Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2306.00782 · Journal of Physics B Atomic Molecular and Optical Physics

Design and simulation of a source of cold cadmium for atom interferometry

Satvika Bandarupally, Jonathan N. Tinsley, Mauro Chiarotti, N. Poli

Published Aug 24, 2023• 6 citations
arXivHTMLPDF

Abstract

Abstract We present a novel optimised design for a source of cold atomic cadmium, compatible with continuous operation and potentially quantum degenerate gas production. The design is based on spatially segmenting the first and second-stages of cooling with the strong dipole-allowed 1S0-1P1 transition at 229 nm and the 326 nm 1S0-3P1 intercombination transition, respectively. Cooling at 229 nm operates on an effusive atomic beam and takes the form of a compact Zeeman slower (∼5 cm) and two-dimensional magneto-optical trap (MOT), both based on permanent magnets. This design allows for reduced interaction time with the photoionising 229 nm photons and produces a slow beam of atoms that can be directly loaded into a three-dimensional MOT using the intercombination transition. The efficiency of the above process is estimated across a broad range of experimentally feasible parameters via use of a Monte Carlo simulation, with loading rates up to 108 atoms s−1 into the 326 nm MOT possible with the oven at only 100 ∘C. The prospects for further cooling in a far-off-resonance optical-dipole trap and atomic launching in a moving optical lattice are also analysed, especially with reference to the deployment in a proposed dual-species cadmium-strontium atom interferometer.

DOI
10.1088/1361-6455/acf3bf

Related papers

A new design of a compact strontium cold-atom source

Dongyang Xu

A high-flux compact source of strontium atoms has been designed and built. We have investigated the feasibility of direct trapping of cold atoms from the atomic flux out of a hot oven. Our design uses a two-dimensional magneto-optical trap (MOT) with an additional laser beam that exerts a radiation force that is not counterbalanced to eject atoms (so-called ‘push’ beam), which is known as a 2D+ MOT configuration. This approach has been previously used for sodium, and has been extended to strontium in this work. Laser cooling of strontium typically requires multiple stages: effusion of atoms from an oven to produce an atomic beam, transverse collimation, a Zeeman slower and deflection before finally collecting atoms in a 3D MOT. A 2D+ MOT combines the Zeeman slowing, transverse collimation, and deflection into a single compact stage to provide a high-flux source suitable for applications such as matter-wave interferometry, atomic clocks and experimental studies of degenerate quantum gases. This thesis reports experimental work that has been carried out to develop and test an oven and the associated laser cooling apparatus for producing a source of cold strontium atoms which is straightforward to manufacture. We test the oven up to a temperature of To = 642 °C and measure a peak intensity of 6.8 × 1016 s−1 sr−1 and a flux of 2.9 × 1016 s−1. We typically operate the oven at To = 502 °C, for which the peak intensity and flux are 2.2 × 1015 s−1 sr−1 and 7.5 × 1014 s−1. A multi-channel nozzle made of graphite gives an angular divergence of 0.17 rad (10°) for the atomic beam. Trapping atoms directly from the thermal atomic beam into the MOT gives a maximum loading rate of 7.1 × 1010 s−1, without any laser light to repump atoms into the cooling cycle. We demonstrated a novel frequency stabilising technique for the laser by developing Zeeman-tunable modulation transfer spectroscopy in strontium with an inaccuracy of ±3.5 MHz and a frequency tuning range of 160 MHz. The initial aim of this thesis was to make a compact, high-flux strontium source suitable for quantum technology applications. During the course of this research, we participated in the preparation of a proposal for the construction of a large-scale atom interferometer based on the clock transition in strontium (87Sr) for the exploration of dark matter and gravitational waves (a project known as the Atom Interferometer Observatory and Network, AION). This changed the design requirements towards producing a higher flux (in particular of the isotope 87Sr), with compactness of the source being less important in ∼10 m scale apparatus.

•Jan 1, 2020•0 citations

Dual atomic interferometry for differential inertial sensing

Jianing Li

The utilization of light-pulse atom interferometry presents a valuable technique that has found application in both fundamental scientific inquiries, such as investigating constants such as measurements of fine structure constant α and gravitational constant G, and practical endeavors including acceleration sensing and rotation measurements. This thesis delves into our implementation of a dual atom interferometer design involving the clock transition 1S0 → 3P0 in strontium, concurrently conducting the interferometric sequence on atoms in both ground and excited states. To facilitate the dual atom interferometer’s operation, we have firstly established a compact experimental setup with a transversely loaded bi-dimensional magneto-optical-trap (2D-MOT) to create a high flux source of cold strontium atoms. Introducing a novel cross-polarized bi-color atomic beam slower, we simultaneously addresses two excited Zeeman substates of the transition 1S0 → 1P1 in strontium-88, significantly enhancing the number of atoms prepared in the 461 nm MOT by around 10-fold. Following the 461 nm MOT, the atomic ensemble undergoes cooling in a 689 nm MOT, achieving atomic temperatures below 1 µK. We also install a network of eight magnetic field probes arranged around the cold atomic sample, enabling precise three-axis active control of magnetic fields down to the milligauss level. With the atoms confined in a 2D lattice at the magic-wavelength of 813.427 nm after the initial preparation phase, we conduct the magnetically-induced clock transition to create a statistical mixture state of ground and excited states. After a velocity selection stage, implementing a Mach-Zehnder interferometer with Bragg pulses operating at the magic-wavelength along the vertical axis, we conduct tests of the weak equivalence principle (WEP). The Eötvös ratio we found in our system stood at (1.8 ± 3.1) × 10−4, mainly limited by the finite temperature of the atomic cloud constraining the interrogation time. Furthermore, the dual atom interferometer scheme enables the measurement of state-dependent force and eventually polarizability difference via the phase shift between the atoms in different states, and we experimentally demonstrate this by introducing an additional light field gradient.

•Jan 1, 2023•0 citations

An adaptable dual species effusive source and Zeeman slower design demonstrated with Rb and Li

William Bowden, Will Gunton, Mariusz Semczuk +2 more

We present a dual-species effusive source and Zeeman slower designed to produce slow atomic beams of two elements with a large mass difference and with very different oven temperature requirements. We demonstrate this design for the case of (6)Li and (85)Rb and achieve magneto-optical trap (MOT) loading rates equivalent to that reported in prior work on dual species (Rb+Li) Zeeman slowers operating at the same oven temperatures. Key design choices, including thermally separating the effusive sources and using a segmented coil design to enable computer control of the magnetic field profile, ensure that the apparatus can be easily modified to slow other atomic species. By performing the final slowing using the quadrupole magnetic field of the MOT, we are able to shorten our Zeeman slower length making for a more compact system without compromising performance. We outline the construction and analyze the emission properties of our effusive sources. We also verify the performance of the source and slower, and we observe sequential loading rates of 12 × 10(8) atoms/s for a Rb oven temperature of 140 °C and 1.1 × 10(8) atoms/s for a Li reservoir at 460 °C, corresponding to reservoir lifetimes for continuous operation of 10 and 4 years, respectively.

arXiv:1509.07460•Review of Scientific Instruments•Apr 1, 2016•15 citations

Two-dimensional magneto-optical trap of dysprosium atoms as a compact source for efficient loading of a narrow-line three-dimensional magneto-optical trap

Shu‐Wei Jin, Jianshun Gao, Karthik Chandrashekara +3 more

We report on a scheme for loading dysprosium atoms into a narrow-line three-dimensional magneto-optical trap (3D MOT). Our approach replaces the conventional Zeeman slower with a two-dimensional (2D) MOT operating on the broad 421-nm line to create a high-flux beam of slow atoms. Even in the absence of a push beam, we demonstrate efficient loading of the 3D MOT, which operates on the narrower 626-nm intercombination line. Adding push beams working at either 421 nm or 626 nm, significant enhancement of the loading rate is achieved. We reach the best performance, with an enhancement factor of 3.6, using a push beam red-detuned to the 626-nm line. With loading rates greater than ${10}^{8}\phantom{\rule{0.16em}{0ex}}\text{atoms/s}$ achieved at a moderate oven reservoir temperature of ${800}^{\ensuremath{\circ}}\phantom{\rule{0.16em}{0ex}}\mathrm{C}$, our method offers similar or greater performance than Zeeman-slower-based systems. Our 2D-MOT-based approach constitutes a promising first step towards state-of-the-art quantum gas experiments with several advantages over the Zeeman-slower-based setup and is readily adaptable to other open-shell lanthanides.

arXiv:2303.05191•Physical Review A•Aug 18, 2023•18 citations

A Compact Dual-Beam Zeeman Slower for High-Flux Cold Atoms

Chen Chen, Kejun Liu, Dezhou Deng +6 more

We present a compact design of dual-beam Zeeman slower optimized for efficient production of cold atom applications. Traditional single-beam configurations face challenges from substantial residual atomic flux impacting downstream optical windows, resulting in increased system size, atomic deposition contamination, and a reduced operational lifetime. Our approach employs two oblique laser beams and a capillary-array collimation system to address these challenges while maintaining efficient deceleration. For rubidium ($^{87}$Rb), simulations demonstrate a significant increase in the fraction of atoms captured by a two-dimensional magneto-optical trap (2D-MOT) and nearly eliminate atom-induced contamination probability at optical windows, all within a compact Zeeman slower length of 44 cm. Experimental validation with Rb and Yb demonstrates highly efficient atomic loading within the same compact design. This advancement represents a substantial improvement for high-flux cold atom applications, providing reliable performance for high-precision metrology, quantum computation and simulation.

physics.atom-phCross-listedarXiv:2511.08193•Physical Review Applied•Nov 12, 2025•2 citations

A dual species MOT of Yb and Cs

Kirsteen Louisa Butler

This thesis describes the design and construction of a new apparatus to laser cool and trap Yb and Cs atoms with the ultimate aim of creating ultracold molecules with both an electric and magnetic dipole moment, which are of great interest in a range of fields. The Yb and Cs atomic beams are first generated and overlapped in a dual species oven. A collimated atomic beam of the two species is formed by the use of an array of capillary tubes at the exit of the oven. At this stage the atoms have an average velocity of 311m/s or 264m/s for Yb and Cs respectively, therefore it is necessary to reduce their velocity before they can be trapped in a magneto-optical trap (MOT). This initial stage of slowing is carried out with a Zeeman slower. Due to their atomic properties, Yb and Cs atoms are unable to be slowed by the same magnetic field profile therefore they cannot be loaded simultaneously, however, the Zeeman slower can load the atoms into a MOT sequentially. Once their velocities have been reduced to approximately 48m/s (10m/s) the Cs (Yb) atoms can be captured in a MOT. The laser systems for cooling Yb and Cs are also presented. Laser cooling of Cs is achieved on the D2 transition at 852.3nm whereas Yb can either be cooled on the 1S0 to 1P1 or 1S0 to 3P1 transitions at 398.9nm or 555.8nm respectively. Due to the relative linewidths of these transitions (2π×28.0MHz and 2π × 182.2kHz), Zeeman slowing is performed for Yb on the 1S0 to 1P1 transition and magneto-optical trapping on the 1S0 to 3P1 transition. A Cs MOT with 1 × 10^8 atoms and an Yb MOT with the order of 10^8 atoms on the narrow 556nm transition are demonstrated. The mixture can be sequentially loaded into a dual species MOT, paving the way for many further experiments exploring this novel mixture.

•Jan 1, 2014•1 citation
Abstract We present a novel optimised design for a source of cold atomic cadmium, compatible with continuous operation and potentially quantum degenerate gas production. The design is based on spatially segmenting the first and second-stages of cooling with the strong dipole-allowed 1S0-1P1 transition at 229 nm and the 326 nm 1S0-3P1 intercombination transition, respectively. Cooling at 229 nm operates on an effusive atomic beam and takes the form of a compact Zeeman slower (∼5 cm) and two-dimensional magneto-optical trap (MOT), both based on permanent magnets. This design allows for reduced interaction time with the photoionising 229 nm photons and produces a slow beam of atoms that can be directly loaded into a three-dimensional MOT using the intercombination transition. The efficiency of the above process is estimated across a broad range of experimentally feasible parameters via use of a Monte Carlo simulation, with loading rates up to 108 atoms s−1 into the 326 nm MOT possible with the oven at only 100 ∘C. The prospects for further cooling in a far-off-resonance optical-dipole trap and atomic launching in a moving optical lattice are also analysed, especially with reference to the deployment in a proposed dual-species cadmium-strontium atom interferometer.
A high-flux compact source of strontium atoms has been designed and built. We have investigated the feasibility of direct trapping of cold atoms from the atomic flux out of a hot oven. Our design uses a two-dimensional magneto-optical trap (MOT) with an additional laser beam that exerts a radiation force that is not counterbalanced to eject atoms (so-called ‘push’ beam), which is known as a 2D+ MOT configuration. This approach has been previously used for sodium, and has been extended to strontium in this work. Laser cooling of strontium typically requires multiple stages: effusion of atoms from an oven to produce an atomic beam, transverse collimation, a Zeeman slower and deflection before finally collecting atoms in a 3D MOT. A 2D+ MOT combines the Zeeman slowing, transverse collimation, and deflection into a single compact stage to provide a high-flux source suitable for applications such as matter-wave interferometry, atomic clocks and experimental studies of degenerate quantum gases. This thesis reports experimental work that has been carried out to develop and test an oven and the associated laser cooling apparatus for producing a source of cold strontium atoms which is straightforward to manufacture. We test the oven up to a temperature of To = 642 °C and measure a peak intensity of 6.8 × 1016 s−1 sr−1 and a flux of 2.9 × 1016 s−1. We typically operate the oven at To = 502 °C, for which the peak intensity and flux are 2.2 × 1015 s−1 sr−1 and 7.5 × 1014 s−1. A multi-channel nozzle made of graphite gives an angular divergence of 0.17 rad (10°) for the atomic beam. Trapping atoms directly from the thermal atomic beam into the MOT gives a maximum loading rate of 7.1 × 1010 s−1, without any laser light to repump atoms into the cooling cycle. We demonstrated a novel frequency stabilising technique for the laser by developing Zeeman-tunable modulation transfer spectroscopy in strontium with an inaccuracy of ±3.5 MHz and a frequency tuning range of 160 MHz. The initial aim of this thesis was to make a compact, high-flux strontium source suitable for quantum technology applications. During the course of this research, we participated in the preparation of a proposal for the construction of a large-scale atom interferometer based on the clock transition in strontium (87Sr) for the exploration of dark matter and gravitational waves (a project known as the Atom Interferometer Observatory and Network, AION). This changed the design requirements towards producing a higher flux (in particular of the isotope 87Sr), with compactness of the source being less important in ∼10 m scale apparatus.
The utilization of light-pulse atom interferometry presents a valuable technique that has found application in both fundamental scientific inquiries, such as investigating constants such as measurements of fine structure constant α and gravitational constant G, and practical endeavors including acceleration sensing and rotation measurements. This thesis delves into our implementation of a dual atom interferometer design involving the clock transition 1S0 → 3P0 in strontium, concurrently conducting the interferometric sequence on atoms in both ground and excited states. To facilitate the dual atom interferometer’s operation, we have firstly established a compact experimental setup with a transversely loaded bi-dimensional magneto-optical-trap (2D-MOT) to create a high flux source of cold strontium atoms. Introducing a novel cross-polarized bi-color atomic beam slower, we simultaneously addresses two excited Zeeman substates of the transition 1S0 → 1P1 in strontium-88, significantly enhancing the number of atoms prepared in the 461 nm MOT by around 10-fold. Following the 461 nm MOT, the atomic ensemble undergoes cooling in a 689 nm MOT, achieving atomic temperatures below 1 µK. We also install a network of eight magnetic field probes arranged around the cold atomic sample, enabling precise three-axis active control of magnetic fields down to the milligauss level. With the atoms confined in a 2D lattice at the magic-wavelength of 813.427 nm after the initial preparation phase, we conduct the magnetically-induced clock transition to create a statistical mixture state of ground and excited states. After a velocity selection stage, implementing a Mach-Zehnder interferometer with Bragg pulses operating at the magic-wavelength along the vertical axis, we conduct tests of the weak equivalence principle (WEP). The Eötvös ratio we found in our system stood at (1.8 ± 3.1) × 10−4, mainly limited by the finite temperature of the atomic cloud constraining the interrogation time. Furthermore, the dual atom interferometer scheme enables the measurement of state-dependent force and eventually polarizability difference via the phase shift between the atoms in different states, and we experimentally demonstrate this by introducing an additional light field gradient.
We present a dual-species effusive source and Zeeman slower designed to produce slow atomic beams of two elements with a large mass difference and with very different oven temperature requirements. We demonstrate this design for the case of (6)Li and (85)Rb and achieve magneto-optical trap (MOT) loading rates equivalent to that reported in prior work on dual species (Rb+Li) Zeeman slowers operating at the same oven temperatures. Key design choices, including thermally separating the effusive sources and using a segmented coil design to enable computer control of the magnetic field profile, ensure that the apparatus can be easily modified to slow other atomic species. By performing the final slowing using the quadrupole magnetic field of the MOT, we are able to shorten our Zeeman slower length making for a more compact system without compromising performance. We outline the construction and analyze the emission properties of our effusive sources. We also verify the performance of the source and slower, and we observe sequential loading rates of 12 × 10(8) atoms/s for a Rb oven temperature of 140 °C and 1.1 × 10(8) atoms/s for a Li reservoir at 460 °C, corresponding to reservoir lifetimes for continuous operation of 10 and 4 years, respectively.
We report on a scheme for loading dysprosium atoms into a narrow-line three-dimensional magneto-optical trap (3D MOT). Our approach replaces the conventional Zeeman slower with a two-dimensional (2D) MOT operating on the broad 421-nm line to create a high-flux beam of slow atoms. Even in the absence of a push beam, we demonstrate efficient loading of the 3D MOT, which operates on the narrower 626-nm intercombination line. Adding push beams working at either 421 nm or 626 nm, significant enhancement of the loading rate is achieved. We reach the best performance, with an enhancement factor of 3.6, using a push beam red-detuned to the 626-nm line. With loading rates greater than 108atoms/s{10}^{8}\phantom{\rule{0.16em}{0ex}}\text{atoms/s}108atoms/s achieved at a moderate oven reservoir temperature of ${800}^{\ensuremath{\circ}}\phantom{\rule{0.16em}{0ex}}\mathrm{C}$, our method offers similar or greater performance than Zeeman-slower-based systems. Our 2D-MOT-based approach constitutes a promising first step towards state-of-the-art quantum gas experiments with several advantages over the Zeeman-slower-based setup and is readily adaptable to other open-shell lanthanides.
We present a compact design of dual-beam Zeeman slower optimized for efficient production of cold atom applications. Traditional single-beam configurations face challenges from substantial residual atomic flux impacting downstream optical windows, resulting in increased system size, atomic deposition contamination, and a reduced operational lifetime. Our approach employs two oblique laser beams and a capillary-array collimation system to address these challenges while maintaining efficient deceleration. For rubidium (87^{87}87Rb), simulations demonstrate a significant increase in the fraction of atoms captured by a two-dimensional magneto-optical trap (2D-MOT) and nearly eliminate atom-induced contamination probability at optical windows, all within a compact Zeeman slower length of 44 cm. Experimental validation with Rb and Yb demonstrates highly efficient atomic loading within the same compact design. This advancement represents a substantial improvement for high-flux cold atom applications, providing reliable performance for high-precision metrology, quantum computation and simulation.
This thesis describes the design and construction of a new apparatus to laser cool and trap Yb and Cs atoms with the ultimate aim of creating ultracold molecules with both an electric and magnetic dipole moment, which are of great interest in a range of fields. The Yb and Cs atomic beams are first generated and overlapped in a dual species oven. A collimated atomic beam of the two species is formed by the use of an array of capillary tubes at the exit of the oven. At this stage the atoms have an average velocity of 311m/s or 264m/s for Yb and Cs respectively, therefore it is necessary to reduce their velocity before they can be trapped in a magneto-optical trap (MOT). This initial stage of slowing is carried out with a Zeeman slower. Due to their atomic properties, Yb and Cs atoms are unable to be slowed by the same magnetic field profile therefore they cannot be loaded simultaneously, however, the Zeeman slower can load the atoms into a MOT sequentially. Once their velocities have been reduced to approximately 48m/s (10m/s) the Cs (Yb) atoms can be captured in a MOT. The laser systems for cooling Yb and Cs are also presented. Laser cooling of Cs is achieved on the D2 transition at 852.3nm whereas Yb can either be cooled on the 1S0 to 1P1 or 1S0 to 3P1 transitions at 398.9nm or 555.8nm respectively. Due to the relative linewidths of these transitions (2π×28.0MHz and 2π × 182.2kHz), Zeeman slowing is performed for Yb on the 1S0 to 1P1 transition and magneto-optical trapping on the 1S0 to 3P1 transition. A Cs MOT with 1 × 10^8 atoms and an Yb MOT with the order of 10^8 atoms on the narrow 556nm transition are demonstrated. The mixture can be sequentially loaded into a dual species MOT, paving the way for many further experiments exploring this novel mixture.