Broadband SNAIL parametric amplifier with microstrip impedance transformer
Daria A. Moskaleva, Dmitry O. Moskalev, Nikita S. Smirnov, Аnton I. Ivanov, Aleksei R. Matanin, Victor I. Polozov, Vladimir V. Echeistov, Elizaveta I. Malevannaya, Andrey A. Samoylov, E. V. Zikiy, Ilya A. Rodionov
Josephson parametric amplifiers are an important part of a modern superconducting quantum computing platform and squeezed quantum states generation devices. Traveling wave and impedance-matched parametric amplifiers provide broad bandwidth for high-fidelity single-shot readout of multiple qubit superconducting circuits. Here, we present a quantum-limited 3-wave-mixing parametric amplifier based on superconducting nonlinear asymmetric inductive elements (SNAILs), whose useful bandwidth is enhanced with an on-chip two-section impedance-matching circuit based on microstrip transmission lines. The amplifier dynamic range is increased using an array of 67 SNAILs with 268 Josephson junctions, forming a nonlinear quarter-wave resonator. Operating in a current-pumped mode, we experimentally demonstrate an average gain of 17 dB across 300 MHz bandwidth, along with an average saturation power of –100 dBm, which can go as high as −97 dBm with quantum-limited noise performance. Moreover, the amplifier can be fabricated using a simple technology with just one e-beam lithography step.
Josephson parametric amplifiers are an important part of a modern superconducting quantum computing platform and squeezed quantum states generation devices. Traveling wave and impedance-matched parametric amplifiers provide broad bandwidth for high-fidelity single-shot readout of multiple qubit superconducting circuits. Here, we present a quantum-limited 3-wave-mixing parametric amplifier based on superconducting nonlinear asymmetric inductive elements (SNAILs), whose useful bandwidth is enhanced with an on-chip two-section impedance-matching circuit based on microstrip transmission lines. The amplifier dynamic range is increased using an array of 67 SNAILs with 268 Josephson junctions, forming a nonlinear quarter-wave resonator. Operating in a current-pumped mode, we experimentally demonstrate an average gain of 17 dB across 300 MHz bandwidth, along with an average saturation power of –100 dBm, which can go as high as −97 dBm with quantum-limited noise performance. Moreover, the amplifier can be fabricated using a simple technology with just one e-beam lithography step.
Broadband impedance-matched Josephson parametric amplifiers are key components for high-fidelity single-shot multi-qubit readout. Nowadays, several types of impedance matched parametric amplifiers have been proposed: the first is an impedance-matched parametric amplifier based on a Klopfenstein taper, and the second is the impedance-matched parametric amplifier based on auxiliary resonators. Here, we present the quantum-limited 3-wave-mixing lumped-element SNAIL parametric amplifier with two-pole impedance matching transformer. A two-pole Chebyshev matching network with shunted resonators is based on parallel-plate capacitors and superconducting planar coil. Operating in a flux-pumped mode, we experimentally demonstrate an average gain of 15 dB across a 600 MHz bandwidth, along with an average saturation power of −107 dBm and quantum-limited noise temperature.
Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.
We present a SNAIL-based parametric amplifier that integrates a lumped-element impedance matching network for increased bandwidth and an on-chip pump-port filter for efficient pump delivery. The amplifier is fabricated using a single-layer optical lithography step, followed by a single-layer electron beam lithography step. We measure a flat 20 dB gain profile with less than 1 dB ripple across a bandwidth of up to 250 MHz on multiple devices, demonstrating robust performance against variations arising from fabrication and packaging. We characterize the amplifier's linearity by analyzing gain compression and intermodulation distortion under simultaneous multi-tone excitation. We show that the intermodulation products remain suppressed by more than 23 dB relative to the signal tones, even at the 1 dB gain compression point. We further validate its utility by performing simultaneous high-fidelity readout of two transmon qubits, achieving state assignment fidelities of 99.51% and 98.55%. The combination of compact design, fabrication simplicity, and performance robustness makes this amplifier a practical device for quantum experiments with superconducting circuits.
Superconducting quantum circuits are a leading platform for building a large-scale quantum processor [1]. A crucial component necessary for the high-fidelity readout of qubits in this framework, is an ultra-low-noise microwave amplifier. Thus, over the past two decades, superconducting Josephson parametric amplifiers (JPAs) have been developed that achieve near quantum-limited noise performance, an order of magnitude lower than competing microwave amplifiers based on semiconductor transistors [2]. Nevertheless, JPAs suffer from drawbacks such as limited bandwidth and compression power that makes them difficult to use in an eventual large-scale quantum processor. Thus, an ongoing theme in JPA development is to optimize the circuit to improve these specifications without sacrificing other desirable properties such as the noise performance, ease of construction and operation, etc. Here, we review some results of optimizing a specific JPA circuit called the SNAIL parametric amplifier [3]–[5], shown in Fig. 1, where the acronym SNAIL refers to the Superconducting Nonlinear Asymmetric Inductive eLement. The SNAIL is a composite element made from conventional Al/AlOx/Al Josephson junctions, which has a nonlinear current-phase relation that can be approximated as a nonlinear inductance. By applying a strong microwave frequency pump to modulate the nonlinear inductance, parametric amplification can be realized. By device and circuit engineering we have demonstrated two orders of magnitude improvement in compression power (Fig. 2) in such devices without sacrificing other desirable characteristics.
Broadband quantum-limited parametric amplifiers (PAs) are essential components in quantum information science and technology. Impedance-engineered resonator-based PAs and traveling-wave PAs are the primary approaches taken to overcome the gain-bandwidth constraint. While the former PAs are simpler to fabricate, the target characteristic impedance ZNR of the nonlinear resonator has been restricted to be below $10\phantom{\rule{0.2em}{0ex}}\mathrm{\ensuremath{\Omega}}$, requiring large capacitance. Moreover, these PAs have only been implemented with aluminum-based Josephson junctions (JJs), hindering their operation at high temperatures or strong magnetic fields. To address these issues, we propose a three-stage impedance-transformer scheme, showcased with a 20 nm thick, 250 nm wide, high-kinetic-inductance niobium-titanium-nitride (NbTiN) film. Our scheme enables ZNR up to several tens of ohms---a tenfold improvement over conventional designs, achieved through an additional quarter-wavelength transmission line with a characteristic impedance of 180 $\mathrm{\ensuremath{\Omega}}$. Our kinetic-inductance impedance-engineered parametric amplifiers (KIMPAs), featuring a 330 fF shunt capacitor, demonstrate a phase-preserving amplification with a 450-MHz bandwidth at 17 dB gain, and added noise ranging from 0.5 to 1.3 quanta near the center frequency of 8.4 GHz. Owing to the high critical current of the NbTiN nanowire, the KIMPA also achieves an output saturation power of up to $\ensuremath{-}51\ifmmode\pm\else\textpm\fi{}3$ dBm, approximately 25 dB higher than that of JJ-based PAs. This scheme also opens new possibilities for other three-wave-mixing building blocks.
We present a fishbone-like lumped-element artificial transmission line to overcome impedance mismatch in a reflection-type Josephson parametric amplifier between a nonlinear resonator and an external transmission line. Using this easily prepared architecture, we design and fabricate a broadband Josephson parametric amplifier, which has gain in an excess of 20 dB with a bandwidth of hundreds of MHz. Furthermore, by varying the working point of the device, the operating frequency of amplification can be tuned in a wide frequency range of 1 GHz while the amplifier operates in the mode of either three-wave mixing or four-wave mixing. Such a parametric amplifier is suitable for engineering applications of superconducting circuit quantum electrodynamics.