Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2306.10162 · Nature Communications

Fast superconducting qubit control with subharmonic drives

Mingkang Xia, Chao Zhou, Chenxu Liu, Param Patel, Xi Cao, Pinlei Lu, Boris Mesits, Maria Mucci, David Gorski, David Pekker, Michael J. Hatridge

Published Dec 23, 2025• 23 citations
arXivHTMLPDF

Abstract

Increasing the fidelity of single-qubit gates requires a combination of faster pulses and increased qubit coherence. However, these requirements can be contradictory. Additionally, increasing the drive power can heat the qubit’s environment and degrade coherence. In this work, we circumvent this issue and achieve rapid gates by pumping a transmon’s native Kerr at approximately one third of the qubit’s resonant frequency. The subharmonic Rabi rate of the process is proportional to applied drive amplitude cubed, allowing for rapid gates. In addition, we demonstrate that filtering can be used to protect the qubit’s coherence while performing rapid gates. Single qubit gates as short as 37.4 ns are demonstrated with fidelity of 99.91%. We present theoretical calculations indicating that drive induced multi-photon decay will not limit qubit lifetime; calculated power absorption also indicates that this technique could reduce cryostat heating for fast gates, a vital requirement for large-scale quantum computers. There is a trade-off between achieving fast qubit control and preserving long qubit lifetimes. In this work, the authors demonstrate single qubit gates by driving a transmon qubit parametrically at 1/3 of its frequency, creating fast, high-fidelity gates while protecting the qubit lifetime and mitigating heating.

DOI
10.1038/s41467-025-67766-6

Related papers

Decay-protected superconducting qubit with fast control enabled by integrated on-chip filters

Aashish Sah, Suman Kundu, Heikki Suominen +2 more

Abstract Achieving fast gates and long coherence times for superconducting qubits presents challenges, typically requiring either a stronger coupling of the drive line or an excessively strong microwave signal to the qubit. To address this, we introduce on-chip filters of the qubit drive exhibiting a stopband at the qubit frequency, thus enabling long coherence times and strong coupling at the subharmonic frequency, facilitating fast single-qubit gates, and reduced thermal load. The filters exhibit an extrinsic relaxation time of a few seconds while enabling sub-10-ns gates with subharmonic control. Here we show up to 200-fold improvement in the measured relaxation time at the stopband. Furthermore, we implement subharmonic driving of Rabi oscillations with a π pulse duration of 12 ns. Our demonstration of on-chip filters and efficient subharmonic driving in a two-dimensional quantum processor paves the way for a scalable qubit architecture with reduced thermal load and noise from the control line.

arXiv:2402.08906•Communications Physics•Jul 12, 2024•14 citations

Subharmonic Control of a Fluxonium Qubit via a Purcell-Protected Flux Line

J. Schirk, Florian Wallner, L. Huang +21 more

Protecting qubits from environmental noise while maintaining strong coupling for fast high-fidelity control is a central challenge for quantum information processing. Here, we demonstrate a control scheme for superconducting fluxonium qubits that eliminates qubit decay through the control channel by suppressing the environmental density of states at the transition frequency. Adding a low-pass filter on the flux line allows for flux-biasing and, at the same time, coherently controlling the fluxonium qubit by parametrically driving it at integer fractions of its transition frequency. We compare the filtered to the unfiltered configuration and find a 5-times-longer T 1 , and a 10-times-improved T 2 -echo time in the filtered case. We demonstrate coherent control with up to 11-photon subharmonic drives, highlighting the strong nonlinearity of the fluxonium potential. Measured Rabi frequencies and drive-induced frequency shifts show excellent agreement with numerical and analytical models. Furthermore, we show the equivalence of a 3-photon subharmonic drive to an on-resonance drive by benchmarking subharmonic gate fidelities above 99.94%. These results open up a scalable path for full qubit control through a single Purcell-protected channel, providing strong suppression of control-induced decoherence and enabling wiring-efficient superconducting quantum processors.

arXiv:2410.00495•PRX Quantum•Jun 24, 2025•14 citations

Programmable coupling to electromagnetic environments in superconducting qubits

Aashish Sah

Superconducting quantum circuits have emerged as a leading platform for building large-scale quantum computers, owing to their ability to engineer strong, highly tunable interactions. However, achieving high-fidelity quantum operations requires overcoming the fundamental isolation-andcontrol challenge: qubits must be well-isolated from their electromagnetic environment to maintain long coherence times, yet they require strong external coupling for fast control, readout, and initialization. In current architectures, this trade-off often demands complex auxiliary circuitry that can introduce additional noise and thermal loads. This thesis presents novel circuit designs and control techniques to address the isolation-and-control challenge in superconducting transmon qubits. First, we introduce integrated on-chip filters, in particular, 𝜆/4 and 𝜆/2 transmission line filters that exhibit a stopband at the qubit frequency. This design protects the qubit from Purcell decay, yielding up to a 200-fold improvement in the energy relaxation time 𝑇1 at the stopband. To achieve fast single-qubit gates despite this isolation, we employ subharmonic driving, demonstrating sub-ten-nanosecond control and Rabi oscillations with a 12-ns pulse duration while significantly reducing the cryogenic thermal load. Building upon these static filters, we propose and experimentally demonstrate the quantum dial, a dynamically tunable band-stop filter consisting of a series array of direct-current superconducting quantum interference devices. The quantum dial enables on-demand tuning of the qubit–environment coupling, including a reduction of 𝑇1 from over 150 μs to roughly 200 ns, while introducing minimal ac Stark shifts. We demonstrate its versatility by dialing between three operational regimes: an idle state with 99.99% fidelity, a control state enabling 99.9% fidelity for 40-ns single-qubit gates at −110 dBm, and a strongly coupled state for unconditional, state-independent qubit reset. Furthermore, the quantum dial enables qubit thermometry close to the quantum-Fisherinformation bound, with a noise-equivalent temperature down to 0.6 mK/√Hz at 60 mK. Alongside the development of these dedicated control architectures, this thesis contributes to the broader framework of circuit quantum electrodynamics by advancing specific microwave engineering and characterization techniques. In particular, we explore the miniaturization of circuit footprints through the realization of compact sub-gigahertz inductor-capacitor resonators. Additionally, we contribute to the optimization of unconditional qubit reset using a single-junction quantum-circuit refrigerator, and to the advanced characterization of microwave fields via computed tomography of propagating microwave photons. In summary, these results demonstrate fixed and tunable drive-line filters that suppress idle-state radiative decay while preserving selected control, reset, and thermometry operations. By replacing static coupling compromises with temporally programmable environments, these architectures offer a promising route to reducing noise, mitigating crosstalk, and accelerating error-correction cycles in future superconducting quantum processors.

•Jan 1, 2026•0 citations

Decoherence in two-frequency-driven qubits

Väisänen, Petrus

Quantum computing has recently been a topic of great interest because quantum computers can possibly be used to solve problems that classical computers are unable to. However, the greatest holdback at the moment is that the fidelity of quantum gate operations is not high enough, which leads to inaccurate computations. A key aspect of quantum computing is single-qubit gates, which are executed utilizing external microwave photon sources, called qubit drives. Here, we theoretically investigate a quantum gate operation where a transmon qubit is controlled by two different driving frequencies at the same time. The two-frequency drive is a three-photon process, where the qubit gets excited when it absorbs two photons of one frequency and emits one photon of the other frequency. This allows placing on-chip filters on the drive ports that filter out noise at the qubit's transition frequency. We calculate the fidelity of the gate operation in the two-frequency-driven transmon starting with the Hamiltonian of the system. We assume the drive lines to be noisy, utilizing a classical model of noise, which inflicts small perturbations to the Hamiltonian. Hence, we utilize time-dependent perturbation theory in the calculations. The scaling of infidelity is found to be the same as in the case with resonant and subharmonic drives, being inversely proportional to the average photon numbers of the drives, assuming that the photon numbers are equal. The scaling of Rabi frequency is observed to be the same as with the subharmonic drive and better than with the resonant drive. Therefore, we obtain results for the two-frequency drive that are as good as the results in the subharmonic drive. An interesting observation is that decoherence seems to be partially caused by multi-photon processes at different frequencies.

•Dec 2, 2025•0 citations

Dynamically protected erasure qubit via low-frequency charge driving

Ahmed Hajr, Ke Wang, Bingcheng Qing +6 more

Dynamical protection via strong driving can enable resilient quantum processing on imperfect physical hardware. However, the practical utility of such schemes is frequently limited by parasitic processes such as drive-induced dephasing and leakage. Here, we demonstrate that sub-GHz charge driving of superconducting Kerr oscillators (KOs) in the transmon regime circumvents this trade-off, simultaneously activating fast parametric interactions and protecting the encoded qubit from low-frequency noise. The key is the frequency dependence of the charge sensitivity: using the AC Stark shift as a probe, we find that the KO frequency sensitivity to a charge drive grows quadratically with both drive frequency and amplitude, making the oscillator weakly sensitive to $1/f$ charge noise yet strongly coupled to drives near 1~GHz. Exploiting this, we first demonstrate cooling and reset of the KO in 82~ns, to a residual population below $0.7\%$---lower than its $2.5\%$ steady-state thermal population. Next, using two KOs, we demonstrate logical control and dynamical protection of a dual-rail qubit with nearly fourfold erasure bias. Finally, using a single end-of-circuit erasure check, we achieve an error per Clifford of $5.6\times10^{-4}$, which falls to $1.5\times10^{-4}$ after post-selection, with 25~ns gates.

quant-pharXiv:2610.10432•Oct 8, 2026•0 citations

Unified scaling of transmon sub-resonant parametric drive strength limits

Jacob Repicky, Girish Kumbhar, Mingkang Xia +6 more

Achieving fast gates and high-fidelity readout in superconducting quantum circuits often benefits from the use of large amplitude microwave drives. As the strength increases, unwanted effects such as excitation out of the logical states also become more prevalent. In transmon qubits, coherent controls relying on sub-resonant drives are fundamentally limited by the eventual appearance of strong hybridization in the spectrum. Understanding how this threshold depends on intrinsic device parameters is vital for the design and operation of circuits utilizing the transmon as a source of nonlinearity. In this work, we present an experimental study of 14 transmons with a wide range of anharmonicities, and use comparison with Floquet branch analysis and semiclassical simulations to establish a straightforward relationship between the critical value of the effective drive amplitude $η_{\max}$ and the ratio $γ=ω_q/α$, where $ω_q$ is the transmon frequency and $-α$ is the anharmonicity. For the case where the transmon is used as a parametrically driven coupler, these results further allow us to estimate maximum parametric interaction rates, which informs the circuit design process for optimizing gate rates and fidelities.

quant-pharXiv:2609.13055•Sep 14, 2026•1 citation
Increasing the fidelity of single-qubit gates requires a combination of faster pulses and increased qubit coherence. However, these requirements can be contradictory. Additionally, increasing the drive power can heat the qubit’s environment and degrade coherence. In this work, we circumvent this issue and achieve rapid gates by pumping a transmon’s native Kerr at approximately one third of the qubit’s resonant frequency. The subharmonic Rabi rate of the process is proportional to applied drive amplitude cubed, allowing for rapid gates. In addition, we demonstrate that filtering can be used to protect the qubit’s coherence while performing rapid gates. Single qubit gates as short as 37.4 ns are demonstrated with fidelity of 99.91%. We present theoretical calculations indicating that drive induced multi-photon decay will not limit qubit lifetime; calculated power absorption also indicates that this technique could reduce cryostat heating for fast gates, a vital requirement for large-scale quantum computers. There is a trade-off between achieving fast qubit control and preserving long qubit lifetimes. In this work, the authors demonstrate single qubit gates by driving a transmon qubit parametrically at 1/3 of its frequency, creating fast, high-fidelity gates while protecting the qubit lifetime and mitigating heating.
Abstract Achieving fast gates and long coherence times for superconducting qubits presents challenges, typically requiring either a stronger coupling of the drive line or an excessively strong microwave signal to the qubit. To address this, we introduce on-chip filters of the qubit drive exhibiting a stopband at the qubit frequency, thus enabling long coherence times and strong coupling at the subharmonic frequency, facilitating fast single-qubit gates, and reduced thermal load. The filters exhibit an extrinsic relaxation time of a few seconds while enabling sub-10-ns gates with subharmonic control. Here we show up to 200-fold improvement in the measured relaxation time at the stopband. Furthermore, we implement subharmonic driving of Rabi oscillations with a π pulse duration of 12 ns. Our demonstration of on-chip filters and efficient subharmonic driving in a two-dimensional quantum processor paves the way for a scalable qubit architecture with reduced thermal load and noise from the control line.
Protecting qubits from environmental noise while maintaining strong coupling for fast high-fidelity control is a central challenge for quantum information processing. Here, we demonstrate a control scheme for superconducting fluxonium qubits that eliminates qubit decay through the control channel by suppressing the environmental density of states at the transition frequency. Adding a low-pass filter on the flux line allows for flux-biasing and, at the same time, coherently controlling the fluxonium qubit by parametrically driving it at integer fractions of its transition frequency. We compare the filtered to the unfiltered configuration and find a 5-times-longer T 1 , and a 10-times-improved T 2 -echo time in the filtered case. We demonstrate coherent control with up to 11-photon subharmonic drives, highlighting the strong nonlinearity of the fluxonium potential. Measured Rabi frequencies and drive-induced frequency shifts show excellent agreement with numerical and analytical models. Furthermore, we show the equivalence of a 3-photon subharmonic drive to an on-resonance drive by benchmarking subharmonic gate fidelities above 99.94%. These results open up a scalable path for full qubit control through a single Purcell-protected channel, providing strong suppression of control-induced decoherence and enabling wiring-efficient superconducting quantum processors.
Superconducting quantum circuits have emerged as a leading platform for building large-scale quantum computers, owing to their ability to engineer strong, highly tunable interactions. However, achieving high-fidelity quantum operations requires overcoming the fundamental isolation-andcontrol challenge: qubits must be well-isolated from their electromagnetic environment to maintain long coherence times, yet they require strong external coupling for fast control, readout, and initialization. In current architectures, this trade-off often demands complex auxiliary circuitry that can introduce additional noise and thermal loads. This thesis presents novel circuit designs and control techniques to address the isolation-and-control challenge in superconducting transmon qubits. First, we introduce integrated on-chip filters, in particular, 𝜆/4 and 𝜆/2 transmission line filters that exhibit a stopband at the qubit frequency. This design protects the qubit from Purcell decay, yielding up to a 200-fold improvement in the energy relaxation time 𝑇1 at the stopband. To achieve fast single-qubit gates despite this isolation, we employ subharmonic driving, demonstrating sub-ten-nanosecond control and Rabi oscillations with a 12-ns pulse duration while significantly reducing the cryogenic thermal load. Building upon these static filters, we propose and experimentally demonstrate the quantum dial, a dynamically tunable band-stop filter consisting of a series array of direct-current superconducting quantum interference devices. The quantum dial enables on-demand tuning of the qubit–environment coupling, including a reduction of 𝑇1 from over 150 μs to roughly 200 ns, while introducing minimal ac Stark shifts. We demonstrate its versatility by dialing between three operational regimes: an idle state with 99.99% fidelity, a control state enabling 99.9% fidelity for 40-ns single-qubit gates at −110 dBm, and a strongly coupled state for unconditional, state-independent qubit reset. Furthermore, the quantum dial enables qubit thermometry close to the quantum-Fisherinformation bound, with a noise-equivalent temperature down to 0.6 mK/√Hz at 60 mK. Alongside the development of these dedicated control architectures, this thesis contributes to the broader framework of circuit quantum electrodynamics by advancing specific microwave engineering and characterization techniques. In particular, we explore the miniaturization of circuit footprints through the realization of compact sub-gigahertz inductor-capacitor resonators. Additionally, we contribute to the optimization of unconditional qubit reset using a single-junction quantum-circuit refrigerator, and to the advanced characterization of microwave fields via computed tomography of propagating microwave photons. In summary, these results demonstrate fixed and tunable drive-line filters that suppress idle-state radiative decay while preserving selected control, reset, and thermometry operations. By replacing static coupling compromises with temporally programmable environments, these architectures offer a promising route to reducing noise, mitigating crosstalk, and accelerating error-correction cycles in future superconducting quantum processors.
Quantum computing has recently been a topic of great interest because quantum computers can possibly be used to solve problems that classical computers are unable to. However, the greatest holdback at the moment is that the fidelity of quantum gate operations is not high enough, which leads to inaccurate computations. A key aspect of quantum computing is single-qubit gates, which are executed utilizing external microwave photon sources, called qubit drives. Here, we theoretically investigate a quantum gate operation where a transmon qubit is controlled by two different driving frequencies at the same time. The two-frequency drive is a three-photon process, where the qubit gets excited when it absorbs two photons of one frequency and emits one photon of the other frequency. This allows placing on-chip filters on the drive ports that filter out noise at the qubit's transition frequency. We calculate the fidelity of the gate operation in the two-frequency-driven transmon starting with the Hamiltonian of the system. We assume the drive lines to be noisy, utilizing a classical model of noise, which inflicts small perturbations to the Hamiltonian. Hence, we utilize time-dependent perturbation theory in the calculations. The scaling of infidelity is found to be the same as in the case with resonant and subharmonic drives, being inversely proportional to the average photon numbers of the drives, assuming that the photon numbers are equal. The scaling of Rabi frequency is observed to be the same as with the subharmonic drive and better than with the resonant drive. Therefore, we obtain results for the two-frequency drive that are as good as the results in the subharmonic drive. An interesting observation is that decoherence seems to be partially caused by multi-photon processes at different frequencies.
Dynamical protection via strong driving can enable resilient quantum processing on imperfect physical hardware. However, the practical utility of such schemes is frequently limited by parasitic processes such as drive-induced dephasing and leakage. Here, we demonstrate that sub-GHz charge driving of superconducting Kerr oscillators (KOs) in the transmon regime circumvents this trade-off, simultaneously activating fast parametric interactions and protecting the encoded qubit from low-frequency noise. The key is the frequency dependence of the charge sensitivity: using the AC Stark shift as a probe, we find that the KO frequency sensitivity to a charge drive grows quadratically with both drive frequency and amplitude, making the oscillator weakly sensitive to 1/f1/f1/f charge noise yet strongly coupled to drives near 1~GHz. Exploiting this, we first demonstrate cooling and reset of the KO in 82~ns, to a residual population below 0.7%0.7\%0.7%---lower than its 2.5%2.5\%2.5% steady-state thermal population. Next, using two KOs, we demonstrate logical control and dynamical protection of a dual-rail qubit with nearly fourfold erasure bias. Finally, using a single end-of-circuit erasure check, we achieve an error per Clifford of 5.6×10−45.6\times10^{-4}5.6×10−4, which falls to 1.5×10−41.5\times10^{-4}1.5×10−4 after post-selection, with 25~ns gates.
Achieving fast gates and high-fidelity readout in superconducting quantum circuits often benefits from the use of large amplitude microwave drives. As the strength increases, unwanted effects such as excitation out of the logical states also become more prevalent. In transmon qubits, coherent controls relying on sub-resonant drives are fundamentally limited by the eventual appearance of strong hybridization in the spectrum. Understanding how this threshold depends on intrinsic device parameters is vital for the design and operation of circuits utilizing the transmon as a source of nonlinearity. In this work, we present an experimental study of 14 transmons with a wide range of anharmonicities, and use comparison with Floquet branch analysis and semiclassical simulations to establish a straightforward relationship between the critical value of the effective drive amplitude ηmax⁡η_{\max}ηmax​ and the ratio γ=ωq/αγ=ω_q/αγ=ωq​/α, where ωqω_qωq​ is the transmon frequency and −α-α−α is the anharmonicity. For the case where the transmon is used as a parametrically driven coupler, these results further allow us to estimate maximum parametric interaction rates, which informs the circuit design process for optimizing gate rates and fidelities.