nano-mechanical systems, solid-state quantum bits (qubits), and circuit quantum-electrodynamics (c-QED) devices, utilize transmitted or reflected microwave signals to measure the field quadratures of signals composed of few photons. Traditional low-noise cryogenic HEMT amplifiers provide an unsatisfactory solution to this quantum measurement problem because the targeted signal is often much smaller than the added noise. In principle, c-QED devices can be used for quantum-limited amplification, particularly as a parametric amplifier (PA). An ideal parametric amplifier should amplify signals without introducing additional noise, which would allow for the attainment of quantum feedback algorithms. In this thesis, I describe the characterization of a c-QED device, known as a tunable resonator, with the goal of quantifying its limits when used as a parametric amplifier. Tunable resonators are currently being used as PAs in quantum limited experiments, however, some of the underlying dynamics of these devices have not yet been fully characterized. I investigated the frequency, internal loss, power dependent frequency shift (nonlinearity) of a tunable microwave co-planar waveguide (CPW) resonator as a function of external magnetic flux biasing, which changes the effective length of the resonator. By looking at multiple samples with different design parameters, I observed that nonlinear damping is inherent to this device. Nonlinear damping had previously been observed but not described in sufficient detail to provide insight into its origins, which may explain some underlying dynamics of the tunable resonator. My measurements of the nonlinear damping shows that at larger flux biases, the nonlinear damping dominates linear internal losses and represent the main contribution to the total internal loss rate. I then operated this device as a parametric oscillator (PO) and found that the nonlinear damping and large Kerr (or quartic) nonlinearity likely cause an increase in the above-threshold switching rates between π-phase shifted steady states, which in turn may be associated with anomalous above-threshold squeezing in these devices. The results of my thesis show that nonlinear damping is present in these devices and affects performance in them dearly. This result is important for future work in PAs as improved understanding of the nonlinear damping will enable engineering of a device which can act as a PA with maximal gain and minimum noise.

•Jan 1, 2014•0 citations

High-gain weakly nonlinear flux-modulated Josephson parametric amplifier using a SQUID array

Xin Zhou, Vivien Schmitt, Patrice Bertet +4 more

We have developed and measured a high-gain quantum-limited microwave parametric amplifier based on a superconducting lumped LC resonator with the inductor L including an array of eight superconducting quantum interference devices (SQUIDs). This amplifier is parametrically pumped by modulating the flux threading the SQUIDs at twice the resonator frequency. Around 5 GHz, a maximum gain of 31 dB, a product amplitude gain $\ifmmode\times\else\texttimes\fi{}$ bandwidth above 60 MHz, and a 1 dB compression point of $\ensuremath{-}123$ dBm at 20 dB gain are obtained in the nondegenerate mode of operation. Phase-sensitive amplification-deamplification is also measured in the degenerate mode and yields a maximum gain of 37 dB. The compression point obtained is 18 dB above what would be obtained with a single SQUID of the same inductance, due to the smaller nonlinearity of the SQUID array.

arXiv:1409.5630•Physical Review B•Jun 30, 2014•101 citations

Characterization of a multimode coplanar waveguide parametric amplifier

M. Simoen, C. W. S. Chang, Philip Krantz +5 more

We characterize a Josephson parametric amplifier based on a flux-tunable quarter-wavelength resonator. The fundamental resonance frequency is ∼1 GHz, but we use higher modes of the resonator for our measurements. An on-chip tuning line allows for magnetic flux pumping of the amplifier. We investigate and compare degenerate parametric amplification, involving a single mode, and nondegenerate parametric amplification, using a pair of modes. We show that we reach quantum-limited noise performance in both cases.

arXiv:1409.8160•Journal of Applied Physics•Oct 16, 2015•49 citations
In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.
In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model −-− the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.
We have developed a Josephson parametric amplifier comprising a superconducting coplanar-waveguide resonator terminated by a dc superconducting quantum interference device (SQUID). An external field (the pump, ∼20 GHz) modulates the flux threading of the dc SQUID and, therefore, the resonant frequency of the cavity field (the signal, ∼10 GHz), which leads to the parametric signal amplification. We operated the amplifier at different band centers and observed amplification (17 dB at maximum) and deamplification depending on the relative phase between the pump and the signal. The noise temperature is estimated to be less than 0.87 K.
In this thesis I present different experiments on superconducting circuits exploring parametric interactions with external signals and the vacuum in the microwave regime. These parametric processes are the result of the periodic modulation of a property of a system which results in different interactions. The systems used in this thesis are circuits where the nonlinear inductance of a superconducting quantum interference device (SQUID) is parametrically driven.I present the first experimental observation of the dynamical Casimir effect (DCE), since it was predicted in 1970. The DCE is an interaction between the vacuum and a periodically modulated boundary condition of the electromagnetic field, here implemented by a flux-tuned SQUID. In essence the modulated boundary will parametrically amplify the vacuum fluctuations which results in the pairwise generation of photons over a broad frequency range. I have characterized the system and measured the statistical properties of the emitted radiation to show that the radiation exhibits two-mode squeezing.Next, I present measurements on a superconducting multimode resonator containing a SQUID. I show that it is possible to get parametric amplification by driving the SQUID at either twice the frequency of one of the modes or by driving it at the sum of two mode frequencies. In both cases I show that it is possible to reach quantum-limited noise performance.In the same system I also demonstrate frequency conversion which occurs when the system is pumped at the difference frequency between two modes. Microwave photons are coherently transferred from one mode to the other. I show that the coupling strength depends linearly on the applied pump amplitude.The thesis also contains a linearized theoretical model to describe and analyze the flux-pumped SQUID. The model describes an equivalent circuit element called the pumpistor, with an impedance which depends on the pump phase. I show that under specific conditions the impedance becomes real and negative allowing pump power to be injected into the circuit, providing gain.Finally I also present a demonstration of an on-chip Mach-Zehnder interferometer. This experiment uses the tunability of the SQUID to provide a controllable phase shift in one of the interferometer arms. The transmission through the device can be modulated with a maximum change of 45 dB.
Advances in the field of nanoscale quantum engineered systems depend crucially on the ability to make quantum limited measurements. Current capabilities are limited by technical and quantum noise introduced by devices used for transduction and amplification of the inherently small signals of interest. Many experimental implementations, including nano-mechanical systems, solid-state quantum bits (qubits), and circuit quantum-electrodynamics (c-QED) devices, utilize transmitted or reflected microwave signals to measure the field quadratures of signals composed of few photons. Traditional low-noise cryogenic HEMT amplifiers provide an unsatisfactory solution to this quantum measurement problem because the targeted signal is often much smaller than the added noise. In principle, c-QED devices can be used for quantum-limited amplification, particularly as a parametric amplifier (PA). An ideal parametric amplifier should amplify signals without introducing additional noise, which would allow for the attainment of quantum feedback algorithms. In this thesis, I describe the characterization of a c-QED device, known as a tunable resonator, with the goal of quantifying its limits when used as a parametric amplifier. Tunable resonators are currently being used as PAs in quantum limited experiments, however, some of the underlying dynamics of these devices have not yet been fully characterized. I investigated the frequency, internal loss, power dependent frequency shift (nonlinearity) of a tunable microwave co-planar waveguide (CPW) resonator as a function of external magnetic flux biasing, which changes the effective length of the resonator. By looking at multiple samples with different design parameters, I observed that nonlinear damping is inherent to this device. Nonlinear damping had previously been observed but not described in sufficient detail to provide insight into its origins, which may explain some underlying dynamics of the tunable resonator. My measurements of the nonlinear damping shows that at larger flux biases, the nonlinear damping dominates linear internal losses and represent the main contribution to the total internal loss rate. I then operated this device as a parametric oscillator (PO) and found that the nonlinear damping and large Kerr (or quartic) nonlinearity likely cause an increase in the above-threshold switching rates between π-phase shifted steady states, which in turn may be associated with anomalous above-threshold squeezing in these devices. The results of my thesis show that nonlinear damping is present in these devices and affects performance in them dearly. This result is important for future work in PAs as improved understanding of the nonlinear damping will enable engineering of a device which can act as a PA with maximal gain and minimum noise.
We have developed and measured a high-gain quantum-limited microwave parametric amplifier based on a superconducting lumped LC resonator with the inductor L including an array of eight superconducting quantum interference devices (SQUIDs). This amplifier is parametrically pumped by modulating the flux threading the SQUIDs at twice the resonator frequency. Around 5 GHz, a maximum gain of 31 dB, a product amplitude gain $\ifmmode\times\else\texttimes\fi{}$ bandwidth above 60 MHz, and a 1 dB compression point of $\ensuremath{-}123$ dBm at 20 dB gain are obtained in the nondegenerate mode of operation. Phase-sensitive amplification-deamplification is also measured in the degenerate mode and yields a maximum gain of 37 dB. The compression point obtained is 18 dB above what would be obtained with a single SQUID of the same inductance, due to the smaller nonlinearity of the SQUID array.
We characterize a Josephson parametric amplifier based on a flux-tunable quarter-wavelength resonator. The fundamental resonance frequency is ∼1 GHz, but we use higher modes of the resonator for our measurements. An on-chip tuning line allows for magnetic flux pumping of the amplifier. We investigate and compare degenerate parametric amplification, involving a single mode, and nondegenerate parametric amplification, using a pair of modes. We show that we reach quantum-limited noise performance in both cases.