Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2312.00528 · Physical Review Applied

Mo - Si superconducting nanowire single-photon detectors on Ga As

Marcel Erbe, Riad Berrazouane, Simon Geyer, Lorenzo Stasi, F. van der Brugge, Gaëtan Gras, Marcel Schmidt, Andreas Dirk Wieck, Arne Ludwig, Félix Bussières, Richard John Warburton

Published Jul 29, 2024• 5 citations
arXivHTMLPDF

Abstract

We report on $\mathrm{Mo}$-$\mathrm{Si}$-based superconducting nanowire single-photon detectors on a gallium arsenide substrate. $\mathrm{Mo}$-$\mathrm{Si}$ deposited on a passivated $\mathrm{Ga}\mathrm{As}$ surface has the same critical temperature as $\mathrm{Mo}$-$\mathrm{Si}$ deposited on silicon. The critical temperature decreases slightly on depositing $\mathrm{Mo}$-$\mathrm{Si}$ directly on the native oxide of $\mathrm{Ga}\mathrm{As}$. Hence, $\mathrm{Mo}$-$\mathrm{Si}$ works well as a thin-film superconductor on $\mathrm{Ga}\mathrm{As}$. We propose that the amorphous structure of $\mathrm{Mo}$-$\mathrm{Si}$ ensures compatibility with the $\mathrm{Ga}\mathrm{As}$ matrix. Superconducting nanowire single-photon detectors (SNSPDs) are fabricated with $\mathrm{Mo}$-$\mathrm{Si}$ on $\mathrm{Ga}\mathrm{As}$ using a meander-wire design. The SNSPD metrics are very similar to those of devices fabricated with the same procedure on a silicon substrate. We observe a plateau in the response-versus-bias curve, signaling a saturated internal quantum efficiency. The plateau remains even at an elevated temperature, 2.2 K, at a wavelength of 980 nm. We achieve a timing jitter of 50 ps and a recovery time of 29 ns. These results point to the promise of integrating $\mathrm{Mo}$-$\mathrm{Si}$ SNSPDs with $\mathrm{Ga}\mathrm{As}$ photonic circuits.

DOI
10.1103/physrevapplied.22.014072

Related papers

Fabrication of Superconducting Nanowire Single-Photon Detectors Using MoN

M. Nishikawa, K. Sawai, Kento Sakai +5 more

We report the fabrication of superconducting nanowire single-photon detector (SNSPD, SSPD) based on molybdenum nitride (MoN) film with and without a cavity structure. Ultrathin polycrystalline γ-Mo2N films with aTcabout 6 K were obtained by reactive DC magnetron sputtering. The absorption efficiency of the device was calculated by the finite-difference time-domain (FDTD) method using the optical constants of MoN determined by ellipsometry measurements. The SNSPD with a meander of 150-nm-width and 7-nm-thick nanowire showed a long saturation plateau in the bias current dependence of the system detection efficiency (SDE) at visible wavelength. The SNSPD with a cavity structure showed an SDE of 37% and a timing jitter of 79 ps at a wavelength of 1560 nm. The results show that MoN is a promising alternative to amorphous superconductors for high-performance SNSPD.

IEEE Transactions on Applied Superconductivity•Jan 25, 2022•3 citations

Superconducting single-photon detector made of MoSi film

Yu. P. Korneeva, M. Yu. Mikhaĭlov, Yuriy P. Pershyn +8 more

We fabricated and characterized nanowire superconducting single-photon detectors made of 4 nm thick amorphous Mo x Si 1− x films. At 1.7 K the best devices exhibit a detection efficiency (DE) up to 18% at 1.2 wavelength of unpolarized light, a characteristic response time of about 6 ns and timing jitter of 120 ps. The DE was studied in wavelength range from 650 nm to 2500 nm. At wavelengths below 1200 nm these detectors reach their maximum DE limited by photon absorption in the thin MoSi film.

arXiv:1309.7074•Superconductor Science and Technology•Aug 12, 2014•97 citations

Impact of Stoichiometry of MoSi Thin Films for Enhanced Sensitivity of Superconducting Nanowire Single-Photon Detectors

Stefanie Grotowski, Damjan Pecijareski, Hadrien Le Petit Delacour +8 more

We report on the impact of the stoichiometry of superconducting MoSi thin films on the performance of superconducting nanowire single-photon detectors (SNSPDs). Specifically, we investigate the relation between the film parameters critical temperature Tc , sheet resistance Rs and superconductor thickness d and observe a universal scaling behavior. To benchmark the performance of SNSPDs fabricated from films having different stoichiometry, we measure the bias dependent count rate curves, while the detector is illuminated with wavelengths between 780 nm and 1550 nm. The detector performance as a function photon energy for different nanowire widths reveals a linear relation between the detection current and the photon energy. Furthermore, we determine the interfacial thermal boundary conductance $β$ between the superconducting thin film and the substrate, by measuring the return current of the SNSPD and find an increase of $β$ with increasing Mo concentration. The highest sensitivity amongst all compared devices is achieved for Mo$_{0.53}$Si$_{0.47}$, with low Tc (4.1 K) and high Rs (397$Ω$/sq) at a film thickness of 5.4 nm.

cond-mat.supr-conCross-listedarXiv:2605.27179•Materials for Quantum Technology•May 27, 2026•0 citations

MoRe superconducting nanowire single-photon detector atop of lithium niobate on insulator

A. A. Nevzorov, И. О. Венедиктов, Vladislav Korovin +8 more

We demonstrate an amorphous molybdenum–rhenium (MoRe) film on a thin-film lithium niobate substrate as an efficient superconducting nanowire single-photon detector (SNSPD) operating at T = 2.5 K. MoRe films were deposited by DC magnetron sputtering with a composite target of 56 at. % Mo and 44 at. % Re on lithium niobate on insulator substrates at room temperature. We investigated the spectral and temporal performance of MoRe SNSPDs as well as the detection regimes of one and multiple photons. The fabricated detector with a nanowire width of about 150 nm shows an internal detection efficiency of approximately 98% and 73.5% for the most crucial wavelengths for integration on the chip, 780 and 1550 nm, respectively. Our results show great potential for the use of MoRe for scalable and cryogenic tunable quantum photonic integrated circuits.

Applied Physics Letters•Oct 23, 2025•3 citations

Superconducting nanowire single photon detectors fabricated from an amorphous Mo0.75Ge0.25 thin film

Varun Boehm Verma, Adriana E. Lita, Michael R. Vissers +4 more

We present the characteristics of superconducting nanowire single photon detectors (SNSPDs) fabricated from amorphous Mo0.75Ge0.25 thin-films. Fabricated devices show a saturation of the internal detection efficiency at temperatures below 1 K, with system dark count rates below 500 cps. Operation in a closed-cycle cryocooler at 2.5 K is possible with system detection efficiencies exceeding 20% for SNSPDs which have not been optimized for high detection efficiency. Jitter is observed to vary between 69 ps at 250 mK and 187 ps at 2.5 K using room temperature amplifiers.

arXiv:1402.4526•Applied Physics Letters•Jul 14, 2014•77 citations

Emerging materials for superconducting nanowire photon counting arrays

Umberto Nasti

Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.

•Jan 1, 2020•0 citations
We report on Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si-based superconducting nanowire single-photon detectors on a gallium arsenide substrate. Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si deposited on a passivated GaAs\mathrm{Ga}\mathrm{As}GaAs surface has the same critical temperature as Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si deposited on silicon. The critical temperature decreases slightly on depositing Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si directly on the native oxide of GaAs\mathrm{Ga}\mathrm{As}GaAs. Hence, Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si works well as a thin-film superconductor on GaAs\mathrm{Ga}\mathrm{As}GaAs. We propose that the amorphous structure of Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si ensures compatibility with the GaAs\mathrm{Ga}\mathrm{As}GaAs matrix. Superconducting nanowire single-photon detectors (SNSPDs) are fabricated with Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si on GaAs\mathrm{Ga}\mathrm{As}GaAs using a meander-wire design. The SNSPD metrics are very similar to those of devices fabricated with the same procedure on a silicon substrate. We observe a plateau in the response-versus-bias curve, signaling a saturated internal quantum efficiency. The plateau remains even at an elevated temperature, 2.2 K, at a wavelength of 980 nm. We achieve a timing jitter of 50 ps and a recovery time of 29 ns. These results point to the promise of integrating Mo\mathrm{Mo}Mo-Si\mathrm{Si}Si SNSPDs with GaAs\mathrm{Ga}\mathrm{As}GaAs photonic circuits.
We report the fabrication of superconducting nanowire single-photon detector (SNSPD, SSPD) based on molybdenum nitride (MoN) film with and without a cavity structure. Ultrathin polycrystalline γ-Mo2N films with aTcabout 6 K were obtained by reactive DC magnetron sputtering. The absorption efficiency of the device was calculated by the finite-difference time-domain (FDTD) method using the optical constants of MoN determined by ellipsometry measurements. The SNSPD with a meander of 150-nm-width and 7-nm-thick nanowire showed a long saturation plateau in the bias current dependence of the system detection efficiency (SDE) at visible wavelength. The SNSPD with a cavity structure showed an SDE of 37% and a timing jitter of 79 ps at a wavelength of 1560 nm. The results show that MoN is a promising alternative to amorphous superconductors for high-performance SNSPD.
We report on the impact of the stoichiometry of superconducting MoSi thin films on the performance of superconducting nanowire single-photon detectors (SNSPDs). Specifically, we investigate the relation between the film parameters critical temperature Tc , sheet resistance Rs and superconductor thickness d and observe a universal scaling behavior. To benchmark the performance of SNSPDs fabricated from films having different stoichiometry, we measure the bias dependent count rate curves, while the detector is illuminated with wavelengths between 780 nm and 1550 nm. The detector performance as a function photon energy for different nanowire widths reveals a linear relation between the detection current and the photon energy. Furthermore, we determine the interfacial thermal boundary conductance βββ between the superconducting thin film and the substrate, by measuring the return current of the SNSPD and find an increase of βββ with increasing Mo concentration. The highest sensitivity amongst all compared devices is achieved for Mo0.53_{0.53}0.53​Si0.47_{0.47}0.47​, with low Tc (4.1 K) and high Rs (397ΩΩΩ/sq) at a film thickness of 5.4 nm.
We demonstrate an amorphous molybdenum–rhenium (MoRe) film on a thin-film lithium niobate substrate as an efficient superconducting nanowire single-photon detector (SNSPD) operating at T = 2.5 K. MoRe films were deposited by DC magnetron sputtering with a composite target of 56 at. % Mo and 44 at. % Re on lithium niobate on insulator substrates at room temperature. We investigated the spectral and temporal performance of MoRe SNSPDs as well as the detection regimes of one and multiple photons. The fabricated detector with a nanowire width of about 150 nm shows an internal detection efficiency of approximately 98% and 73.5% for the most crucial wavelengths for integration on the chip, 780 and 1550 nm, respectively. Our results show great potential for the use of MoRe for scalable and cryogenic tunable quantum photonic integrated circuits.
We present the characteristics of superconducting nanowire single photon detectors (SNSPDs) fabricated from amorphous Mo0.75Ge0.25 thin-films. Fabricated devices show a saturation of the internal detection efficiency at temperatures below 1 K, with system dark count rates below 500 cps. Operation in a closed-cycle cryocooler at 2.5 K is possible with system detection efficiencies exceeding 20% for SNSPDs which have not been optimized for high detection efficiency. Jitter is observed to vary between 69 ps at 250 mK and 187 ps at 2.5 K using room temperature amplifiers.
Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.