We present studies of resonance-enhanced photoionization for isotope-selective loading of
Ca+ into a Paul trap. The ${4s}^{2}{}^{1}{S}_{0}\ensuremath{\leftrightarrow}4s4p{}^{1}{P}_{1}$ transition of neutral calcium is driven by a 423 nm laser and the atoms are photoionized by a second laser at 389 nm. Isotope selectivity is achieved by using crossed atomic and laser beams to reduce the Doppler width significantly below the isotope shifts in the 423 nm transition. The loading rate of ions into the trap is studied under a range of experimental parameters for the abundant isotope
40Ca+. Using the fluorescence of the atomic beam at 423 nm as a measure of the Ca number density, we estimate a lower limit for the absolute photoionization cross section of 170(60) Mb. We achieve loading and laser cooling of all the naturally occurring isotopes, without the need for enriched sources. Laser heating/cooling is observed to enhance the isotope selectivity. In the case of the rare species
43Ca+ and
46Ca+, which have not previously been laser cooled, the loading is not fully isotope selective, but we show that pure crystals of
43Ca+ may nevertheless be obtained. We find that for loading
40Ca+ the 389 nm laser may be replaced by an incoherent source.
We report on the isotope-selective manipulation of Ca + using the laser-heating and laser-cooling techniques in a linear Paul trap. Only 40 Ca + was selectively laser-heated using the optical isotope shift and eliminated from the trap while keeping the target isotope in the trap. The elimination process of the dominant isotope 40 Ca + was investigated and 42, 43, 44, 48 Ca + in the natural isotope mixture of Ca + generated by laser ablation were successfully observed by means of applying the appropriate dc voltage on the end-cap electrodes without changing the laser frequencies, the laser powers and the duration of the laser irradiation. This simplified method enables us to efficiently laser-cool the rare isotopes.
We give a detailed characterization of a recently developed method to prepare translationally cold, internally state-selected molecular ions in ion traps [X. Tong, A. H. Winney, and S. Willitsch, Phys. Rev. Lett. 105, 143001 (2010)]. The technique relies on the generation of molecular ions in a well-defined rotational-vibrational quantum state using threshold photoionization followed by sympathetic cooling of the translational motion with laser-cooled Ca
+ ions. We discuss the experimental requirements for the successful generation and sympathetic cooling of state-selected ions, explore the influence of collisional and radiative processes on the population redistribution dynamics, and give an assessment of the scopeof the method.
The
133Ba+ ion is a promising candidate as a high-fidelity qubit, and the
137Ba+ isotope is promising as a high-fidelity qudit
(d>2). Barium metal is very reactive, and
133Ba+ is radioactive and can only be sourced in small quantities, so the most commonly used loading method, oven heating, is less suited for barium and is currently not possible for
133Ba+. Pulsed laser ablation solves both of these problems by utilizing compound barium sources while also giving some distinct advantages, such as fast loading, less displaced material, and lower heat load near the ion trap. Because of the relatively low abundances of the isotopes of interest, a two-step photoionization technique is used, which gives us the ability to selectively load isotopes. Characterization of the ablation process for our
BaCl2 targets are presented, including observation of neutral and ion ablation-fluence regimes, preparation and conditioning, lifetimes of ablation spots, and plume velocity distributions. We show that by using laser ablation on
BaCl2 salt targets with a two-step photoionization method, we can produce and trap barium ions reliably. Furthermore, we demonstrate that with our photoionization method, we can trap
137Ba+ with an enhanced selectivity compared to its natural abundance.
Cooling and trapping ion system is considered as a promising candidate for quantum information processor. Especially, by manipulating 133Ba+ ion, improved fidelity of qubit operation is expected, where selective 133Ba isotope introduction to the ion trap is required. Development of isotope selective loading system of Ba ion for the ion trap using the two-step laser photoionization is shown. For the excitation step (791 nm), the target isotope atom is photo-excited among other Ba isotopes based on their isotope shift. A tunable laser with a narrow spectral linewidth compared to the Ba isotope shift, was developed using an external cavity diode laser (ECDL). Mode-hop-free (MHF) scanning was achieved. For the second ionization step, a pulsed N2 laser was used. Both laser beams were combined using a mirror, focused with a lens, and introduced into a vacuum chamber. An atomic source was made by resistive heating, which can heat the source and generate atomic beam with sufficient vapor pressure and atomic density for the measurements. The system is under development and is prepared for the Ba atomic beam generation and laser photoionization experiments.
Abstract Trapped ions have emerged as a front runner in quantum information processing due to their identical nature, all-to-all connectivity, and high fidelity quantum operations. As current trapped ion technologies are scaled, it will be important to improve the efficiency of loading ions, especially when working with long chains of ions or rare isotopes. Here, we compare two different isotope-selective photoionization schemes for loading 138 Ba + ions. We show that a two-step photoionization scheme ending in an autoionizing transition increases the ion loading rate nearly an order of magnitude compared to an established technique which does not excite an autoionizing state. Our novel photoionization scheme can be extended to all isotopes of barium. Given that autoionizing resonances exist in every trapped ion species, exploitation of this process is a promising pathway to increase the loading rates for trapped ion computers.